Viper Fang15B Bedienungsanleitung

15-Inch

VF89027-US REV.01

2013-07-17

FANG15B

www.usviper.com

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!USER!MANUAL!

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is constructed for use in an indoor environment and is

not intended for any other use. Use only with recommended accessories.

All operators shall read, understand and exercise the following safety precautions:

1) DO NOT OPERATE MACHINE:

Unless trained and authorized.

Unless you have read and understand the operators manual.

In flammable or explosive areas.

If not in proper operating condition.

In outdoor areas.

2) BEFORE OPERATING MACHINE:

Make sure all safety devices are in place and operate properly.

3) WHEN USING MACHINE:

Go slow on inclines and slippery surfaces.

Follow all safety guidelines.

Be very careful when using the machine in reverse.

Report and fix any damage to machine prior to operating it.

4) BEFORE LEAVING OR SERVICING MACHINE:

Stop machine on level ground.

Turn machine off.

5) WHEN SERVICING MACHINE:

Read operators manual thoroughly prior to operating or servicing this machine.

Use manufacturer supplied or approved replacement parts.

Secure machine with wheel blocks prior to jacking the machine up.

Use approved jack or hoist to safely elevate the machine.

Disconnect batteries prior to working on machine.

Wear gloves when handling batteries or battery cables.

Avoid any contact with battery acid.

Avoid moving parts; do not wear loose fitting clothing while servicing machine.

WARNING！

Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep

Sparks and open flames away! Keep battery compartment open when charging.

WARNING！

lammablematerialscancauseanexplosionorfire.Donotuse flammable materials

in tanks.

WARNING！

lammablematerialsorreactivemetalscancauseexplosionorfire.Donotpickup.

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!USER!MANUAL!

MACHINE SET UP & INSTALLATION

UNCRATING MACHINE

Be sure and check packing carton for any damage. Immediately report any damage to carrier.

Check contents of package to ensure that the following items are included:

1. Machine

2. Batteries(x2)

3. Squeegee assembly

4. Owners Manual

5. Electric Battery Charger Manual（if equipped）

6. Connecting wire for battery and charger (if equipped)

7. Brush

BATTERY DISASSMBLY AND INSTALLATION

1. Switch off the main switch.(47)

2. Remove the recovery tank.(2)

3. Remove the bolt from batteries.(16) Remove or change batteries.

4. Install the batteries on the machine according to the diagram below.

5. Install the recovery tank.

WARNING

Do not connect+ to +,or -to-,when disassembly or install the batteries. It is very dangerous.

!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Battery charging

Charge the batteries. (see Maintenance section)

MACHINE SET UP

Pre-operation checks

1．Sweep or dust mop the surface to be cleaned.

2．Check that squeegee is properly installed.

3．Lower the squeegee (33) with the lever. (26)

4．Ensure batteries are fully charged. (see Battery Charging section)

5．Check that brush is properly installed.

Brush/Pad driver installation and disassembly

NOTE

Only install manually. If automatically installed, it will wear brush hub.

Make sure that the tanks are empty before removing the brush.

1. Turn off the machine.

2. Lay down the machine in the position shown in figure 2. Pull up lift lever (26) to raise the

squeegee. (33)

Figure!1!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!USER!MANUAL!

3. Mount the brush or pad driver onto the drive wheel hub and then rotate counterclockwise until it

locks,as indicated in figure3.

4. To remove the brush/pad, rotate the brush/pad clockwise until it is released from drive hub.

WARNING

Do not turn on the machine in this position as below. In case of brush/pad come out or cause injury.

Squeegee installation

1．Turn off the machine.(47)

2．Pull down the squeegee lift lever (26) to put down the squeegee in the “working”position.

3．Lay down the machine in this position as shown in figure2.

4．Loosen the two knobs (55) on the squeegee and slide the squeegee into the slots on the

squeegee brackets.

5．Tighten the knobs securely.(unscrew the knobs, if to remove)

6．To replace the front/rear squeegee, (56/57) unscrew the thumb knobs. (37)

Figure!3!

Figure!2!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!USER!MANUAL!

Solution tank filling

NOTE

The machine can be filled with a hose or bucket. Do not remove the Solution filter (21) while filling.

1. Fill water into solution tank (3) from the inlet (20) through hose or bucket.

2. Do not overfill the solution tank. It is best to leave a an inch from the top edge.

3. The water temperature must not exceed 40℃.

CAUTION！

Use only low-foam and non-flammable detergents, intended for automatic scrubber applications.

Solution tank draining

NOTE

Solution tank should be drained and cleaned after each scrubber operation is

completed.

1．Unscrew the drain cap (22) on the bottom of solution tank. The solution/water will flow freely

into a bucket or floor drain.

2．Rinse the solution tank with clean water after every use. This will help prevent chemical

buildup and clogging of the solution lid.

3．Replace the drain cap.(22)

Recovery tank draining

NOTE

Recovery tank should be drained and cleaned after each scrubber operation is

completed.

1．Turn the latch (17) on the recovery tank. Remove the recovery tank from machine by

grasping two grooves of tank and pulling up. Open the lid (1) and overturn the recovery tank

to drain the dirty water into a container, or unscrew the drain cap (22) to let water drain into a

bucket.

2．Clean and Rinse the recovery tank with clean water after every use.

3．Re-place the recovery tank on the machine and turn the latch (17) to lock the tank in place.

MACHINE OPERATION

1．Set the handle to a comfortable height by pressing level.(25)

2．Lower the squeegee (33) onto floor by pulling down the lift handle. (26)

3．Turn on the main power switch. (47)

4．Turn on the brush motor switch (48) and the solution switch. (50)

5．Turn on the vacuum motor switch.(49)

6．If necessary, adjust the water flow by manually turning the ball valve.(31)

7．Pull one or both operating triggers. (24) The brush will spin & solution will begin to flow. Push

the machine forward to start cleaning.

OTE

If the battery indicator light (51) is green, the machine can be used. If it is yellow or red,

the batteries must be charged.

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!USER!MANUAL!

CAUTION！

Before lifting the brush, turn off the main power switch. (47)

CAUTION！

If the control panel (46) lights flash simultaneously, this indicates the machine is overloaded. Please turn off

all the switches on the control panel (46) to reset the machine. If problem persists, contact authorized

service provider.

CAUTION！

Operating machine with discharged batteries may cause harm to the batteries or to the machine.

AFTER EACH USE

After scrubbing, please proceed with below actions before storing the machine:

1. Remove the brush / pad-holder.

2. Empty the tanks as shown in the previous paragraph.

3. Perform the daily maintenance procedures.(see Maintenance section)

4. Store the machine in a clean and dry place, with the brush / pad-holder and the squeegee up.

5. If storing in an area that may reach freezing temperatures, be sure to drain all fluids from the

machine prior to storage. Any damage caused by freezing will void the warranty.

MACHINE STORAGE

If the machine is not going to be used for more than 30-days, please proceed with below actions:

1. Perform the procedures shown in ‘After Each Use’ section above.

2. Disconnect the battery connector.

MAINTENANCE

The lifespan of the machine and its maximum operating safety are ensured by correct and regular

maintenance. The following chart provides the scheduled maintenance. The intervals shown may

vary according to individual working conditions.

WARNING

Maintenance procedures must be performed with the machine switched off and the batteries/battery charger

cable disconnected. Moreover, carefully read the instruction in the Safety chapter.

All maintenance procedures must be performed by qualified personnel, or by an authorized Service

Center.

This Manual describes only the most common maintenance procedures.

For additional maintenance procedures, contact your local Service Center.

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!USER!MANUAL!

SCHEDULED MAINTENANCE TABLE

Procedure After each use Weekly Every six

months

Annually

Battery charging

Squeegee cleaning

Brush cleaning

Clean tank, vacuum screen & check top cover

gasket

Squeegee blade check and replacement

Solution filter cleaning

Drain hose filter cleaning

Screw and nut tightening check （1）

Lubricate rotary parts （1）

Check brush motor carbon brushes （2）

Check vacuum motor carbon brushes （2）

（1）After the first 8 working hours.

（2）This maintenance procedure must be performed by an authorized Service Center.

BATTERY CHARGING

NOTE

Charge the batteries when the yellow or red indicator, (51) or at the end of every work cycle.

CAUTION！

Proper battery care will extend battery life

CAUTION！

If the machine is not equipped with on-board battery charger, choose an external battery charger suitable for

the type of batteries installed.

WARNING！

Please use Viper approved charger to charge the batteries.

WARNING！

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!USER!MANUAL!

Pay careful attention when charging WET batteries, as battery fluid could leak. Battery fluid is highly corrosive.

If fluid comes in contact with skin or eyes, rinse thoroughly with water and consult a physician.

1. Place charger and machine in a well ventilated area.

2. Turn machine off. (47)

3. Remove the recovery tank, (2) exposing battery compartment.

4. Plug the charging cable to the grounded wall outlet (100v~240v). Connect the charging cable to

the machine socket.

5. The charging light (30) indicates the batteries are charging. Agreen light indicates battery charging

is completed.

6. Upon the completion of charging, first unplug the charging cable from the wall outlet and then

disconnect from machine.

7. Replace the recovery tank.

NOTE

For further information about the operation of the battery charger,(29) see the charger section.

SQUEEGEE CLEANING

NOTE

For optimal performance, the squeegee blades must be clean, dry and undamaged.

CAUTION !

It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.

SQUEEGEE BLADE CHECK AND REPLACEMENT

1. Take off the squeegee as shown in the previously.

2. Check the edgesof the front & rear blades for cracks. If necessary replace with new blades.

3. Unscrew six the thumb nuts(37) to remove the blades.

4. Check the front & rear blades for cutsand tears. If damage is found,you can flip the blades once &

re-install. If already flipped, please replace with new blades.

5. Install the squeegee in the reverse order of removal.

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!USER!MANUAL!

BRUSH /PAD DRIVER CLEANING

CAUTION！

It is advisable to wear protective gloves when cleaning the brush/pad because there may be sharp debris.

1. Remove the brush/pad as shown in “Machine Use” section.

2. Clean and wash the brush/pad with water and detergent.

3. Check the brush bristles for integrity and wear. If necessary, replace the brush.

4. Check the pad for wear. If necessary, replace the pad driver.

RECOVERY TANK MAINTENANCE

CAUTION！

It is advisable to wear protective gloves when cleaning the tank and vacuum/suction assembly because there

may be sharp debris.

1. Move the machine to the appointed draining area.

2. Turn off the main switch. (47)

3. Remove the recovery tank,(2) clean and rinse both solution/recovery tank, and drain out.

4. Remove vacuum gasket & filter. Clean and re-install.

5. Check the recovery tank lid gasket and the vacuum rubber connector (18) for wear. Replace if

necessary.

NOTE

The gasket ring of recovery tank and the rubber connector between two tanks create vacuum

in the tank. If necessary, replace them.

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!USER!MANUAL!

Control Panel

46．Control panel 51．Battery indicator

47．Mainswitch 52．Brush motor indicator

48．Brush motor switch 53．Vacuum motor indicator

49．Vacuum motor switch 54．Solution indicator

50．Solution switch

TECHINICAL DATA

MODEL

FANG15B

Machine length / width / height 770x500x550MM

Solution tank capacity 15L

Recovery tank capacity 15L

Wheel diameter 254MM

Brush motor 24V/250W

Vacuum motor 24V/250W

Solenoid valve 24V

Maximum gradient when working 2%

Sound level 70dBA

Standard Batteries Dry:（2×12V）24V 33Ah

Batteries size 196 x 130 x 175mm

Power cable length N / A

Cleaning productivity 750m2/hour

Squeegee width 490mm

Brush diameter 380mm

Brush rpm 150rpm

Charger Input 110-224Vac,50-60HZ；Output 24Vdc,5A

Machine net weight 60kg

Machine weight(with charger and

package) 65kg

Carton spec 780x415x590MM

Andere Handbücher für Fang15B

Inhaltsverzeichnis

Andere Viper Bodenreinigungsmaschine Handbücher

Viper

Viper VE 13P-EU Bedienungsanleitung

Viper

Viper AS530R Benutzerhandbuch

Viper

Viper AS380/15B-EU Bedienungsanleitung

Viper

Viper AS380/15B-EU Bedienungsanleitung

Viper

Viper AS710R Bedienungsanleitung

Viper

Viper AS4335C Benutzerhandbuch

Viper

Viper AS710R Bedienungsanleitung

Viper

Viper VN1500 Bedienungsanleitung

Viper

Viper FANG 20 Bedienungsanleitung

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper VE 13 P Bedienungsanleitung

Viper

Viper AS380/15C-EU Bedienungsanleitung

Viper

Viper Dragon DR2000DC Dust Control Bedienungsanleitung

Viper

Viper Fang 20HD Bedienungsanleitung

Viper

Viper VF1517 Bedienungsanleitung

Viper

Viper CEX410-US Bedienungsanleitung

Viper

Viper CEX410 Benutzerhandbuch

Viper

Viper DR1500H-EU Bedienungsanleitung

Viper

Viper TP1500 Bedienungsanleitung

Viper

Viper AS430B Benutzerhandbuch

Viper

Viper VN1715 Bedienungsanleitung

Viper

Viper CEX410 Bedienungsanleitung

Viper

Viper AS6690T-US Bedienungsanleitung

Viper

Viper AS6690T Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch