Vitek STARLIGHT VTC-IRM30-2812 Bedienungsanleitung
FEATURES:
• 1/2.8” Sony® STARVIS 2.1 MegaPixel CMOS Sensor
• 2.1 MegaPixel with Full 1080p/720p HD/EX-SDI 1.0, 2.0 / TVI / AHD / CVI
/ CVBS Output
• Advanced Starlight Technology Offers Dramatically Higher Sensitivity to Light
Producing Color Images in Very Dark & Night Scenes
• MegaPixel IR Corrected 2.8~12mm Motorized Varifocal Lens with 1 click
focus for easy Configuration
• 30 Dynamic Infrared LEDs at 850nm enable viewing in total darkness up to
100 feet
• Dual Glass Compartments to Eliminate IR Reflection
• 3D-DNR Digital Noise Reduction
• True Day/Night by ICR - Dual Filter Switch
• Fully programmable True WDR (Dual Scan)
• ROI (Region of Interest) WDR achieves superior exposure compensation
specifically in exact areas of interest while reducing HDD storage space
• Secondary Video Output & OSD Control Joystick are accessible inside a
gasket sealed removable side panel
• Advanced OSD Functions: Motion Detection, Privacy Mask, Defog, Sens-
up(~x32), Sharpness, Mirror/Flip, BLC/HLC, Deblur, Anti-Saturation, Title
Set, D-WDR
• 3-Axis mount with Simple One Turn Positioning Lock for Ease of Installation
• IP-67 Rated Water Resistance
• 12VDC / 24VAC Dual Voltage Operation
VTC-IRM30-2812
Premium 2.1 Megapixel Indoor/
Outdoor 6-in-1 HD/EX-SDI / TVI / AHD
/ CVI / CVBS Motorized Varifocal Bullet
Camera with IR LED Illumination
VITEK
VITEK
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power main interruption, it is
recommended that the model be powered from an uninterruptible power supply
(UPS).
2 3
Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing in areas where shock or vibrations may occur.
Pay attention to safety when running the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to damage and void the warranty.
The camera should never be operated in water.
3
Contents
Safety Precaution
p.02~03
Contents
p.04
Composition
p.05
Dimensions
p.05
Installation Instructions
p.06~09
p.10~26
Operating Instructions
p.27
Specifications
4 5
Composition
Dimensions
Torque Wrench:
3mm (1pc)
Video Sub-out:
Cable (1pc)
Mounting Screw:
4 x 40mm (3pcs)
Plastic Anchor:
6 x 30mm (3pcs)
Mounting
Template
Operating
Instruction
Camera
3.17”
3.73”
3.43”
3.64”
9.72”
9.29”
5
Part Names
DUAL WINDOW
POWER
CABLE
SUNSHIELD BOLT
SUNSHIELD
FRONT CASE
OSD Setup
CONTROL COVER
BRACKET
REAR CASE
• Extreme care should be taken NOT to scratch the window in front of lens.
• Care should be taken that the cable is not damaged, kinked or exposed in
hazardous areas.
• Do not expose the camera directly to a strong light source such as the sun or
spotlight.
CAUTION
6 7
Installation Instructions
1. Locate the mounting template at the installation position and drill the ceiling
or wall if needed.
2. Route the Power cable to the connecting place.
3. Place the camera bracket on pre-drilled position and attach it using
mounting screws (4x40mm).
4. Set the camera’s viewing angle by using the L-wrench.
5. Put the sunshield onto the camera unit and tighten the sunshield-bolt.
Mounting Screw
: 4x40mm
■Adjustment of viewing angle
with one-touch 3-Axis bracket
Torque
wrench
Lock/Unlock
Screw
6 7
Installation Instructions
Pan & Tilt adjustments
1) Pan limit:
Pan is limited to +/- 90°.
3) Inclination limit
(Horizontal image alignment):
Inclination limited to +/-90° max.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively
with reference to the wall(ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.
90° 90°
• Unlock the screw on the camera bracket through using the torque wrench
supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
90°
90°
±90°
•on the wall •on the ceiling
8 9
Installation Instructions
Installation Instructions
• Make sure power is removed before the installation.
• Follow the order for applying power:
Connect the power leads to the camera (observe polarity for DC power) then
plug-in power. This will avoid damage to the camera from power surges and
improper reseting .
Power Supply Connections
Camera can work with either 12VDC or 24VAC, dual voltage power. Primary
and secondary grounds are completely isolated to avoid the possible ground-loop
problems.
※SDI OUTPUT
(Yellow)
ANALOG OUTPUT
(Black)
POWER
(AC24V/DC12V)
▪ AC(-) :
AC24V/GND
▪AC(+) :
AC24V/DC12V
AC
(+)
AC
(-)
※Please use the cable as provided with camera. If camera cable is cut
and re-wired, the transmission distance of video can be reduced.
Especially SDI cable should not be cut because it requires detailed
wiring and affects the transmission distance.
8 9
Operating Instructions
Setup menu can be accessed and controlled by OSD control joystick on
the side of the camera. Five commands are available with the joy stick.
The design of OSD could be different according to the Model.
Using OSD Controller
Cover Open
Video Sub-out
Connector
OSD Control Joy Stick
SUB-OUT
ZOOM
1] SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down.
2] UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.
3] LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu. Used
to adjust the desired menu selection and to move the cursor left or right.
Description of the OSD control operation
Description of the Motorized ZOOM&FOCUS* adjustment
1) ▲: Zoom In
2) ▼ : Zoom Out
3) ◄: Focus Near
4) ► : Focus Far
(*) Works only when OSD Menu is inactive.
ANALOG OUT should be set to TVI MODE, AHD MODE or CVI MODE
to get CVBS video in sub-out. If it is set to CVBS, there is no CVBS video
in sub-out port. (SYSTEM> OUTPUT> ANALOG OUTPUT0)
If CVBS video is enabled through ANALOG OUT or Sub-out port, WDR
and 3D-NR functions are disabled in all video outputs.
It should be considered when installer adjusts the video with installation
monitor via CVBS video signal.
10 11
Inhaltsverzeichnis
Andere Vitek Sicherheitskamera Handbücher
Vitek
Vitek Virtuoso Series 5 Bedienungsanleitung
Vitek
Vitek VTC-C01 Bedienungsanleitung
Vitek
Vitek VTD-A4F Bedienungsanleitung
Vitek
Vitek VT-PIRC2 Bedienungsanleitung
Vitek
Vitek Transcendent Series Bedienungsanleitung
Vitek
Vitek VTD-VS48B2 Bedienungsanleitung
Vitek
Vitek TRANSCENDENT VTC-TNB8FADW-2 Bedienungsanleitung
Vitek
Vitek TRANSCENDENT VTD-TND3RVEB Bedienungsanleitung
Vitek
Vitek TRANSCENDENT VTD-T4D6HR5MD Bedienungsanleitung
Vitek
Vitek VTD-C75 Bedienungsanleitung
Vitek
Vitek VTC-C770DN/IP2 Bedienungsanleitung
Vitek
Vitek VTD-M2HET2812 Bedienungsanleitung
Vitek
Vitek VTC-LED697HRCB Bedienungsanleitung
Vitek
Vitek VTC-IRH70 Bedienungsanleitung
Vitek
Vitek TRANSCENDENT VTD-TND5RME Bedienungsanleitung
Vitek
Vitek VTC-C960DS Bedienungsanleitung
Vitek
Vitek VTD-MV-VN Bedienungsanleitung
Vitek
Vitek Mighty Series Bedienungsanleitung
Vitek
Vitek VTC-C661 Bedienungsanleitung
Vitek
Vitek VTC-IRM40-2812 Bedienungsanleitung
