2 IN 1 WIRELESS AUDIO
TRANSMITTER RECEIVER
Instruction Manual RX in TX in
Power
on/o
Vol - /
Previous Track Vol + /
Next Track
USB
charging
port
1. Product Introduction
This compact wireless 3.5mm audio
adapter lets you manage audio signal
freely according to your needs. All
devices with an AUX 3.5mm audio port
are supported - the possibilities are
limitless!
Receiver mode
When used as a wireless receiver, the
RX-TX-10 transforms any traditional car
or home system with an AUX connection
into a contemporary piece of audio
equipment. Use it in this mode to play
music from a smartphone on your trusty
non-Bluetooth stereo system.
Transmitter mode
As a transmitter, this Bluetooth audio adapter allows you to send audio from a
device with an AUX port to any Bluetooth headphones or set of speakers. Use it in
this mode to cast TV audio to your wireless headset when gaming or
binge-watching your favourite series late at night.
2. Specication
- Bluetooth version: 5.0
- Bluetooth frequency: 2.402-2.480GHz
- Bluetooth protocol support: A2DP and AVRCP
- Support multi-format decoding. MP3, WAV, WMA, APE, FLAC
- Transmission distance: > 20M (open place)
- Charge input voltage: DC 5V
- Power supply: 3.7V
- Power consumption: play in less than 20mA, standby in 0.64 – 4.5mA,
shut down in 2 microamps
- Battery capacity: 200mAh
- Working time: about 3 - 5 hours
- Charging time: 2 hours
- Signal-Noise Ratio: more than 95db
3. Package
- 2 in 1 Wireless Audio Transmitter Receiver
- Instruction Manual
- USB charging cable
- 3.5mm audio cable
4. Charging
The 2 in 1 Wireless Audio Transmitter Receiver has built-in rechargeable battery for
long standby and use time. It is recommended that you fully charge before its
rst-time use.
- Plug one end of the Micro USB charging cable into the 2 in 1 Wireless Audio
Transmitter Receiver charging port. The other end plugs into any standard USB
power outlet (such as the phone charger, computer USB interface).
- Charging time is approximately 2 hours
- The red light is on when charging. The red light is o after fully charged.
- Music transmission is still available when charging.
Receiving mode:
- Connect to your Non-wireless speaker or headphones to the 2 in 1 Wireless
Audio Transmitter Receiver RX audio in port via 3.5mm audio jack.
- Hold Down the power On/O button to turn on the 2 in 1 Wireless Audio
Transmitter Receiver.
- Place the 2 in 1 Wireless Audio Transmitter and the Bluetooth device that you
would like to pair within the operating distance. We recommend keeping the
two devices no further than 10 feet apart.
- Ensure Bluetooth is enabled on your phone or music device. Refer to the
manufacturer’s instructions for how to enable Bluetooth on your device.
- Once you have activated Bluetooth on your device, select the “RX-TX-10”from
the list of available Bluetooth devices.
Transmitting mode:
- Connect to your sound or music source to the 2 in 1 Wireless Audio Transmitter
Receiver TX audio in via 3.5mm audio jack.
- Turn on the music source device.
- Hold down the power On/O button to turn on the 2 in 1 Wireless Audio
Transmitter Receiver.
- To activate the transmitter mode, press Vol + and Vol - buttons at the same time
upon powering on the device.
- Turn on your Bluetooth device, ensure it is in pairing mode.
- 2 in 1 Wireless Audio Transmitter Receiver will automatically connect with your
Bluetooth device.
In Receiving mode:
You can Hold down + or - to adjust the volume.
Short press + for next track or - for previous track.
5. Operation
Printed in China
2AUIF-NV-07001
Front100 x 150 mm Back
Instruction Manual
