Vitek VTC-C2B-HS Bedienungsanleitung

FEATURES:

• 1/2.9” Sony CMOS

• 2.1 MegaPixel With full 1080p/720p HD-SDI

Output (SMPTE 292M)

• Smart Motion Zoom tracks motion, then

intelligently zooms into that area of the frame

• Mechanical IR Cut Filter (True Day/Night)

• Small scale design to fit in 5” dome enclosures

such as the Pelco DF5 Housing

• Fully programmable advanced WDR

• Sensitivity of 0.0005 Lux

• Advanced OSD Functions: Defog, BLC/HLC,

Motion Deblur, Pixel Defect Compensation,

Mirror, Flip

• 100% Pure Digital Transmission of video data

• Up to 700’ HD Transmission Range (Depending

on cable characteristics and integrity)

• 12VDC / 24VAC Dual Voltage Operation

VTC-C2B-HS

2.1MP HD-SDI Smart

WDR Camera

VITEK

Safety Precaution

FULL-HD MEGA-PIXEL CAMERA

CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To prevent electric shocks and risk of fire hazards, do NOT use other than

specific power source.

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

Caution :

Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority

to operate the equipment.

Mains power quality should be that of a typical commercial environment. If the user

of the model requires continued operation during power mains interruptions, it is

recommended that the model be powered from an uninterruptible power supply

(UPS) or a battery.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

FULL-HD MEGA-PIXEL CAMERA

Safety Precaution

NOTICE

The image used in this instruction manual are processed to help comprehension

and may differ from actual video of the camera.

Avoid installing in areas where shock or vibration may occur.

Pay attention to safety when running the connection cable and observe that the cable

is not subjected to heavy loads, kinks or damage and no moisture can get in.

Never open the device.

The warranty becomes void if repairs are undertaken by unauthorized persons.

Maintenance and repair have to be carried out only by authorized service centers.

Use only a mild detergent to clean the housing.

The camera should never be operated beyond the technical specifications.

This can lead to damaging the camera and voiding the warranty.

The camera should never be operated in water.

FULL-HD MEGA-PIXEL CAMERA

Contents

Safety Precaution

p.02~03

Contents

p.04

Features

p.05

Composition

p.06

Dimensions

p.06

Part Names

p.07

Installation Instructions

p.08~09

Operating Instructions

p.10~22

Specifications

p.23

FULL-HD MEGA-PIXEL CAMERA

Features

Key Features

• Full HD, 2Mega Pixel HD-SDI CAMERA, 1920x1080(30p/25p)

• True WDR(Wide Dynamic Range)

• Improved Noise filter with the enhanced 3D-NR

• CS mount supported (Option: C-mount adaptor)

• Non Compressed digital streaming up to 1.485Gbps.

• Intelligent focusing status indicator on screen

• Dual Filter Switcher

• Pointing Zoom which enables the flexible zooming of any area.

• Smart Motion Zoom in combination with Pointing Zoom.

• Selectable Scale down or Cropped image to 720p mode

• Motion Detection, Privacy Mask, Defog, Sens-up(x32), D-WDR,

H/V/HV Flip, D-Zoom(1.1x~8x), LSC(Lens Shade Compensation),

BLC/HLC, Motion Deblur, Pixel Defect Compensation, Title Set

• Back focus Flange

• Top performance at low light sensitivity (Sens-up On)

•OSD menu & CVBS Video output BNC for easy installation & maintenance.

• Circuit protection against reverse power polarity

• Isolated power supply to help avoid ground loop problem

• Remote control via RS-485 (Pelco-D/P)

General Description

• With ICR mechanism,

- Enhances its sensitivity about 10x at night time

- Can accept infrared light

• With Intelligent Focus Indicator and FOCUS ASSIST menu,

- Offers easy adjustment of Focus

• With 24VAC/12VDC dual power design,

- Offers flexibility of installation

This camera incorporates a full (1920 x 1080p) HD camera module.

FULL-HD MEGA-PIXEL CAMERA

L- Wrench:

1.5mm (1pc)

Dust Protection

Cap (1pc)

(unit : inches)

Operating

Instruction

Compact Box Camera

Dimensions

Composition

Video Sub-out

Cable (1pc)

2.38

2.09

1.73

1.89

2.87

1.81

FULL-HD MEGA-PIXEL CAMERA

Part Names

L-Wrench

Dust

Protection Cap

No.

DC Iris

Damp(-)

Damp(+)

Drive(+)

GND

Flange Lock screw

Front Case

Rear Case

Back focus

adjusting Flange

Mount Holes

(Top / Bottom)

REAR VIEW

Lens Connector

for Auto Iris lenses

① Video out connector(BNC)

② Power input terminal

③OSD Control Joy stick

④ DC Auto Iris Lens connector

④

③

①

②

PIN 1PIN 3

PIN 2PIN 4

Installation Instructions

1. Remove the dust protection cap from the lens mount.

2. Screw the lens onto the camera firmly (do not over tighten).

3. Plug the lens into the lens connector on the rear of camera case.

4. Mount the camera to the wall or ceilling with a corresponding mounting bracket

through the camera mount holes (1/4” thread insert) on its top or bottom.

CAUTION

Installation and commissioning Instructions

• Make sure the power is removed before installation.

• Follow the order for applying power.

When using 12VDC or 24VAC power make power connections

at camera first then apply power. this will help avoid unnecessary

power surges to camera.

• Care should be taken the cable is NOT damaged, kinked or exposed in

any hazardous area.

• Do not expose the camera lens directly to a strong light source such as the sun or

spot light.

Setting the back focus adjustment

For easier and better adjustment, this camera provides FOCUS ADJUST menu

which will assist you in the focusing of the camera.

When enabling FOCUS ASSIST menu, follow the procedure to get the best back

focus adjustment.

1. Set the lens for the zoom position to WIDE and the focus position to INFINITE(∞).

2. Point the camera at an object about 30' away

3. Adjust ’Back focus adjusting Flange’ until the optimum focus is achieved.

4. Set the lens zoom position to TELE and adjust the lens focus for best focus.

5. Set the lens zoom position to WIDE again, check if the focus adjustment

was the best. If not, re-adjust ‘Back focus Flange’ slightly.

6. After the setting, tighten the ‘Flange lock screw’ with L-wrench supplied.

Start up

When the camera is powered properly, it starts up with initializing the internal

parameters.

FULL-HD MEGA-PIXEL CAMERA

Installation Instructions

Using OSD Controller

Setup menu can be accessed and controlled by OSD control joy stick on the rear

of the camera unit.

Five commands are available with the joy stick.

The design of rear panel could be different according to the camera models.

Description of the joystick operation

FULL-HD MEGA-PIXEL CAMERA

1) SET Key (●) : Access to the menu or enter the setting.

To enter the main menu, press the Set Key down for about 2sec

2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move

the cursor up or down.

3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.

Used to adjust the desired menu selection and to move the cursor left

or right.

4) denotes a long press down, for about 2 seconds

Operating Instructions

FULL-HD MEGA-PIXEL CAMERA

OSD menu Startup

Press ‘●’(OSD menu Joy stick key) down for about 2 seconds to access the

setup menu mode.

MENU V3.12

1. EXPOSURE

2. LENS

3. FOCUS ASSIST

4. SCENE ENHANCE

5. 3D-NR

6. DAY/NIGHT

7. PICT ADJUST

8. SPECIAL

9. SYSTEM

A. EXIT

NORMAL

MID

AUTO

SAVE&EXIT

Direct Control menu

MAIN

DEFAULT

DESCRIPTION

LENS

Sets Lens types.

FOCUS ASSIST

Sets FOCUS

EXPOSURE

Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, AGC and

MOTION DEBLUR.

SCENE

ENHANCE

NORMAL SCENE ENHANCE provides several ways to enhance the video

in various environments with settings in NORMAL, WDR,

D-WDR, BLC and HLC.

NORMAL – Optimized for normal indoor and outdoor in good

lighting condition.

WDR – This function extends the gain range of the screen that is

useful if the camera takes a simultaneous picture of both indoor and

outdoor. It improves contrast of the picture in outdoor scenery as well

as indoor. Video image is processed from two images by dual

shutter (long and short shutter) in a field to provide the best dynamic

range. Highlight area is compensated by the short shutter and dark

area is compensated by the long shutter. Final video may have less

contrast compared to the conventional camera which does not have

WDR function."

※CVBS video signal:Connecting 2nd video to CVBS port disables

WDR function temporary. It should be considered when installer

adjusts the video with installation monitor via CVBS video signal.

D-WDR – Improves the visibility by compensating the video gain for

the dark area. Noise can increase in the dark area accordingly.

Inhaltsverzeichnis

Andere Vitek Sicherheitskamera Handbücher

Vitek

Vitek VT-IR1C/24 Bedienungsanleitung

Vitek

Vitek VTD-C75 Bedienungsanleitung

Vitek

Vitek VTD-MVH2910/L35 Bedienungsanleitung

Vitek

Vitek VTC-HOCRBD2812 Bedienungsanleitung

Vitek

Vitek TRANSCENDENT VTC-THT10R2F Bedienungsanleitung

Vitek

Vitek VTC-PIR2 Bedienungsanleitung

Vitek

Vitek VTD-TNMD4RFS Bedienungsanleitung

Vitek

Vitek VTC-BHOCR2812 Bedienungsanleitung

Vitek

Vitek TRANSCENDENT VT-TPTZ4AD-4M Bedienungsanleitung

Vitek

Vitek VTC-TNT5RFE-2 Bedienungsanleitung

Vitek

Vitek VTC-IRE70 Bedienungsanleitung

Vitek

Vitek VTC-C2BAZE Bedienungsanleitung

Vitek

Vitek TRANSCENDENT VTC-TNB48R4M2 Bedienungsanleitung

Vitek

Vitek Transcendent Series Bedienungsanleitung

Vitek

Vitek VTD-TND4RFA4 Bedienungsanleitung

Vitek

Vitek VT-PTZ10 Bedienungsanleitung

Vitek

Vitek VTC-C770/WDR Bedienungsanleitung

Vitek

Vitek VTC-TNT8RMA4 Bedienungsanleitung

Vitek

Vitek VTD-MD2-4 Bedienungsanleitung

Vitek

Vitek VTC-EBV49-24 Bedienungsanleitung

Vitek

Vitek Mighty Series Bedienungsanleitung

Vitek

Vitek VTC-IR62NZ922 Bedienungsanleitung

Vitek

Vitek VTD-TND4RMS Bedienungsanleitung

Vitek

Vitek VTD-VS48 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung