Viavi MTS 2000 Bedienungsanleitung

VIAVI//Public

T-BERD/MTS-2000 Modular Test Set

QUICK CARD

► Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (OCC Port, bulkhead

connectors, patch cables, etc.)

► Focus fiber on the screen. If dirty, clean the

end-face.

► If it appears clean, run inspection test.

► If it fails, clean the fiber and re-run inspection

test. Repeat until it passes.

Figure 2: Inspect Before You Connect

Figure 1: Equipment Requirements

Optical Spectrum Analyzers. The Best OSA Modules & Platforms (viavisolutions.com)

DWDM Optical Channel Checker

This quick card describes how to connect to a fiber under test, configure DWDM Optical

Channel Checker (OCC) test setups, run tests, and analyze results with a T-BERD/MTS-

2000 equipped with an OCC-4056C module.

Note: The OCC module is used to monitor wavelengths on a live network. Care

should be exercised when unplugging fibers from the network as the fibers

may be carrying traffic.

► T-BERD/MTS-2000 equipped with the

following:

► Fiber Optics Software Release V21.0 or

greater

► OCC-4056C DWDM OCC Module

► Fiber optic cleaning and inspection tools

► Fiber optic patch cable (Launch Cable)

► Optical Coupler to connect patch cable to

Fiber Under Test

VIAVI//Public

T-BERD/MTS-2000 Modular Test Set

QUICK CARD

Optical Spectrum Analyzers. The Best OSA Modules & Platforms (viavisolutions.com)

CONNECT TO FIBER UNDER TEST (FUT)

All fibers and connectors should be cleaned and inspected prior to connection, as described on page 1.

The Nano OSA is typically connected to the FUT via a Monitor Port or splitter/tap to not disrupt service.

The Nano OSA can also be directly connected to the common port or common fiber via a coupler during

turn up or maintenance:

1. Inspect the OCC port on top of the test set.

2. If connecting to the Common Cable, connect the Common

Cable to an optical coupler with the same connector type and

inspect the fiber end face in the coupler.

3. If connecting to the Monitor Port or Common Port on the Mux,

inspect the Mux Port.

4. Inspect the fiber end face of the Patch Cable and connect the

cable to the OCC port.

5. Inspect the other fiber end face of the Patch Cable and Connect

the Launch Cable to the coupler or Mux port.

Figure 3: OCC Port Inspection

Figure 4: Connecting to Monitor Port

Figure 5: Connecting to Common Cable

VIAVI//Public

T-BERD/MTS-2000 Modular Test Set

QUICK CARD

Optical Spectrum Analyzers. The Best OSA Modules & Platforms (viavisolutions.com)

CONFI G U RE T E ST SETUP

LAUNCH TEST

1. Press the ON/OFF button to start the

test set.

2. Press the Home button to display

the Home view with the OCC-4056cicon.

3. Tap the OCC-4056Cicon

until it is yellow and highlighted.

Figure 6: Home Screen

1. Tap Setup icon.

2. Tap Auto-set to auto-configure the OCC

for a single sweep.

3. If a splitter/tap is used to access the

signal, Tap the Analysis tab and set

Splitter Value to the splitter loss

(in dB or %).

Figure 7: Setup Menu

Figure 8: Analysis Settings

VIAVI//Public

T-BERD/MTS-2000 Modular Test Set

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

RUN SW EE P TE S T

3. Tap START icon (upper right) to run scan

4. View Results after scan completes. Use your finger or stylus to scroll up/down as needed.

Total # of

Channels

detected

Verify Channels &

Power Levels (dBm)

Measure offset

(detect optics going bad)

Measure

Actual wavelengths

Andere Handbücher für MTS 2000

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi T-BIRD-4000 Stücklistenhandbuch

Viavi

Viavi HST-3000 Bedienungsanleitung

Viavi

Viavi T-BERD 5800 Bedienungsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi FBP-HD4i Bedienungsanleitung

Viavi

Viavi OneExpert ONX CATV Bedienungsanleitung

Viavi

Viavi ONX 580 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi AVX-10K Bedienungsanleitung

Viavi

Viavi ComXpert CX100 Bedienungsanleitung

Viavi

Viavi OBS-500 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-2000 Stücklistenhandbuch

Viavi

Viavi FBP-HD4iP Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Viavi

Viavi NSC-200 Bedienungsanleitung

Viavi

Viavi SmartClass Fiber OLS-85 Bedienungsanleitung

Viavi

Viavi T-BERD MTS-580 Stücklistenhandbuch

Viavi

Viavi OneAdvisor ONA-800 Bedienungsanleitung

Viavi

Viavi 3900 Series Bedienungsanleitung

Viavi

Viavi HST-3000 Bedienungsanleitung

Viavi

Viavi FBP-HD4i Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 2000 Bedienungsanleitung

Viavi

Viavi 3550 Bedienungsanleitung

Viavi

Viavi IFR 4000 Stücklistenhandbuch

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung