Vitek VT-8237 Bedienungsanleitung

Фен-щётка

VT-8237

Hot air styler

IM VT-8237_70x130.indd 1 05.06.2018 17:37:43

IM VT-8237_70x130.indd 2 05.06.2018 17:37:44

ENGLISH

HOT AIR STYLER VT-8237

The hot air styler is used for styling dry or slightly wet hair.

DESCRIPTION

Attachment installation place

Attachment release button

Operation mode switch «0-1-2-С»

Body

Air inlet grid

Hanging loop

Thermal brush 40 mm in diameter

Thermal brush with pullout teeth 30 mm in diameter

Concentrator nozzle

ATTENTION!

•

Do not use the unit near containers filled with water

(such as bath, swimming pool etc.) and in rooms with

high humidity.

•

After using the unit in a bathroom, unplug it by taking

the power plug out of the mains socket, as closeness

of water is dangerous even if the unit is switched off.

•

For additional protection you may install a residual cur-

rent device (RCD) with nominal operation current not

exceeding 30 mA into the bathroom mains; contact a

specialist for installation.

SAFETY MEASURES

Before using the unit, read this manual carefully and keep it

for future reference.

Use the unit for intended purposes only, as specified in

this manual. Mishandling the unit can lead to its breakage

and cause harm to the user or damage to his/her property.

•

Before switching the hot air brush on, make sure that

your home mains voltage corresponds to the unit oper-

ating voltage.

•

To avoid fire, do not use adapters for connecting the

unit to the mains.

•

Do not use the unit outdoors.

•

Use only the attachments supplied.

•

When using the unit, we recommend to unwind the

power cord to its full length.

•

The power cord may not:

–

touch hot objects,

IM VT-8237_70x130.indd 3 05.06.2018 17:37:44

ENGLISH

–

run over sharp edges,

–

be used for carrying the unit.

•

Check the power cord and power plug insulation integ-

rity periodically.

•

Do not switch the unit on in places where aerosols are

sprayed or highly flammable liquids are used.

•

Hair spray shall be applied only after hair styling is fin-

ished.

•

Do not operate the unit while taking a bath.

•

Never leave the operating unit unattended.

•

Do not touch the unit body, the power cord and power

plug with wet hands.

•

Do not place and do not keep the unit in places, where

it can fall into a bath or a sink filled with water, do not

immerse the unit into water or other liquids.

•

If the unit is dropped into water, unplug it immediately,

and only then take it out of the water.

•

Do not use the unit when you are drowsy.

•

Do not use the unit to style wet hair or synthetic wigs.

•

Avoid contact of heated surfaces with your face, neck

and other parts of your body.

•

Do not drop the unit.

•

Do not direct hot air into your eyes or other heat-sensi-

tive parts of your body.

•

The attachments get hot during use. Allow them to cool

down before removal.

•

Never insert any foreign objects into any unit body

openings.

•

Never block the air inlets of the hot air brush,

do not place it on a soft surface (a bed or sofa), where

the air inlets may be blocked. Keep the air inlets free of

lint, dust and hair etc.

•

Clean the unit regularly.

•

Unplug the unit after every usage and before cleaning.

•

When unplugging the unit, pull the power plug but not

the power cord.

•

For children safety reasons do not leave polyethylene

bags used as packaging unattended.

ATTENTION! Do not allow children to play with polyethylene

bags or packaging film. Danger of suffocation!

•

Do not allow children to touch the unit body, the power

cord or the power plug during operation of the unit.

IM VT-8237_70x130.indd 4 05.06.2018 17:37:44

ENGLISH

•

Do not leave children unattended to prevent using the

unit as a toy.

•

Close supervision is necessary when children or dis-

abled persons are near the operating unit.

•

This unit is not intended for usage by children. Place the

unit out of reach of children during the operation and

cooling down.

•

The unit is not intended for usage by physically or men-

tally disabled persons (including children) or by persons

lacking experience or knowledge if they are not under

supervision of a person who is responsible for their

safety or if they are not instructed by this person on the

usage of the unit.

•

Do not attempt to repair the unit. Do not disassemble

the unit by yourself, if any malfunction is detected or

after it was dropped, unplug the unit and apply to any

authorized service center from the contact address

list given in the warranty certificate and on the website

www.vitek.ru .

•

To avoid damages, transport the unit in the original

package only.

•

Keep the unit in a dry cool place out of reach of children

and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY,

ITS COMMERCIAL USAGE AND USAGE IN PRODUCTION

AREAS AND WORK SPACES IS PROHIBITED.

BEFORE THE FIRST USE

After unit transportation or storage at low temperature

keep it for at least three hours at room temperature

before switching on.

•

Unpack the hot air styler and remove any stickers that

can prevent unit operation.

•

Unwind the power cord completely.

•

Install one of the attachments (7), (8) or (9). To do this

insert the brush attachment into the installation place (1)

and turn it clockwise. If the attachment is set properly,

you will hear the release button (2) click.

•

Before switching the unit on, make sure that your

home mains voltage corresponds to the unit operat-

ing voltage.

IM VT-8237_70x130.indd 5 05.06.2018 17:37:44

ENGLISH

USING THE HOT AIR BRUSH

•

Make sure that the operation mode switch (3) is set to

the position “0”.

•

Insert the power plug into the mains socket.

•

Set the required settings of the air flow using the

switch (3):

«0» – the hot air brush is switched off;

«1» – low air flow speed and low temperature;

«2» – high air flow speed and high temperature;

«С» – «cool» air supply

Note: During the first operation some foreign smell and a

small amount of smoke from the heating element is pos-

sible, it is normal.

•

You can move out or remove the thermal brush (8)

teeth; wind a lock of hair around the brush (8), wait a

bit and turn the tip (7) counterclockwise (the teeth will

be removed into the brush), take the brush (8) out of

the hair.

•

After the hot air brush operation is finished, switch it off

by setting the switch (3) to the «0» position and unplug it.

•

Wait till the hot air brush cools down.

•

To remove the attachment, shift to the right and hold

down the attachment release button (2), and turn the

attachment counterclockwise.

•

Periodically straighten the cord if it gets twisted during

hairdryer operation.

Overheating protection

Overheating protection switches the hot air styler off if the

temperature of the outgoing air is above the limit. If the hot

air styler is switched off during operation, set the switch (3)

to the “0” position, unplug the unit and make sure that the

inlets and outlets are not blocked. Let the unit cool down

for 5-10 minutes and switch it on again. Do not block the air

inlets during the hot air styler operation and avoid getting

hair into its air inlet (5).

CLEANING AND CARE

The нot air brush is intended for household use only.

•

Set the switch (3) to the «0» position, disconnect the hot

air brush from the mains and let it cool down.

IM VT-8237_70x130.indd 6 05.06.2018 17:37:44

ENGLISH

•

To remove the attachment, shift to the right and hold

down the attachment release button (2), and turn the

attachment counterclockwise.

•

Wipe the unit body (4) with a damp cloth and then wipe

it dry.

•

Clean the air inlet grid (5) with a brush.

•

Never immerse the unit into water or other liquids.

•

Do not use abrasives and solvents to clean the unit

body.

STORAGE

•

Disconnect the unit from the mains and clean it.

•

Never wind the power cord around the hot air brush,

as this can damage the cord or the unit body. Handle

the power cord with care, do not pull, twist or stretch it,

especially near the power plug or at the junction point.

Straighten the cord periodically if it gets twisted during

the hot air brush operation.

•

For easy storing there is a hanging loop (6), you can

hang the hot air styler on this loop provided that no water

gets on the unit in this position.

•

Keep the unit in a dry cool place out of reach of children

and disabled persons.

DELIVERY SET

Hot air styler – 1 pc.

Thermal brush with pullout teeth 30 mm – 1pc.

Thermal brush 40 mm in diameter – 1 pc.

Concentrator nozzle – 1 pc.

Manual – 1 pc.

TECHNICAL SPECIFICATIONS

Power supply: 220-240 V ~ 50 Hz

Rated input power: 1000-1200 W

ATTENTION! Do not use the unit near water in the bath-

rooms, showers, swimming pools etc.

IM VT-8237_70x130.indd 7 05.06.2018 17:37:44

ENGLISH

RECYCLING

For environment protection do not throw out the unit and

the batteries (if included), do not discard the unit and the

batteries with usual household waste after the service life

expiration; apply to specialized centers for further recycling.

The waste generated during the disposal of the unit is sub-

ject to mandatory collection and consequent disposal in the

prescribed manner.

For further information about recycling of this product apply

to a local municipal administration, a disposal service or to

the shop where you purchased this product.

The manufacturer reserves the right to change design, struc-

ture and specifications not affecting general principles of the

unit operation without a preliminary notification due to which

insignificant differences between the manual and product

may be observed. If the user discovers such inconsisten-

cies, please report them via e-mail [email protected] to receive

an updated manual.

Unit operating life is 3 years

Guarantee

Details regarding guarantee conditions can be obtained

from the dealer from whom the appliance was purchased.

The bill of sale or receipt must be produced when making

any claim under the terms of this guarantee.

This product conforms to the EMC Directive

2014/30/EU and to the Low Voltage Directive

2014/35/EU.

IM VT-8237_70x130.indd 8 05.06.2018 17:37:45

русский

ФЕН-ЩЁТКА VT-8237

Фен-щётка используется для укладки сухих или слегка

влажных волос.

ОПИСАНИЕ

Место установки насадок

Клавиша-фиксатор насадок

Переключатель режимов работы «0-1-2-С»

Корпус

Воздухозаборная решётка

Петелька для подвешивания

Термощётка диаметром 40 мм

Термощётка с выдвижными зубьями

диаметром 30 мм

Насадка-концентратор

ВНИМАНИЕ!

•

Не используйте устройство вблизи ёмкостей с водой

(таких как ванна, бассейн и т.п.), а также в помеще-

ниях с повышенной влажностью.

•

После использования устройства в ванной ком-

нате отключите его от электрической сети, вынув

вилку сетевого шнура из электрической розетки,

так как близость воды представляет опасность

даже в тех случаях, когда устройство выключено

выключателем.

•

Для дополнительной защиты в цепи питания ван-

ной комнаты целесообразно установить устройство

защитного отключения (УЗО) с номинальным током

срабатывания, не превышающим 30 мА; при уста-

новке следует обратиться к специалисту.

МЕРЫ БЕЗОПАСНОСТИ

Перед началом эксплуатации электроприбора внима-

тельно прочитайте настоящее руководство и сохра-

ните его для использования в качестве справочного

материала.

Используйте устройство только по его прямому назначе-

нию, как изложено в данном руководстве. Неправильное

обращение с прибором может привести к его поломке,

причинению вреда пользователю или его имуществу.

•

Перед включением фена-щётки убедитесь в том,

что напряжение электрической сети соответствует

рабочему напряжению устройства.

IM VT-8237_70x130.indd 9 05.06.2018 17:37:45

русский

•

Во избежание пожара не используйте переходни-

ки при подключении устройства к электрической

розетке.

•

Не используйте устройство вне помещений

•

Применяйте только насадки, которые входят в ком-

плект поставки.

•

При эксплуатации прибора рекомендуется размо-

тать сетевой шнур на всю длину.

•

Сетевой шнур не должен:

– соприкасаться с горячими предметами,

– протягиваться через острые кромки,

– использоваться для переноски прибора.

•

Периодически проверяйте состояние изо-

ляции сетевого шнура и сетевой вилки.

•

Не включайте устройство в местах, где распыляются

аэрозоли или используются легковоспламеняющи-

еся жидкости.

•

Наносите лак для волос только после моделирова-

ния причёски.

•

Не используйте прибор во время принятия ванны.

•

Никогда не оставляйте работающий прибор без при-

смотра.

•

Не беритесь мокрыми руками за корпус, сетевой

шнур и вилку сетевого шнура.

•

Не кладите и не храните устройство в местах, где оно

может упасть в ванну или раковину, наполненную

водой, не погружайте устройство в воду или в любую

другую жидкость.

•

Если устройство упало в воду, немедленно извлеки-

те сетевую вилку из электрической розетки, и только

после этого можно достать прибор из воды.

•

Не используйте устройство, если вы находитесь в

сонном состоянии.

•

Не используйте прибор для укладки мокрых волос

или синтетических париков.

•

Избегайте соприкосновения горячих поверхностей

устройства с лицом, шеей и другими частями тела.

•

Не роняйте устройство.

•

Не направляйте горячий воздух в глаза или на другие

теплочувствительные части тела.

•

Насадки во время работы нагреваются. Перед их

снятием дайте им остыть.

•

Не вставляйте посторонние предметы в любые

отверстия корпуса.

IM VT-8237_70x130.indd 10 05.06.2018 17:37:45

Inhaltsverzeichnis

Sprachen:

Andere Vitek Haarstylinggerät Handbücher

Vitek

Vitek VT-8433 Bedienungsanleitung

Vitek

Vitek VT-2297 Bedienungsanleitung

Vitek

Vitek VT-1330 Bedienungsanleitung

Vitek

Vitek VT-8244 Bedienungsanleitung

Vitek

Vitek VT-8240 Bedienungsanleitung

Vitek

Vitek Curly lady Bedienungsanleitung

Vitek

Vitek VT-8246 Bedienungsanleitung

Vitek

Vitek VT-1315 Bedienungsanleitung

Vitek

Vitek VT-8243 Bedienungsanleitung

Vitek

Vitek VT-8236 Bedienungsanleitung

Vitek

Vitek VT-2296 BK Bedienungsanleitung

Vitek

Vitek VT-8238 VT Bedienungsanleitung

Vitek

Vitek VT-8235 VT Bedienungsanleitung

Vitek

Vitek VT-1326 Bedienungsanleitung

Vitek

Vitek VT-1327 Bedienungsanleitung

Vitek

Vitek VT-8245 Bedienungsanleitung

Vitek

Vitek VT-8238 Bedienungsanleitung

Vitek

Vitek VT-1324 Bedienungsanleitung

Vitek

Vitek VT-8240 BN Bedienungsanleitung

Vitek

Vitek VT-8242 Bedienungsanleitung

Vitek

Vitek VT-2533 VT Bedienungsanleitung

Vitek

Vitek VT-8241 Bedienungsanleitung

Vitek

Vitek VT-2285 Bedienungsanleitung

Vitek

Vitek VT-8435 Bedienungsanleitung

Beliebte Haarstylinggerät Handbücher anderer Marken

Philips

Philips HP8309 Bedienungsanleitung

Eldom

Eldom bess HTS20 Bedienungsanleitung

Lunata Hair

Lunata Hair LH24HR Originalbetriebsanleitung

Conair

Conair S3CSC Bedienungsanleitung

Remington

Remington CI89H1 Bedienungsanleitung

Dyson

Dyson Airwrap Bedienungsanleitung

Braun

Braun Satin Hair 1 AS 110 Kurzanleitung

REVAMP Professional

REVAMP Professional iGEN PROGLOSS CL-2750 Bedienungsanleitung

point

point WAVE VIXEN TRIPLE WAVE MAKER Bedienungsanleitung

Braun

Braun Satin Hair 5 Bedienungsanleitung

Philips

Philips beauty Airstylist quattro 600 Bedienungsanleitung

Grundig

Grundig HS 7230 Bedienungsanleitung

Philips

Philips HP4658/08 Bedienungsanleitung

Remington

Remington AS7100 Bedienungsanleitung

HOT TOOLS

HOT TOOLS SIGNATURE Series Installationsanleitung

Conair

Conair INFINITI INFCS25C Bedienungsanleitung

Philips

Philips Norelco RQ111 Stücklistenhandbuch

Clas Ohlson

Clas Ohlson 44-1152 Bedienungsanleitung