Viper VN20DS Bedienungsanleitung

CONGRATULATIONS on your purchase of a Viper product

and welcome to the V.I.P. family. We appreciate your

business and will do everything in our power to keep you happy

with your purchase for many years to come.

As part of the V.I.P. family, you are entitled to the best

protection by one of the most comprehensive warranties in

the industry.

Thank-you for purchasing Viper products!

Tom Vander Bie, CEO

TABLE OF CONTENTS

Safety Precautions 3

Machine Operation 4

Machine Maintenance & Storage 4

Parts List 5---8

Wiring Diagram 9

SAFETY PRECAUTIONS

GROUNDING INSTRUCTIONS

General –This floor – finishing machine shall be

grounded while in use to protect the operator

from electric shock. The machine is provided

with a three –conductor cord and a three contact

grounding type attachment plug to fit the proper

grounding type receptacle. The green [or green

and yellow] conductor in the cord is the

grounding wire. Never connect this wire to other

than the grounding pin of the attachment plug.

This machine is for use on a nominal 120-Volt

circuit and has a grounding plug that resembles

the plug illustrated in figure below. Make sure

that the machine is connected to an outlet

having the same configuration as the plug. No

adapter should be used with this machine.

This machine is intended for Commercial use. It

is constructed for use in an indoor environment

and is not intended for any other use. Use only

recommended accessories.

All operators shall read, understand and

exercise the following safety precautions:

1] Do not operate machine:

-Unless trained and authorized.

-Unless you have read and understand

operators manual.

-In flammable or explosive areas.

-With a damaged cord or plug.

-If not in proper operating condition.

-In outdoor areas.

-In standing water.

-With the use of extension cords.

2] Before operating machine:

-Make sure all safety devices are in place

and operate properly.

3] When using machine:

-Do not run machine over cord.

-Do not pull machine by cord or plug.

-Do not pull cord around sharp edges of

corners.

-Do not unplug by pulling on the cord.

-Do not stretch cord.

-Do not handle plug with wet hands.

-Keep cord away from heated surfaces.

-Report machine damage of faulty

operation immediately.

4] Before leaving or servicing machine:

-Turn off machine.

-Unplug cord from outlet.

5] When servicing machine:

-Unplug cord from outlet.

-Use manufacturer supplied or approved

replacements parts.

Operation of Floor Machines

* READ OPERATORS MANUAL

THOROUGHLY PRIOR TO OPERATING OR

SERVICING THIS MACHINE.

GENERAL USE

Remove any obstructions or other

obstacles in the area which is to be

cleaned.

Place the handle in the upright position

and tilt machine back until handle rests

on the floor

* Be sure the machine is not plugged into

an outlet

Attach the pad driver or brush to the

machine by placing the clutch plate over

the gearbox hub and turning the driver

/ brush ¼ turn.

Place machine back into its upright

position.

Plug power cord into a grounded outlet.

* N

Never use an extension cord in

conjunction with the standard power cord.

The handle height may be adjusted by

lifting up the compression handle which

is located on the right side of the handle

tube about 1 foot above floor level.

Release the compression handle and

adjust handle to safe operating height,

then push back down on the

compression handle to lock the handle in

operating position.

Select either low speed (185rpm) or

high speed (330rpm) by pushing the

motor mounted switch into the low or

high position.

* N

Never change the speed while operating

the machine. Be sure the power is turned

off prior to changing the speed.

To start the machine, press the red

safety button on the top of the upper

switch housing, and then squeeze either

of the operating triggers. (the safety

button must be depressed prior to

squeezing the operating triggers.)

When the machine is in operation, both

hands should be placed on the switch

housing (upper handle).

10.

During operation, to make the

machine go right, gently raise the

handle. To make the machine go left,

gently lower the handle.

11.

To stop the machine at any time,

simply release the operating trigger(s)

and the machine will stop automatically.

MAINTENANCE

To keep the machine performing well for

many years, please follow the following

maintenance procedures.

* Always confirm that the machine is

unplugged prior to performing any

maintenance or repairs.

Unplug machine as soon as you are

done using it.

Tilt machine back and remove pad driver

or brush.

* Never store a low speed machine with

the pad driver or brush mounted to the

machine.

Clean the outside of the machine with a

mild cleaner.

Check power cord for any damage. If

damage is detected, replace power cord

immediately.

Lubricate wheels with a water resistant

lubricant once a month.

Check machine for loose or missing nuts

and bolts, and replace as necessary.

If the machine is used in a dusty

environment, you may remove the motor

cover and blow the motor clean with

compressed air. This will ensure proper

ventilation, and allow the motor to run

cooler.

STORAGE

Unplug machine from power source and

wrap cord on handle.

Tilt machine back and remove pad driver

or brush.

Store machine in upright position and in

a dry area.

DIA

PART

NUMBER DESCRIPTION NO

REQ'D

1 VF30016 HANDLE RELEASE 1

2 VF30015 BOLT,HANDLE RELEASE 1

3 VF30018 WASHER,PLAIN 2

4 VF13503 NUT,LOCK,M8X5.7 1

5 VF30017 SCREW 1

6 VF30014 COVER,HOOK 1

7 VF45125 CORD,HANDLE 1

8 AS41901 PLUG PROTECTOR SMALL MALE 1

9 VF50120A GROMMET 1

10 VF13504 NUT,LOCK,M10 1

11 VF13517 WASHER,PLAIN 1

12 VF14114 SCREW M8X55 1

13 VF30013 HOOK,CORD 1

14 VF13493 SCREW,M6X10 1

15 AS112205 TUBE 1

16 VF44018 LEVER,SOLUTION 1

17 VV13661 SCREW,M4X12 2

18 VF48306 PIN 3

HANDLE GROUP FOR VN20DS

19 VF44016 LEVER,LEFT,SWITCH 1

20 VF45119 CORD,POWER SUPPLY 1

21 AS22009 STRAIN RELIEF,CORD 1

22 VF30108 GASKET,HANDLE,SOLUTION 1

23 VF14223 SCREW,M6X25 2

24 VF14218 SCREW,M6X45 2

25 VF13528 TEETH WASHER,M6 2

26 VF30102 REAR COVER 1

27 VF99010C BREAKER,CIRCUIT 1

28 VF30109 COVER 1

29 GT13013 NUT,M4 3

30 VF48309 CLAMP BLOCK 1

31 VF44017 LEVER,RIGHT,SWITCH 1

32 VF44203 SWITCH ASSY 1

33 VF14212 SCREW M3X25 2

34 VF13527 WASHER,TEETH,M4 1

35 VF13526 SCREW,M4X30 1

36 VF46705 SAFETY BOTTON 1

37 GV40218 SPRING,SAFETY BUTTON 1

38 VF48310 HANDLE GRIP 2

39 VF30101 FRONT COVER 1

40 VF47035A LOGO 1

41 VF13604 WASHER,TEETH,M5 4

42 VF14222 SCREW

M5X12 4

DIA

PART

NUMBER DESCRIPTION NO

REQ'D

BASE GROUP FOR VN20DS

1 GT13080 SCREW, M6 X 30 4

2 VF30011 CLAMP BLOCK, HANDLE 1

3 VF30026 AXLE 1

4 VF30020 BRACKET, LEFT HANDLE 1

5 VV20274 WASHER, PLAIN, M13 4

6 GV40235 CLAMP BLOCK, AXLE 2

7 VV13621 SCREW, SELF-TAPPING, ST, M5 X 20 4

VF13474A

WASHER PLAIN M5

VF13474A

WASHER

PLAIN

9 VF13613 SCREW, M5 X 20 2

10 VA13474 SCREW, M5 X 16 5

11 VF13524 WASHER, PLAIN, M8 4

12 VF13519 WASHER, LOCK, M8 4

13 VF13618 SCREW, 5/16" - 2 1/4" 4

14 MF-VF002-4A SCREW, SELF-TAPPING, 1/4"-1" 6

15 MF-VF002-2 CLUTCH PLATE 1

16 MF-VF022 PAD HOLDER, 19" 1

17 VF30004 BUMPER, 20" 1

18 ZD48315 BEARING, #6002Z 1

19 ZD48200 SHAFT & ROTOR ASSEMBLY 1

20 VF30006 FRAME, 20" 1

21 VF99926-2 KIT, CARBON BRUSH 1

22 VF30008 ALUMINIUM BASE, MOTOR 1

VF40152

HOSE BARB

VF40152

HOSE

BARB

24 VF30019 BRACKET, HANDLE, RIGHT 1

25 VF13520 WASHER, LOCK 2

26 VF50119 WASHER, LOCK, M12 2

27 VF48202 WHEEL, 5" 2

28 VF13666 WASHER, M6 2

29 VF44012 SCREW, M6 X 12.7 2

30 ZD40225 BEARING, #6203Z 1

F999802B GEAR BOX 1

32 VF99021 COULPING 1

33 MT01102 SLEEVE 1

34 VF40990 LABEL, DUAL SPEED 1

35 VF41079 LABEL, VIPER 1

36 ZD48310 LABEL, MOTOR 1

37 ZD48000 MOTOR, DUAL SPEED 1

VA13473

SCREW, M4 X 16

VA13473

SCREW,

39 VF44204 RECTIFIER 1

40 VA91347 SWITCH 1

41 ZD48309DY SHELL 1

42 VF13604 WASHER, TOOTH, M5 2

43 VF14214 SCREW, M5 X 8 2

44 GT13014 NUT, NYLON INSERT, M4 2

45 ZD48316A TRIAC ASSEMBLY 1

GT13048

SCREW M4 X 12

GT13048

SCREW

47 VV67405 STRAIN RELIEF, CORD 1

48 VV67405-1A NUT 1

49 AS41902 PLUG PROTECTOR, LARGE, FEMALE 1

50 VF999794 CORD, MOTOR 1

51 ZD48330 KIT, SPEED ADJUSTMENT 1

52 VF40994 READ MANUAL LABEL 1

F40997 SERIAL TAG 1

Inhaltsverzeichnis

Andere Viper Bodenreinigungsmaschine Handbücher

Viper

Viper VN1715 Bedienungsanleitung

Viper

Viper SL1610SE Bedienungsanleitung

Viper

Viper AS1050R Bedienungsanleitung

Viper

Viper FANG 20 Bedienungsanleitung

Viper

Viper AS530R Benutzerhandbuch

Viper

Viper DR1500H-EU Bedienungsanleitung

Viper

Viper VN1715 Bedienungsanleitung

Viper

Viper Fang15B Bedienungsanleitung

Viper

Viper VE 13P-EU Bedienungsanleitung

Viper

Viper VE 13 P Bedienungsanleitung

Viper

Viper VE 17DSP-EU Bedienungsanleitung

Viper

Viper AS380/15B-EU Bedienungsanleitung

Viper

Viper Fang 20HD Bedienungsanleitung

Viper

Viper AS380/15B-EU Bedienungsanleitung

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper AS6690T Benutzerhandbuch

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper CEX410 Bedienungsanleitung

Viper

Viper DR 1500 H Bedienungsanleitung

Viper

Viper TP1500 Bedienungsanleitung

Viper

Viper AS710R Bedienungsanleitung

Viper

Viper AS4335C Benutzerhandbuch

Viper

Viper AS380/15C-EU Bedienungsanleitung

Viper

Viper AS380/15 Benutzerhandbuch

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch