Vista VK2-108VFDIR37e Bedienungsanleitung
Please read this manual thoroughly before use, and keep it handy for future reference.
VK2-108VFDIR37e
Quick Guide
Quick Installation Guide
VK2-1080VFDIR37e Quick guide V1.0
2
Quick Installation Guide
VK2-1080VFDIR37e Quick guide V1.0
3
1. Description
This manual applies to the VK2-1080VFDIR37ee full HD Internal fixed camera with IR illumination.
• Installation Steps
Follow these steps to install the VK2-1080VFDIR37e on your local network (LAN):
1. Check the package contents against the list below.
2. Connect the VK2-1080VFDIR37e
3. Set an IP address.
4. Set the password.
• Package Component
The system comes with the following components:
Camera Unit Installation CD Installation Guide Accessory Kit
• Contents in the installation CD
1. The User’s Manual
2. The SmartManager User’s Manual
3. The VK2-Client User’s Manual
4. The SmartManager Installation software
5. The VK2-Client Installation software
Note: Check the packaging to make sure that you received the complete system, including all
components shown above.
• Connection Cable
Quick Installation Guide
VK2-1080VFDIR37e Quick guide V1.0
4
Camera Dimension
See the diagrams below for the exact dimension
NO
Name
Description
1
Lens
Allows wide area to be monitored
2
Power Cable
Cable for Power source (DC 12V)
3
Ethernet Cable
Cable for Ethernet (POE)
Quick Installation Guide
VK2-1080VFDIR37e Quick guide V1.0
5
2. Installation
2.1 Connection
• Camera Installation
Carefully remove the contents from the box, and verify that nothing was damaged in shipment.
1) Mark the screw hole positions on the ceiling or wall surface using the template sheet.
2) Disassemble the camera by removing the dome cover.
3) Mount the camera assembly using the Anchors (x2) and Screws (x2) to the surface of the
ceiling or wall
4) Reassemble the dome cover on the camera assembly. Turn Camera Cover clockwise to complete
installation
Locking Screw
Quick Installation Guide
VK2-1080VFDIR37e Quick guide V1.0
6
Lock clockwise
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the Camera . Generally a cross-over cable
is used for directly connection to PC, while a direct cable is used for connection to a hub or switch.
Micro SD memory slot
Insert the SD memory card.
• Connecting the Power
Connect the DC 12V power adaptor to the camera.
(This connection is not used if using PoE power)
SD memory card
Quick Installation Guide
VK2-1080VFDIR37e Quick guide V1.0
7
2.2 Network Connection and IP assignment
When the camera is first connected to the network it has no assigned IP address. So, it is necessary
to allocate an IP address to the device with the “Smart Manager” utility found on the supplied CD. The
factory default IP is “192.168.30.220”.
1. Connect the Camera to the network and power up.
2. Start SmartManager utility (Start>All programs>SmartManager>SmartManager), the main window
will be displayed, after a short while any network devices connected to the network will be
displayed in the list.
3. Select the camera on the list and click right button of the mouse. You can see the pop-up menu
below.
4. Select Assign IP. will see the "Assign IP Address" window. Enter the required IP address.
Note: For more information, refer to the Smart Manger User’s Manual.
Quick Installation Guide
VK2-1080VFDIR37e Quick guide V1.0
8
3. Operation
The Camera can be used with Windows operating system and browsers. The recommended
browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome with Windows.
3.1 Access from a browser
1. Start a browser. (Internet Explorer) will be used in this example.
2. Enter the IP address or host name of the Camera in the Location/Address field of your browser.
3. You can see a starting page. Click Live View or Setup to enter web page.
4. The Camera ’s Live View page appears in your browser.
3.2. Access from the internet
Access from the internet once connected, the Camera is accessible on your local network (LAN). To
access the Camera from the Internet you must configure your broadband router to allow incoming
data traffic to the Camera . To do this, enable the NAT-traversal feature, which will attempt to
automatically configure the router to allow access to the Camera . This is enabled from Setup >
System > Network > NAT.
For more information, please see “3.5.5 System>Network>NAT” of User’s Manual.
Quick Installation Guide
VK2-1080VFDIR37e Quick guide V1.0
9
3.3 Setting the admin password over a secure connection
To gain access to the product, the password for
the default administrator user must be set. This is
done in the “Admin Password” dialog, which is
displayed when the Camera is accessed for the
setup at the first time. Enter your admin name
and password, set by the administrator.
Note: The default administrator username and
password is “admin”. If the password is lost, the
Camera must be reset to the factory default
settings. See “3.6 Resetting to the Factory
Default Settings”.
3.4 Live View Page
The live view page comes in several screen
modes:1920x1080(1600x1200),1280x1024,
1280x720,704x480(576),640x480,352x240(288)
and 320x240. Users are allowed to select the
most suitable one out of those modes. Please,
adjust the mode in accordance with your PC
specifications and monitoring purposes.
1) General controls
Live View Page Search & Playback Page Setup Page Help Page
The video drop-down list allows you to select a customized or pre-programmed
video stream on the live view page. Stream profiles are configured under Setup > Basic
Configuration > Video & Image. For more information, please see “3.5.1 Basic Configuration >
Video & Image” of User’s Manual.
The resolution drop-down list allows you to select the most suitable one
out of video resolutions to be displayed on live view page.
The protocol drop-down list allows you to select which combination of
protocols and methods to use depending on your viewing requirements, and on the properties of
your network.
Quick Installation Guide
VK2-1080VFDIR37e Quick guide V1.0
10
2) Control toolbar
The live viewer toolbar is available in the web browser page only. It displays the following buttons:
The Stop button stops the video stream being played. Pressing the key again toggles the
start and stop. The Start button connects to the Camera or start playing a video
stream.
The Pause button pause the video stream being played.
The Snapshot button takes a snapshot of the current image. The location where the
image is saved can be specified.
The digital zoom activates a zoom-in or zoom-out function for video image on the live
screen.
The Full Screen button causes the video image to fill the entire screen area. No other
windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full
screen view.
The Manual Trigger button activates a pop-up window to manually start or stop the event.
3) Video Streams
The Camera provides several images and video stream formats. Your requirements and the
properties of your network will determine the type you use.
The Live View page in the Camera provides access to H.264, MPEG-4 and Motion JPEG video
streams, and to the list of available video streams. Other applications and clients can also access
these video streams/images directly, without going via the Live View page.
3.5 Camera Setup
This section describes how to configure the Camera , and is intended for product Administrators, who
have unrestricted access to all the Setup tools; and Operators, who have access to the settings for
Basic, Live View, Video & Image, Event, and System Configuration.
You can configure the Camera by clicking Setup in the top right-hand corner of the Live View page.
Click on this page to access the online help that explains the setup tools
When accessing the Camera for the first time, the
“Admin Password” dialog appears. Enter your admin name
and password, set by the administrator.
Note: If the password is lost, the Camera must be reset
to the factory default settings.
See “3.6 Resetting to the Factory Default Settings”.
Inhaltsverzeichnis
Andere Vista Sicherheitskamera Handbücher
Vista
Vista VVRD28V12MHDAW Bedienungsanleitung
Vista
Vista VK2-1080BIR37e Bedienungsanleitung
Vista
Vista Onvif VK2 Bedienungsanleitung
Vista
Vista ONVIF VK2-4KX30IR-PM Bedienungsanleitung
Vista
Vista VK2-1080BXDNe Bedienungsanleitung
Vista
Vista powerdome pro series Bedienungsanleitung
Vista
Vista 1080BIR35V16e Bedienungsanleitung
Vista
Vista VK2-1080MD37W Bedienungsanleitung
Vista
Vista Onvif VIP2 VK2-720VZMX Bedienungsanleitung
Vista
Vista VPM8420 Bedienungsanleitung
Vista
Vista VK2-3MPVRDIR3V9F Bedienungsanleitung
Vista
Vista VVRDE 700 Bedienungsanleitung
Vista
Vista VK2-108VRDIR35V16e Bedienungsanleitung
Vista
Vista VK2-1080XVRDPTPMF Bedienungsanleitung
Vista
Vista Onvif VK2-1080XPTZ Bedienungsanleitung
Vista
Vista VP-HDA30-PM Bedienungsanleitung
Vista
Vista VFDA28V12HDA Series Bedienungsanleitung
Vista
Vista VFD4V9Me Bedienungsanleitung
Vista
Vista VK2-3MPMD26e Bedienungsanleitung
Vista
Vista VK2-108VRDIR35V16e Bedienungsanleitung
