Vitek VTC-IRA40/3516 Bedienungsanleitung

VITEK

VTC-IRA40/3516

750 TV Line Day/Night

IR Bullet Camera

w/150’ Range (960H)

• 1/3” High density Sony® CCD (960H)

• High Resolution of 750 Horizontal Lines

• Sony Effio-A Digital Signal Processor

• Simple Installation with External Focus and Zoom control and one

turn mount positioning lock

• True Day/Night by ICR (Infrared Cut Removal)

• E-WDR by ATR-EX (Adaptive Tone Reproduction)

• 40 Infrared LEDs at 850nm enable viewing in total darkness up to

150 feet

• 0.003 Lux (Sens-up Off) / 0 Lux (IR-ON)

• 3.5-16mm Varifocal Auto Iris Lens with External Adjustments for

Focus and Zoom

• True Day/Night by ICR - Infrared Cut Removal

• XD-DNR (2D+3D DNR) Advanced Digital Noise Reduction

• Built-in Motion Detection with a 24x16 Grid

• OSD (On Screen Display) menu and Camera ID

• Dual Glass Compartments to Eliminate Glare

• IP68 NEMA Rating

• Heavy Duty Mount with Cable Feed Through

• Secondary Video Output & OSD Control Joystick are accessible

inside a gasket sealed removable side panel

• 24VAC/12VDC Dual Voltage

Safety Precaution

ULTRA CLEAR RESOLUTION CAMERA

CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To prevent electric shocks and risk of fire hazards, do NOT use other than

specific power source.

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

Caution :

Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority

to operate the equipment.

Mains power quality should be that of a typical commercial environment. If the user

of the model requires continued operation during power mains interruptions, it is

recommended that the model be powered from an uninterruptible power supply

(UPS) or a battery.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

ULTRA CLEAR RESOLUTION CAMERA

Safety Precaution

NOTICE

The image used in this instruction manual are processed to help comprehension

and may differ from actual video of the camera.

Avoid installing areas where has shock or vibration which results in the problems.

Pay attention to safety when laying the connection cable and observe that the

cable is not subjected to heavy loads, kinks or damage and no moisture can get

in.

Never open the device such as boards or lens.

The warranty becomes void if repairs are undertaken by unauthorized persons.

Maintenance and repair have to be carried out only by authorized service centers.

Use only a mild detergent to clean the housing.

The camera should never be operated beyond the technical specifications.

This can lead to destruction.

The camera should never be operated in water.

ULTRA CLEAR RESOLUTION CAMERA

Contents

Safety Precaution

p.02~03

Contents

p.04

Features

p.05

Composition

p.05

Dimensions

p.06

Part Names

p.07

Installation Instructions

p.08~10

Operating Instructions

p.11~30

Specifications

p.31

ULTRA CLEAR RESOLUTION CAMERA

Features

Key Features

General Description

• With ICR mechanism,

- Enhances its sensitivity about 10x at night time

- Can accepts the infrared light

This is an ultra-clear resolution camera which realizes over 750TVL resolution

and a crisp color reproduction with SONY 960H CCD and Effio-A Enhanced

image signal processor.

• 1/3” High density Sony CCD (960H)

• 750TVL High-Resolution

• D-WDR by ATR-EX

• TDN with Dual Filter Switcher

• 3.5~16mm F1.2 DC Auto Iris Vari-focal Lens

• XD-DNR (2D+3D DNR) Advanced Digital Noise Reduction

• Improved IR-Optimizer

• DIS(Digital Image Stabilizer)

• Scene Preset, LSC (Lens shading compensation), Motion detection,

E-Zoom, Polygon privacy mask(up to 15), Defog, Sens-up, BLC/HLC

• External Zoom & Focus adjustment

• IR-LED 40pcs

• Up the Coaxial (UTC) communication

• OSD Menu & Video Sub-out port for easy installation & maintenance

• Circuit protection against faulty connection in power polarity

• Isolated power supply against ground loop problem

• Dual Window, One-touch 3-Axis locking bracket, Easy installation pad

• IP68 Protection

• With Effio-A series Enhanced digital imaging system,

- Delivers the crystal clear images providing 750TVL resolution in conjunction

with SONY 960H High density CCD.

- They are provided ‘D-WDR by ATR-EX’ function

- Color signal processing provides the optimum balance between the luminance

and chroma signals for high color reproducibility even for the detail scene which

contains very high spatial frequency.

- Incorporates 2D+3DNR signal processing.

ULTRA CLEAR RESOLUTION CAMERA

Composition

Dimensions

Torque Wrench:

3mm (1pc)

Video Sub-out:

Cable (1pc)

Mounting Screw:

4 x 30mm (4pcs)

Plastic Anchor:

6 x 30mm (4pcs)

Operating

Instruction

Camera

4.35” (110.5mm)

3.53” (89.6mm)

4.37” (111mm)

3.94” (100mm)

3.31” (84mm)

3.39” (86mm)

3.15” (80mm)

10.11” (256.70mm)

Cable Signal

Sticker

Wiring Connector:

(1pc)

Easy

Bracket

Assembly Screw:

4 x 14mm (4pcs)

Mounting Template

ULTRA CLEAR RESOLUTION CAMERA

Part Names

DUAL WINDOW

SUNSHIELD BOLT

SUNSHIELD

FRONT CASE

OSD Setup

CONTROL COVER

BRACKET

EASY

BRACKET

REAR CASE

CAUTION

• Extreme care should be taken NOT to scratch the window in front of lens.

• Care should be taken the cable is NOT damaged, kinked or exposed in

hazardous area.

• Do not expose the camera lens directly to a strong light source such as the sun or

spot light.

POWER CABLE

ULTRA CLEAR RESOLUTION CAMERA

Installation Instructions

Mounting Screw

: 4x30mm

Plastic Anchor

: 6x30mm

Torque Wrench

1. Place the mounting template at the installation position and drill the ceiling or

wall if needed. ( *The easy bracket can not be installed on the ceiling)

2. Place the easy bracket on pre-drilled position and attach using the mounting

screws(4x30mm). Skip this step when an easy bracket is not installed.

3. Route the power cable to the connecting place.

Hook up the camera bracket with the easy bracket as illustrated below.

4. Attach the camera bracket through using assembly screws (4x14mm).

5. Set the camera’s viewing angle.

6. Place the sunshield onto the camera unit and tighten the sunshield-bolts.

REAR VIEW

Cable exit

Assembly Screw

: 4x14mm

ULTRA CLEAR RESOLUTION CAMERA

Installation Instructions

Pan & Tilt adjustments

1) Pan limit:

Pan is limited to +/- 90°.

3) Inclination limit

(Horizontal image alignment):

Inclination limited to +/-90° max.

2) Tilt limit:

Tilt is limited to 0°(2°) min ~ 90° max.

for wall(ceiling) installation respectively

with reference to the wall(ceiling) when

the inclination of camera module is 0°,

that is, the image is aligned horizontally.

• Unlock the screw on the camera bracket through using the torque wrench supplied

• Set the camera’s viewing angle then lock the screw on the bracket.

90° 90°

80°

90°

±90°

•on the wall

•on the ceiling

■Adjustment of viewing angle

with one-touch 3-Axis bracket

Torque

wrench

Lock/Unlock

Screw

ULTRA CLEAR RESOLUTION CAMERA

Installation and commissioning Instructions

• Make sure the power is removed before the installation.

• Follow the order for applying power.

First, connect the low voltage (AC24V or DC12V), then plug the AC adapter into

AC outlet to avoid an improper reset from power jitter and damage from the

surge voltage when no load.

Power Supply Connections

Camera can work with either 24VAC or 12VDC, dual voltage power.

Primary and secondary grounds are completely isolated to avoid possible

ground-loop problems

Installation Instructions

Zoom & Focus adjustments

• Turn the Focus gear to “N”(Near) or “∞”(Far)

until the sharpest focus is made.

• To widen the viewing angle, turn the Zoom to

“W”(Wide) and to obtain a closer view, turn it

to “T”(Tele)

Use the torque wrench supplied.

VIDEO (BNC)

AC24V/GND

AC24V/DC12V

N/A

※ Attach the Signal Assignment Sticker

in a visible spot for wiring reference.

Inhaltsverzeichnis

Andere Vitek Sicherheitskamera Handbücher

Vitek

Vitek VT-PIRC2 Bedienungsanleitung

Vitek

Vitek VTD-IR2811DN Bedienungsanleitung

Vitek

Vitek VT-PTZ40WH Bedienungsanleitung

Vitek

Vitek VT-TPTZ10HR-2A4 Bedienungsanleitung

Vitek

Vitek VTD-VS48B2 Bedienungsanleitung

Vitek

Vitek TRANSCENDENT VTC-TNB48R4M2 Bedienungsanleitung

Vitek

Vitek VTC-LED667CB Bedienungsanleitung

Vitek

Vitek VTC-IRLED24H Bedienungsanleitung

Vitek

Vitek VTC-B301 Bedienungsanleitung

Vitek

Vitek VTD-HOC4F Bedienungsanleitung

Vitek

Vitek VTD-IR90HD Bedienungsanleitung

Vitek

Vitek VTC-TNT8RMA4 Bedienungsanleitung

Vitek

Vitek Transcendent VTC-TNT8FADW-2 Bedienungsanleitung

Vitek

Vitek VTC-IRHCM1 Bedienungsanleitung

Vitek

Vitek VT-PIRC1 Bedienungsanleitung

Vitek

Vitek VTD-A4F/IW Bedienungsanleitung

Vitek

Vitek Transcendent VTD-TND6FPN Bedienungsanleitung

Vitek

Vitek VTC-IR1600/550 Bedienungsanleitung

Vitek

Vitek Transcendent Series Bedienungsanleitung

Vitek

Vitek VT-TPTZ10HR-5N Bedienungsanleitung

Vitek

Vitek VTC-TNB36R3V2 Bedienungsanleitung

Vitek

Vitek VTC-T4T3HR2MD Bedienungsanleitung

Vitek

Vitek Mighty VTD-MP2810WDR Bedienungsanleitung

Vitek

Vitek Transcendent Series Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung