Viper 106V Bedienungsanleitung

110066VV

IInnssttaallllaattiioonnGGuuiiddee

contents

what is included . . . . . . . . . . . . . .3

system configuration . . . . . . . . . .3

wire connection guide . . . . . . . . .4

immobiliser harness wiring

diagram . . . . . . . . . . . . . . . . . .4

power harness wiring diagram .4

touch-key harness wiring

diagram . . . . . . . . . . . . . . . . . .5

immobiliser harness wiring

guide . . . . . . . . . . . . . . . . . . . .6

power harness wiring guide . . .6

touch-key receptacle wiring

guide . . . . . . . . . . . . . . . . . . . .7

passenger compartment . . . . . . . .7

mounting the control unit . . . . .7

programming instructions . . . . .8

certificate of installation . . . . . . .8

troubleshooting . . . . . . . . . . . . . .8

wiring reference guide . . . . . . . . .9

notes . . . . . . . . . . . . . . . . . . . . . .10

Clifford®, Code-Hopping™, Directed®, Valet®are all Trademarks or Registered Trademarks of Directed Electronics, Inc.

IIMMPPOORRTTAANNTT!!The Viper 106V system is designed to be installed in any

petrol or common rail diesel vehicle with a 12-volt battery.

what is included

zOne control module with 9-wire immob- zOne Owner’s Guide

iliser harness

z2-Touch-keys zTwo window decals

zTouch-key receptacle with LED zOne hardware pack

system configuration

The Viper 106V system has a control module which works in conjunction with a touch-

key to allow the vehicle to be started. A total of 3 touch-keys can be programmed into

the control module.

NNOOTTEE::The touch-key receptacle must be installed so that the

LED is visible to the vehicle operator when using the touch-key.

TOUCH-KEY RECEPTACLE LED

TOUCH-KEY

www.directed.com

wire connection guide

immobiliser harness wiring diagram

___

power harness wiring diagram

___

NNOOTTEE::Please remove all wire description tags from wiring after

connection to the vehicle.

GND2 (Ground 2)

GND1 (Ground 1)

+12V

NNOOTTEE::All wires are BLACK. Each wire is marked with its function.

The description listed below is the marking on each wire and then

its function, in brackets.

IGN: Ignition Side (Ignition Interrupt Com)

STR: Key Side (Starter Interrupt 87)

Fuel Pump Input (Fuel Pump Interrupt 87)

IGN: Key Side (Ignition Interrupt 87)

STR: Starter Side (Starter Interrupt Com)

Fuel Pump Output (Fuel Pump Interrupt Com)

NNOOTTEE::All wires are BLACK. Each pair is an immobiliser circuit

input and output. Each wire is marked with its function. The descrip-

tion listed below is the marking on each wire and then its function,

in brackets.

touch-key harness wiring diagram

___

___ LED +2V

Ground

Data

NNOOTTEE::All wires are BLACK. Each wire is marked with its func-

tion. The Touch-Key harness has 3-pin connectors to facilitate

the connection from the control module to the Touch-Key recep-

tacle. The functions are listed below for reference only.

www.directed.com

immobiliser harness wiring guide

This guide describes in detail the connection of each wire. Please read the instructions

carefully to ensure a thorough understanding of this unit and how it operates. Locate

the main ignition, starter and fuel pump circuit wires with a multimeter. Cut the appro-

priate wire and attach the key side and car side wires to the corresponding wires on

the 6-wire immobiliser harness.

IGN: Key Side

This wire is connected to the ignition key side of the ignition circuit. This wire should

be +12volt with the ignition turned on and in the cranking position.

IGN: Ignition Side

Connect this wire to the ignition output side of the ignition circuit.

STR: Key Side

This wire is connected to the starter key side of the starter solenoid.

STR: Starter Side

Connect this wire to the starter solenoid side of the starter circuit.

Fuel Pump Input

This wire is connected to the input side of the fuel pump circuit or ground if not used.

Fuel Pump Output

Connect this wire to the fuel pump output high polarity side of the fuel pump circuit or

ground if not used.

power harness wiring guide

+12V

Connect the +12V wire via fuse supplied to an unfused source at the vehicle's fuse-

box.

GND1 and GND2

Connect the BLACK wires (2 and 3) to separate ground locations using a factory bolt

that does NOT have any vehicle component grounds attached to it or drill a new hole

if required. A screw should only be used in conjunction with a two-sided lock wash-

er. Under dash brackets and door sheet metal are not acceptable ground points.

touch-key receptacle wiring guide

Mount the touch-key receptacle in a position accessible to the operator of the vehicle

and so that the LED is visible to the operator. A bracket is provided to allow an addi-

tional mounting method if required.

Plug the touch-key receptacle harness into the wire harness plug from the control mod-

ule.

passenger compartment

mounting the control unit

Select an area behind the dash that will allow you to securely fasten the unit using the

screws provided in the hardware pack. Do not mount the unit near moving parts or

in direct path of air blowing from the heater vents.

NNOOTTEE::When mounting the control module the metal enclosure

must be used.

NNOOTTEE::The Viper 106V control unit must be installed inside the

vehicle. Under no circumstances should the unit be installed

under the bonnet or other similarly hostile environment.

NNOOTTEE::Please remove all wire description tags from wiring after

connection to the vehicle.

www.directed.com

programming instructions

Use the procedure below to program touch-keys into the system. A maximum of 3

touch-keys can be programmed into the system.

1. Turn the ignition On then Off 12 times.

2. The LED will illuminate continuously.

3. Insert the touch-key to be programmed into the touch-key receptor.

4. The LED will turn Off for 1-second and then back On continuously. The touch-

key is now programmed.

5. After 15 seconds of no activity the LED will extinguish and the system will exit the

programming routine.

certificate of installation

After installation you must fill out the certificate of installation. Once you have filled

out all information on the certificate the customer must sign and date it. Distribute the

copies as follows:

zWhite (top) copy - customer

zBlue copy - customer’s insurance broker

zPink copy - Directed Electronics, UK office

zGreen copy - installing dealer

troubleshooting

The Touch-Key does not work.

zMake sure that the harness is plugged in. (Refer to the wiring reference guide.)

zHas the Touch-Key been programmed to the system.

The system does not work (no LED illumination).

zCheck the fuse in the power harness.

NNOOTTEE::If more than one touch-key is required to be programmed,

then repeat steps 3 and 4 after the first touch-key is programmed.

NNOOTTEE::In order to program touch-keys into the system, the sys-

tem must be disarmed.

wiring reference guide

NNOOTTEE::Please remove all wire description tags from wiring after

connection to vehicle.

NNOOTTEE::The current draw for the entire system is less than 9 mA. Power

supply voltage range is 9 to 16 volts. The current handling capacity for

each immobilisation circuit is 20amps continuous/30amps peak.

106V

BATTERY

FUSE BOX +-

TOUCH-KEY

3-PIN

GND1

GND2

+12V

FUEL PUMP

KEY ON



CUT FUEL PUMP OUTPUT

FUEL PUMP INPUT

POWER HARNESS

TOUCH-KEY HARNESS

IMMOBILISER HARNESS

CONNECT TO 2

SEPARATE GROUNDS

FUEL PUMP (OPTIONAL)

GROUND BOTH OF THE

WIRES FROM THE 106V

IF NOT USED.

IGNITION

SWITCH



CUT

IGNITION

IGN: IGNITION SIDE

IGN: KEY SIDE



CUT

STR: KEY SIDE

STR: STARTER SIDE

STARTER

www.directed.com

notes

________________________________________

Inhaltsverzeichnis

Andere Viper Autoalarmanlage Handbücher

Viper

Viper 5901 Bedienungsanleitung

Viper

Viper G5102V Bedienungsanleitung

Viper

Viper 1002 Bedienungsanleitung

Viper

Viper SmartStart 3000 Series Bedienungsanleitung

Viper

Viper SmartStart VSM200 Series Bedienungsanleitung

Viper

Viper 211HV Bedienungsanleitung

Viper

Viper 4806V Bedienungsanleitung

Viper

Viper 4103XV Bedienungsanleitung

Viper

Viper 4218V Bedienungsanleitung

Viper

Viper 700 ESP Bedienungsanleitung

Viper

Viper 480XV Bedienungsanleitung

Viper

Viper 4606V Bedienungsanleitung

Viper

Viper Directed 4706V Bedienungsanleitung

Viper

Viper 5902 Bedienungsanleitung

Viper

Viper 300+ Bedienungsanleitung

Viper

Viper 550 ESP Bedienungsanleitung

Viper

Viper 5104 1-Way Bedienungsanleitung

Viper

Viper 591XV Bedienungsanleitung

Viper

Viper 7900 Bedienungsanleitung

Viper

Viper 3305V Bedienungsanleitung

Viper

Viper 480XV Bedienungsanleitung

Viper

Viper Model 3002 Bedienungsanleitung

Viper

Viper 5606V Bedienungsanleitung

Viper

Viper 4108V Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung