Viavi T-BERD/MTS-5800 Stücklistenhandbuch

VIAVI Solutions

Quick Card

T-BERD®/MTS-5800 Network Tester

Ethernet Optics Self-Test

This quick card describes how to test SFP+, SFP28, QSFP+, QSFP28 and CFP4 optical transceivers using

the T-BERD/MTS 5800.

Equipment Requirements:

•T-BERD/MTS-5800 equipped with the following:

oBERT software release V27.2 or greater

oTest options:

▪C510GELAN for 10G Gigabit Ethernet

▪C525GE for 25Gigabit Ethernet

▪C540GE for 40Gigabit Ethernet

▪C5100GE for 100Gigabit Ethernet

•Jumper Cable or Loopback Plug:

oSingle Mode LC Loopback plug or LC-LC Jumper Cable for

10GBASE-LR, 25GBASE-LR, 40GBASE-LR4, and

100GBASE-LR4 (VIAVI Part # CB-019965)

oMultimode LC Loopback plug or -LC Jumper Cable for

10GBASE-SR and 25GBASE-SR (VIAVI Part # CB-019967)

o12-Fiber Multimode MPO Loopback plug for

40GBASE-SR4 and 100GBASE-SR4

(VIAVI Part # CB-MPOLB-12F)

•Fiber optic inspection microscope

(VIAVI P5000i or FiberChek Probe)

•Fiber Optic Cleaning supplies

Information Requirements:

•BER Threshold

Figure 1: Equipment Requirements

Fiber Inspection Guidelines:

•Use the VIAVI P5000i or FiberChek Probe microscope to

inspect the jumper cable or loopback plug before

connection to the optical transceiver.

•Focus the fiber on the screen. If dirty, clean the connector.

•If it appears clean, run inspection test.

•If it fails, clean the fiber and re-run inspection test.

Repeat until it passes.

Figure 2: Inspect Before You Connect (IBYC)

VIAVI Solutions

Figure 3: T-BERD 5800v2 Dual Port mainframe

Figure 4: T-BERD 5800-100G mainframe

Connect Optics Under Test:

1. Insert optics under test into the Port 1 slot on the top of T-BERD/MTS 5800.

2. After inspecting the fiber end faces, connect the Tx and Rx ports using an LC-LC jumper cable or loopback

plug.

Launch Test:

1. Press the Power button to turn on the

test set.

2. Using the Select Test menu, Quick Launch

menu, or Job Manager, launch an Ethernet

10GigE LAN, 25GigE, 40GigE or 100GigE, P1

Optics Self-Test; for example:

Ethernet►100GigE►P1 Optics Self-Test.

3. Tap the bottom button to Start a

New Configuration.

Figure 5: Startup screen

Configure Test:

1. Choose the Test Duration. Recommended is

the suggested setting. Duration will be

calculated based on the Line Rate and BER

Threshold.

2. Select the BER Threshold. Lower values

increase the Recommended test duration.

3. Check Enable the PPM Line Offset box.

4. The default value for PPM Max Offset is

+/- 100 and is the recommended value.

5. Check the Stop on Error box if you don’t want

the test to continue in case of failure.

6. Tap to proceed to the

Report Information screen.

Figure 6: Configure

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest you,

visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

Report Information:

1. If you wish to save a report, you can enter

the Customer Name, Technician ID,

Test Location, Work Order, and

Comments/Notes.

2. Tap to proceed to the

Optics Self-Test screen.

Figure 7: Report Information

Optics Self-Test:

1. Tap Test SFP Optics, Test QSFP28 Optics, or

Test CFP4 Optics to start the test.

2. At the end of the test, select the Result

Overview tab and verify all tests pass.

Figure 8: Results Overview (10GBASE-LR Optics)

3. If you are testing QSFP+, QSFP28, or CFP4

optics, select the Optical Power (dBm) tab

and verify Rx Level for each Lambda is within

+/- 1 dBm of each other.

4. Tap to proceed to the

Report screen.

Figure 9: Optical Power (dBm) Results (100GBASE-LR4 optics)

Create Report:

1. Tap to generate a test report in

.pdf format

2. Tap twice to exit the

Optics Self-Test workflow.

Figure 10: Report screen

Inhaltsverzeichnis

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi T-BERD 6000A V2 Bedienungsanleitung

Viavi

Viavi IFR 6000 Bedienungsanleitung

Viavi

Viavi OneExpert ONX CATV 620 Bedienungsanleitung

Viavi

Viavi OTU-8000 Stücklistenhandbuch

Viavi

Viavi Certifier40G Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-5800 OCC-4056C Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi Certifier Series Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-2000 Stücklistenhandbuch

Viavi

Viavi MTS 2000 Bedienungsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800-100G Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Viavi

Viavi HST-3000 Bedienungsanleitung

Viavi

Viavi Seeker X with MCA III Bedienungsanleitung

Viavi

Viavi SmartOTDR Mainframe Bedienungsanleitung

Viavi

Viavi ComXpert CX100 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Viavi

Viavi 3900 Series Betriebsanleitung

Viavi

Viavi 3550 Bedienungsanleitung

Viavi

Viavi NSC-100 Bedienungsanleitung

Viavi

Viavi AVX-10K Bedienungsanleitung

Viavi

Viavi HST-3000 Stücklistenhandbuch

Viavi

Viavi HST-3000 Stücklistenhandbuch

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung