Vista ViP2 VK2-1080VFD3V9F Bedienungsanleitung

Quick Guide

VK2-1080VFD3V9F

1. Description

This manual applies to the VK2-1080VFD3V9 network camera.

The VK2-1080VFD3V9F camera is designed for internal applications. It’s Full HD video images offer

excellent quality. The Motorised remote set up lens guarantees sharp images throughout the day and

night.

Please read the following manual before installing the camera.

• Installation Steps

Follow these steps to install the cmaera on your local network (LAN):

1. Check the package contents against the list below.

2. Connect the Network Camera. See page 3.

3. Set an IP address. See page 5.

4. Set the password. See page 7.

• Package Component

The system comes with the following components:

Camera unit Installation CD Installation Guide Template Sheet Accessory Kit

Optional OSD Controller

• Contents on the installation CD

1. Camera User’s Manual

2. VK2-Client User’s Manual

3. The Smart Manager User’s Manual

4. VK2-Client Installation software

5. The Smart Manager Installation software

Note: Check your package to make sure that you received the complete system, including all

components shown above.

• Front View

Name

Description

Lens

Allows wide area to be monitored

Extension Cable

Power and IP connectors

• Side View • Bottom View

Name

Description

Micro SD Slot

Micro SD slot for local recording

Status LED

Amber : On System Booting

Green : Normal Operation

Alarm IO Terminal

AI: Alarm Input, G: Ground, AO: Alarm Output

• Extension Cable

Wire Colour

Description

Red: DC12V

White: GND

Main Power, 2pin terminal, DC12V 500mA(6.0W)

Black

Ethernet, RJ-45 port compatible with 10/100Mbps PoE.

Modular Jack

2. Installation

2.1 Connection

• Connecting to the RJ-45

Connect a standard RJ-45 cable to the network port of the network camera. Generally a

cross-over cable is used for directly connection to PC, while a direct cable is used for connection

to a hub.

• Connecting Alarms

AI(Alarm In) :

You can use external devices to signal the VK2-1080VFD3V9 to react on events. Mechanical or

electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors in the bottom.

G(Ground) :

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.

Alarm Out :

The VK2-1080VFD3V9 can activate external devices such as buzzers or lights. Connect the device

to the AO (Alarm Out) and G (Ground) connectors.

• Connecting Alarms

AI(Alarm In) :

You can use external devices to signal the dome camera to react on events. Mechanical or

electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors.

G(Ground) :

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.

AO(Alarm Out) :

The dome camera can activate external devices such as buzzers or lights. Connect the device to

the AO (Alarm Out) and G (Ground) connectors.

• Connecting the Power

Connect the power of DC12V 500mA for the network camera. Connect the positive(+) pole to the

‘+’ position and the negative(-) pole to the ‘-‘ position.

• Connecting Service Monitor Port

Service monitor output port (J5) is located on the board of the dome camera, and is used for an

easy OSD setup.

▶ID & IP assignment

To make changes in the OSD menu, please the OSD controller provided optionally with your

camera purchase. You can set Camera Title and IP Address.

1. Connect the OSD Controller to the Service Monitor port of the network camera.

2. Connect Service Monitor and the Video Output port of the OSD Controller.

3. Press the SET button to access main Menu.

4. Change Camera ID, and IP Address. You can change the Name or Title and IP address of the

camera. Using the buttons on the controller, you can change the parameters.

5. Select SAVE or CANCEL to exit the Main Menu.

Video Output is used for an easy zoom and focus control when installing lens. Video Output is

restricted to 704x480(576) resolution.

▶Zoom & Focus Control

The camera enters Zoom and Focus control mode as soon as connecting OSD Controller to the

Service Monitor port.

-. Zoom Control:

-. Focus Control:

-. Smart Focus: Press and hold the SET button for 2 or more seconds. The camera readjusts

focus automatically.

Note: You can get the Optional OSD Controller from Norbain SD Ltd.

2.2 Network Connection and IP assignment

The VK2-1080VFD3V9 supports the operation through the network. When a camera is first connected

to the network it has no IP address. So, it is necessary to allocate an IP address to the device with the

“Smart Manager” utility on the CD. The factory default IP is “192.168.30.220”.

1. Connect the VK2-1080VFD3V9 to the network and power up.

2. Start SmartManager utility (Start>All programs>Smart Manager>SmartManager), the main

window will be displayed, after a short while any network devices connected to the network will

be displayed in the list.

3. Select the camera on the list and click right button of the mouse. You can see the pop-up menu

as below.

4. Select Assign IP. You cam see a Assign IP window. Enter the required IP address.

Note:For more information, refer to the Smart Manger User’s Manual.

3. Operation

The VK2-1080VFD3V9can be used with Windows operating system and browsers. The recommended

browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome with Windows.

3.1 Access from a browser

1. Start a browser (Internet Explorer).

2. Enter the IP address or host name of the VK2-1080VFD3V9in the Location/Address field of your

browser.

3. You can see a starting page. Click Live View or Setup to enter web page.

4. The encoder’s Live View page appears in your browser.

3.2. Access from the internet

Access from the internet Once connected, the VK2-1080VFD3V9 is accessible on your local network

(LAN). To access the video encoder from the Internet you must configure your broadband router to

allow incoming data traffic to the video encoder. To do this, enable the NAT-traversal feature, which

will attempt to automatically configure the router to allow access to the video encoder. This is enabled

from Setup > System > Network > NAT.

For more information, please see “3.5.4 System>Network>NAT” of User’s Manual.

3.3 Setting the admin password over a secure connection

To gain access to the product, the password for

the default administrator user must be set. This

is done in the “Admin Password” dialog, which is

displayed when the VK2-1080VFD3V9is accessed

for the setup at the first time. Enter your admin

name and password, set by the administrator.

Note: The default administrator username and

password is “admin”. If the password is lost, the

VK2-1080VFD3V9must be reset to the factory

default settings. See “3.6 Resetting to the Factory

Default Settings”.

3.4 Live View Page

The live view page comes in several

screen modes like 1920x1080,

1280x1024, 1280x720, 704x480(576),

640x480, 352x240(288), and

320x240. Users are allowed to select

the most suitable one out of those

modes. Please, adjust the mode in

accordance with your PC

specifications and monitoring

purposes.

1) General controls

Live View Page Search & Playback Page Setup Page Help Page

The video drop-down list allows you to select a customized or pre-programmed

video stream on the live view page. Stream profiles are configured under Setup > Basic

Configuration > Video & Image. For more information, please see “3.5.1 Basic Configuration >

Video & Image” of User’s Manual.

The resolution drop-down list allows you to select the most suitable one

out of video resolutions to be displayed on live view page.

The protocol drop-down list allows you to select which combination of

protocols and methods to use depends on your viewing requirements, and on the properties of

your network.

2) Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following

buttons:

The Stop button stops the video stream being played. Pressing the key again toggles the

start and stop. The Start button connects to the VK2-1080VFD3V9or start playing a

video stream.

The Pause button pause the video stream being played.

The Snapshot button takes a snapshot of the current image. The location where the

image is saved can be specified.

The digital zoom activates a zoom-in or zoom-out function for video image on the live

screen.

The Full Screen button causes the video image to fill the entire screen area. No other

windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full

screen view.

The Manual Trigger button activates a pop-up window to manually start or stop the event.

The Remote Focus button enables users to adjust focus and zoom remotely via network.

The Smart Focus button readjusts focus automatically.

3) Video Streams

The video encoder provides several images and video stream formats. Your requirements and the

properties of your network will determine the type you use.

The Live View page in the video encoder provides access to H.264, MPEG-4 and Motion JPEG

video streams, and to the list of available video streams. Other applications and clients can also

access these video streams/images directly, without going via the Live View page.

Inhaltsverzeichnis

Andere Vista Sicherheitskamera Handbücher

Vista

Vista ViP2 VK2-1080VFD Bedienungsanleitung

Vista

Vista VK2-3MPMD26e Bedienungsanleitung

Vista

Vista VK2-108VRDIR35V16e Bedienungsanleitung

Vista

Vista VK-C402DN Bedienungsanleitung

Vista

Vista Onvif VK2-1080XPTZ Bedienungsanleitung

Vista

Vista VK2-HD20-SM Bedienungsanleitung

Vista

Vista VPL7-WP-SM Leitfaden

Vista

Vista VPC5-704DNS Bedienungsanleitung

Vista

Vista VK2-1080BIR37e Bedienungsanleitung

Vista

Vista VA Series Bedienungsanleitung

Vista

Vista ViP2 VK2-1080VFD Bedienungsanleitung

Vista

Vista VVRD28V12MHDAW Bedienungsanleitung

Vista

Vista PowerDome Series Bedienungsanleitung

Vista

Vista VBC-800NI30-WC Bedienungsanleitung

Vista

Vista VK2-1080BIR37e Bedienungsanleitung

Vista

Vista VK2-12MP360EXTIR Bedienungsanleitung

Vista

Vista VK2-5MPBIR36V10Re Bedienungsanleitung

Vista

Vista VVRD4V9DN Service-Handbuch

Vista

Vista VVRD28V12DN-650 Bedienungsanleitung

Vista

Vista VK2-1080XVRDPTPMF Bedienungsanleitung

Vista

Vista VK2-108VRDIR37e Bedienungsanleitung

Vista

Vista VK2-HD30IR-PM Bedienungsanleitung

Vista

Vista VBC400-600 Bedienungsanleitung

Vista

Vista VK2-108VRDIR35V16e Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung