Vitek VTC-C770DN Bedienungsanleitung

BLACKYELLOWMAGENTACYAN

VITEK

VTC-C770DN

700TVL True Day and Night

(ICR) Camera

• 1/3” Sony High Density EXVIEW CCD

• Sony Effio Digital Signal Processor

• 700TVL High Resolution

• .003Lux (F1.2@50IRE)

• Supports C/CS mount DC drive lenses

• Supports NTSC & PAL Standards

• Adaptive Tone Reproduction

• 2DNR - Two Dimensional Motion Adaptive Noise Reduction

• Motion Detection

• Privacy Mask

• On Screen Display (OSD) Menu

• 24VAC/12DC Dual Voltage

VTC-C770DN

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

This symbol is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying the unit.

This symbol is intended to alert the user to the presence of un-insulated "dangerous

voltage" within the product's enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to a person.

Warning (NTSC version) -- This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation

of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at their expense.

Caution -- Any changes or modifications in construction of this device that are not expressly

approved by the party responsible for compliance, could void the user's authority to operate the

equipment.

WARNING

Caution

To prevent electric shocks

and risk of fire hazards, do

NOT use other than specific

power source.

VTC-C770DN

Table of contents

1. Safety Instructions and Notes…......................................................................................................

2. General Descriptions............................................................................……………………………...

3. Supplied Items......................................................................................……………………………...

4. Part names…………………………….…...................................................…………………………...

5. Installation and Commissioning Instructions....................................................……………………...

6. Setup Menu…………………............................................................................……………………...

7. Specifications…………………………………………….....................................................................

8. Dimensional Drawings….................................................................................................................

VTC-C770DN

1. Safety Instructions and Notes

• Read instructions carefully before putting the camera into operation.

• Keep the operating instructions in a safe place for later use.

• The Standard Box Camera is designed for indoor use only and it must not be installed where exposed

to rain and moisture.

• Do not operate the cameras beyond their specified temperature, humidity or power ratings.

• Never open the case of the camera because there are precision parts inside. An accident may result.

• Do not put anything metallic or foreign through the vent. A fire or electric shock may result.

• Be sure to turn off the power before installing or making connection.

• Pay attention when laying the connection cable and observe that the cable is not subject to heavy

loads, kinks or damage and no moisture can get in.

• Do not install the camera in places exposed to vibrations and shocks.

• Be very careful not to drop or shock the camera while carrying it.

• Do not angle the camera to the sun.

• Do not make any modification to the unit (neither to the software nor the hardware). Improper

modification voids the warranty and can cause malfunctions or damages. The manufacturer accepts

no liability for damages resulting from unauthorized or improper modifications to the unit.

• Some types of lenses may cause hunting, light amount drop or other problems. In such case, readjust

the lenses.

• Because of the digital image device characteristics, images may look rugged at high temperatures.

This does not mean the camera is in trouble.

• The warranty becomes void if repairs are attempted by unauthorized persons.

• Contact the supplier if any functional problems arise.

Cleaning:

• Do not touch the surface of the imaging device.

• Keep front and rear lens surfaces clean.

Notice -- The images used in this manual are processed to help comprehension and may differ from

actual video of the camera.

VTC-C770DN

2. General Descriptions

VTC-C770DN (VTC-C770DN/PAL for PAL) is an ultra clear resolution camera that achieves 700TVL

resolution and a crisp color reproduction with the use of Sony 960H EX-view CCD and Effio-E image signal

processor.

With Effio-E digital imaging system,

- Delivers crystal clear images with 700TVL resolution that accurately capture every aspect of any

scene

- Color signal processing provides the optimum balance between the luminance and chroma signals for

high color reproducibility. It even captures detailed scenes that contain very high spatial frequency.

- Incorporates 2-D noise reduction signal processing

With ICR mechanism,

- Enhances its sensitivity about 10x at night

- Accepts infrared light

With 24VAC/12VDC dual power design,

- Offers flexibility of installation

- Ensures reliability

Main features are:

• 1/3" Sony High Density EXVIEW CCD

•Sony Effio Digital Signal Processor

•700TVL High Resolution

•0.003Lux (F1.2@50IRE)

•Supports C/CS mount DC drive lenses

•Supports NTSC & PAL Standards

•Adaptive Tone Reproduction

•2DNR - Two Dimensional Motion Adaptive Noise Reduction

•Motion Detection

•Privacy Mask

•On Screen Display (OSD) Menu

•24VAC/12DC Dual Voltage

3. Supplied Items

1 x ULTRACLEAR RESOLUTION Color Camera

1 x Dust protection cap

1 x Installation and Operating Instructions

VTC-C770DN

③

②

4. Part Names

4.1 Front view

Lens Connector for Auto-iris lens (DC Drive)

1 Back Focus Adjustment 2Dust Protection Cap

3Lens connector for auto iris lenses 4Back focus Adjustment Lock Screw

5Camera Mount Hole (Top and Bottom)

PIN No

DC Iris

Damp(-)

Damp(+)

Drive(+)

GND

PIN 4 PIN 2

PIN 3 PIN 1

VTC-C770DN

ⓐ

ⓑ

ⓒ

ⓓ

4.2 Rear side view

5. Installation and Commissioning Instructions

•Make sure the power is removed before the installation.

•To apply power:

First connect the low voltage (DC12V or AC24V). Then plug the AC adapter to AC outlets to avoid an

improper reset from power jitter and a damage from the surge voltage when no load.

5.1. Attaching the lens

•Remove the Dust Protection cap from the lens mount

•Screw the lens onto the camera without using force

5.2. Setting the back focus lock

The back focus is the distance between the lens support on the camera and the image sensor. Optimum

focus is only possible when the correct distance is set. It may be necessary to set the back focus in

individual cases due to production tolerances of the lens. The iris of the lens must be open as wide as

possible. (Smallest F value) to set the back focus. For lenses with automatic iris control, you will require an

ND filter (gray filter) to prevent the iris from closing in bright light.

Setting for lenses with a fixed focal distance

If the focus cannot be set exactly by turning the focus ring (lens), please proceed as follows:

ⓐOSD menu switches (Up/ Down/ Left/ Right / Enter)

ⓑVideo Output Connector (BNC)

ⓒPower indicator LED

ⓓPower Input Terminal

VTC-C770DN

1. Point the camera at an object with sufficient contrast. The distance to the object should be longer than

1,000 x the focal distance.

2. Open the iris on the lens

3. Set the focus of lens so that the distance at the lens is close to infinity but not to exact infinity position.

4. Loosen Back focus Adjustment Lock: Screw one~two turns on the camera with industrial “+” driver

5. Rotate Back Focus Adjustment until the optimum focus is achieved.

6. Tighten Back focus Adjustment Lock Screw again.

7. Trim the focus precisely at lens if necessary.

Setting for lenses with a variable focal distance (zoom):

If the focus changes as the focal distance changes, please proceed as follows:

1. Point the camera at an object with sufficient contrast at a distance of approximately 2 meters

2. Open the iris on the lens

3. Set the maximum focal distance (Tele) at the lens

4. Set the optimum focus with the focus ring

5. Set the smallest focal distance (wide angle)

6. Loosen Back focus Adjustment Lock. Screw one~two turns on the camera with the industrial “+” driver

7. Adjust Back Focus Adjustment until the optimum focus is achieved. Steps 3,4,5 and 7 may need to be

repeated several times to obtain the best results

8. Tighten Back focus Adjustment Lock Screw again

5.3. Installation

The camera has a 1/4”thread insert on its top and bottom sides for mounting the camera to a tripod, wall

or ceiling with a corresponding mount.

5.4 Commissioning

• First, connect the power supply to the power terminal on the rear panel of camera

• Second, plug the power adaptor to the main supply

• ⓒPower indicator LED will be lit

• The camera is ready for operation

5.5. Power Supply Connections

Camera can work with either 24VAC or 12VDC, dual voltage power. It does NOT require the polarity-

matched connection for 12VDC supply. Primary and secondary grounds are completely isolated to avoid

the possible ground-loop problems. Its excellently wide operating voltage range of 10.5V-30V for DC and

12-28.8V for AC gives extra flexibility at the installation.

VTC-C770DN

6. SETUP menu

6.1 In the menu

Use , buttons to move the cursor and , buttons to change the settings.

Press button to select or enter. button stands for MENU or ENTER button.

6.2 MAIN menu

Follow the chart for submenu settings

MAIN menu-1

Default

Descriptions

SHUTTER

/AGC

AUTO

Sets the parameters related to the shutter mode and AGC for AUTO and

MANUAL settings. See '6.3 SHUTTER/AGC menu' for details.

LENS

AUTO

Selects the lens type, AUTO or MANUAL. AUTO supports DC auto-iris lens

only. See '6.4 LENS menu' for details.

DAY/NIGHT

AUTO

Sets DAY/NIGHT mode to AUTO, COLOR or B/W.

AUTO –Camera switches DAY from/to NIGHT automatically.

BURST, DELAY CNT, DAY→NIGHT, NIGHT→DAY can be set.

See '6.5 DAY/NIGHT menu' for details.

COLOR –Day/Night is disabled and forces to DAY mode only.

B/W –Day/Night is disabled and forces to NIGHT mode only.

Camera removes IR cut filter and switches to B/W.

PICTADJUST

Sets MIRROR, BRIGHTNESS, CONTRAST, SHARPNESS, HUE or GAIN.

See '6.6 PICT ADJUST menu' for details.

WHITE BAL

ATW

Sets ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK.

See '6.7 WHITE BAL menu' for details.

ATR

OFF

Sets ON/OFF for enabling/disabling ATR (Adaptive Tone Reproduction)

compensation for the better dynamic range of the image.

See '6.8 ATR menu' for adjusting the dynamic ranges.

BACKLIGHT

OFF

Selects BACKLIGHT mode out of OFF, HLC or BLC. Areas and gains for

HLC and BLC are factory preset and not user adjustable.

Moves to MAIN menu-2.

EXIT

Exits the setup menu. To save the changes, move cursor to 'SAVE ALL'

and press button before exiting the setup menu.

SAVE ALL

Saves all parameters by pressing button.

MAIN menu-1

MAIN menu-2

6.2.1 MAIN menu-1

VTC-C770DN

6.2.1 MAIN menu-2

6.3 SHUTTER/AGC menu

This menu offers how to control/select SHUTTER,AUTO IRIS and AGC to get the best image for the high

luminance and the low luminance according to the scene.

For example, to reduce the wash out and extend the dynamic range for the highlight scene, it is improved

by SHUTTER+AUTO IRIS in the outdoor daylight. This mode may show color rolling or the video level

hunting problem in certain lighting condition such as fluorescent lights.

Flickerless mode reduces the flickers by NTSC camera under 50Hz light or PAL camera under

60Hz light. MAIN> SHUTTER/AGC> MANUAL> SHUTTER must be set to 1/100 (NTSC), 1/120 (PAL) and

MAIN> SHUTTER/AGC> AUTO> MODE to AUTO IRIS. Normal shutter speed with an auto iris lens

should be set to 1/60 (NTSC) and 1/50 (PAL) for the best sensitivity.

To enter SHUTTER/AGC menu, press button at MAIN menu-1>SHUTTER/AGC.

MAIN menu-2

Default

Descriptions

Sets the noise reduction parameters for NR MODE, Y LEVEL and

C LEVEL. See '6.9 NR menu' for details.

MOTION DET

OFF

Sets ON/OFF for enabling/disabling MOTION DET.

See '6.10 MOTION DET menu' for the parameter settings.

PRIVACY

OFF

Sets ON/OFF for enabling/disabling PRIVACY.

See '6.11 PRIVACY menu' for the parameter settings.

LANGUAGE

ENGLISH

Selects the language out of 7 languages.

CAMERA ID

OFF

Sets ON/OFF for enabling/disabling of ID display.

Factory default ID is this version of the camera.

User programmed camera ID will be lost and restored with Factory default

ID after CAMERA RESET. See '6.12 ID menu' for editing ID.

CAMERA

RESET

Restores FACTORY DEFAULT.

To save the restored parameters, move cursor to 'SAVE ALL' and press

button before exiting the setup menu.

BACK

Returns to MAIN menu-1.

EXIT

Exits the setup menu.

To save the changes, move cursor to 'SAVE ALL' and press button.

SAVE ALL

Saves all settings by pressing button.

Andere Handbücher für VTC-C770DN

Inhaltsverzeichnis

Andere Vitek Sicherheitskamera Handbücher

Vitek

Vitek VTD-MD5CH Bedienungsanleitung

Vitek

Vitek VT-PIRC1 Bedienungsanleitung

Vitek

Vitek Transcendent Series Bedienungsanleitung

Vitek

Vitek Transcendent VTC-TNT8RFEA-2 Bedienungsanleitung

Vitek

Vitek VTC-IRLED30A Bedienungsanleitung

Vitek

Vitek VTC-LED307BB Bedienungsanleitung

Vitek

Vitek VTC-EB15B Bedienungsanleitung

Vitek

Vitek VTC-IRX36/3895 Bedienungsanleitung

Vitek

Vitek VTD-C75 Bedienungsanleitung

Vitek

Vitek INDOOR MIGHTY DOME - Bedienungsanleitung

Vitek

Vitek Transcendent VTC-TNB4RFA3 Bedienungsanleitung

Vitek

Vitek VTC-THB5R3 Bedienungsanleitung

Vitek

Vitek TRANSCENDENT VT-TPTZ4AD-4M Bedienungsanleitung

Vitek

Vitek VTC-C770WS Bedienungsanleitung

Vitek

Vitek VT-PTZ220NP Bedienungsanleitung

Vitek

Vitek VTC-IRV30/2810 Bedienungsanleitung

Vitek

Vitek Transcendent Series Bedienungsanleitung

Vitek

Vitek VTD-VH49VP4 Bedienungsanleitung

Vitek

Vitek VTC-C2NZ Bedienungsanleitung

Vitek

Vitek Transcendent VTC-TNB8MADW Bedienungsanleitung

Vitek

Vitek VTC-HD713A Bedienungsanleitung

Vitek

Vitek VTC-TTT28R2F Bedienungsanleitung

Vitek

Vitek Transcendent VTC-THB2RFS Bedienungsanleitung

Vitek

Vitek VTC-B74 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung