Vitek VTC-IRE40 Bedienungsanleitung

blackyellowmagentacyan

28492 Constellation Road ValenCia, Ca 91355

WWW.ViteKCCtV.CoM | 888-ViteK-70

VITEK

VTC-IRE40/3516

Day/Night Infrared 700 TV Line

Bullet Camera w/150’ Range

• 700TVL High Resolution

• High Density 1/3” Sony EXVIEW CCD & Effio-E DSP

• 40 Infrared LEDs at 840nm enable viewing in total darkness up

to 150 feet

• 0.003 Lux (F1.2 @ 40IRE) / 0 Lux with IR LEDs On

• E-WDR by Adaptive Tone Reproduction

• 3.5-16mm Varifocal Auto Iris Lens with External Adjustments for

Focus and Zoom

• 2DNR Noise Reduction

• True Day/Night by ICR - Infrared Cut Removal

• Motion Detection

• Weatherproof IP68 NEMA Rating

• Privacy & Highlight Masking

• OSD (On Screen Display) and Secondary Video Output

• 24VAC/12VDC Dual Voltage

1. Safety Instructions and Notes….......................................................................................................

2. General Descriptions............................................................................……………………………...

3. Supplied Items......................................................................................……………………………...

4. Part names…………………………….…...................................................…………………………...

5. Installation Instructions......................................................................................……………………...

6. Setup Menu ……………............................................................................…………………………...

7. Specifications ……………………………………………….....................................................................

8. Dimensional Drawings ……………………………………………............................................................



To prevent fire or shock hazard, do not expose the unit to rain or moisture.

This symbol is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature

accompanying the unit.

This symbol is intended to alert the user to the presence of

uninsulated "dangerous voltage" within the product's enclosure that

may be of sufficient magnitude to constitute a risk of electric shock.

Warning (NTSC version) -- This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation

of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at their own expense.

Caution -- Any changes or modifications in construction of this device that are not approved by the party

responsible for compliance could void the user's authority to operate the equipment.

Notice -- The images used in this manual are processed to help comprehension and

may differ from the actual video of the camera.

1. Safety Instructions and Notes

• Please read these safety and operating instructions before placing the camera into operation.

• Keep the manual in a safe place for later reference.

• Pay attention to safety when laying the connection cable and observe that the cable is not subjected to

heavy loads, kinks, damage or moisture.

• Never open the device to expose boards or lenses.

The warranty becomes void if repairs are undertaken by unauthorized persons.

• Only authorized service centers may perform maintenance or repairs.

WARNING

Caution

To prevent electric shocks

and risk of fire hazards, do

NOT use other than specified

power source.

• Use only a mild detergent to clean the housing.

• Keep the window surface clean of dirt or dust, which may reflect infrared light into the lens at night.

• The camera should never be operated beyond the technical specifications. This can lead to destruction.

2. General Descriptions

This camera is an ultra clear resolution camera that realizes over 700TVL resolution and a crisp color

reproduction with Sony 960H EX-view CCD and Effio-E image signal processor.

Effio-E digital imaging system:

• Delivers crystal clear images with over 700TVL resolution that accurately captures every aspect of any

scene

• Color signal processing provides optimum balance between luminance and chroma signals for

high color reproducibility, even for a detailed scene containing very high spatial frequency

• Incorporates 2-D noise reduction signal processing

ICR mechanism:

• Enhances sensitivity up to 10x at night.

• Accepts infrared light

24VAC/12VDC dual power design:

• Offers flexibility of installation

• Ensures reliability

Main features:

•External adjustment controls for lens and On Screen Display (OSD)

•High Density 1/3" Sony EX-view CCD (960H)

•Resolution 700 Horizontal Lines

•3.5-16mm Variable Focal Length Lens

•Weatherproof IP68 NEMA Rating Optimized for Outdoor Use

•Secondary Video Output for simple installation & Maintenance

•40ea Self Adjusting “Dynamic Intensity” IR LEDs

•150’ Night Observation Range

•E-WDR by ATR (Adaptive Tone Reproduction)

•2-D noise reduction

•True Day/Night with Automatically Removable IR Cut Filter (ICR)

•Motion Detection

•Privacy Mask Function

•OSD menu and camera ID

•Switches to B/W enabling infrared spectrum response in night mode

•Very low noise and superior picture quality

•Sensitivity of 0.003Lux (F1.2@40IRE)

•Automatic White Balance (ATW)

•Supply voltage: 24Vac/12Vdc Dual voltage

3. Supplied Items

• 1x VTC-IRE40/3516 Long range Weatherproof IR Bullet camera

• 1x Installation and Operating Instructions

• 1x Mounting template

• 1x ⓖ!Sunshield with Attachment thumb screw for Sunshield panel

• 1x ①3mm Hex L-wrench

• 4x ②anchors

• 4x ③Wall mounting screws

• 1x ④Video Sub-output cable

4. Part Names

4.1 Front view

3. Supplied Items

Sunshield attachment thumb screw

IR LED Panel

Double Glass Window

ⓔ

ⓕ

ⓒ

ⓓ

ⓐ

ⓑ

ⓖ

ⓗ

Mounting Bracket Foot

ⓔFoot mount Hole(x4)

ⓕArm assembly

ⓖSunshield

ⓗOSD (On Screen Display

Control) cover

①

②

③

④

4.2 Rear side view

5. Installation Instructions

•Make sure the power is not applied before the installation.

•Once the camera is installed, you may first connect the low voltage (AC24V or DC12V) wire to the

camera power connector, then plug the AC adapter to the AC outlets to avoid an improper reset from

power jitter and possible damage from voltage surge.

5.1. Mounting the camera

1) Drill 4 holes into the wall or ceiling using the supplied template

2) Insert the ②anchors into the drilled holes

3) Match ⓔ( foot mount holes) to the drilled holes

4) Affix the mounting bracket by using ③supplied screws

ⓛFocus adjustment

ⓚZoom adjustment

ⓛ

ⓚ

Installation on Wall

Installation on Ceiling

5.2. Power Supply Connections

The VTC-IRE40/3516 can operate on either 24AC or 12VDC, dual voltage power.

It is required that the polarity-matched connection is made for 12VDC supply, otherwise IR LEDs,

will not operate at night.

Primary and secondary grounds are completely isolated to avoid possible ground-loop problems.

5.3. Limit of pan and tilt

1. Pan limit

Pan is limited to +/- 90°.

2. Tilt limit

Tilt is limited to 0° (2°) min ~ 90° max.

Clamp connectors of power input

AC24V/DC12V (RED WIRE)

AC24V/GND (BLACK WIRE)

Installation on Wall

Installation on Ceiling

3. Inclination limit (horizontal image alignment)

Inclination limited to +/-90° max.

6. SETUP Menu

6.1 In the menu

The Setup menu can be accessed and controlled by the OSD control joy stick on the side of the camera.

Five commands are available with the joy stick.

In the menu, use ▲,▼to move menu, ◀,▶to change the settings and press ●to select or enter.

The FACTORY DEFAULT in this manual may NOT be the same as the default values set

by the

FACTORY due to feature improvements or customer requirements.

To enter the menu, press ●.

6.2 MAIN menu

Follow the chart below for submenu settings.

Joy stick

VIDEO

SUB-OUT

connector

SYMBOL descriptions for joystick operation;

1. ▲,▼,◀,▶- Denotes the direction

of Joystick lever operation.

2. ●- Denotes “ENTER” by pressing

down on the Joystick lever

MAIN Menu-1

MAIN Menu-2

MAIN menu-1

Default

Descriptions

SHUTTER

/AGC

AUTO

Sets the parameters related to the shutter mode and AGC for AUTO and

MANUAL settings. See '6.3 SHUTTER/AGC menu' for details.

LENS

AUTO

Selects the lens type, AUTO or MANUAL. AUTO supports DC auto-iris lens

only. See '6.4 LENS menu' for details.

DAY/NIGHT

AUTO

DAY/NIGHT mode for AUTO only with IR LED version.

AUTO – Camera switches DAY from/to NIGHT automatically by the built-in

light sensor.

BURST, DELAY CNT, DAY→NIGHT, NIGHT→DAY can be set.

See '6.5 DAY/NIGHT menu' for details.

PICT ADJUST

Sets MIRROR, BRIGHTNESS, CONTRAST, SHARPNESS, HUE or GAIN.

See '6.6 PICT ADJUST menu' for details.

WHITE BAL

ATW

Sets ATW, PUSH, USER1, USER2, ANTI CR, MANUAL or PUSH LOCK.

See '6.7 WHITE BAL menu' for details.

ATR

OFF

Sets ON/OFF for enabling/disabling ATR (Adaptive Tone Reproduction)

compensation for the better dynamic range (E-WDR) of the image.

See '6.8 ATR menu' to adjust the dynamic ranges.

BACKLIGHT

OFF

Selects BACKLIGHT mode out of OFF, HLC or BLC. Areas and gains for

HLC and BLC are factory preset and not user adjustable.

Moves to MAIN menu-2.

EXIT

Exits the setup menu. To save the changes, move cursor to 'SAVE ALL'

and press ●button before exiting the setup menu

SAVE ALL

Saves all parameters by pressing ●button when cursor is on 'SAVE ALL'

6.2.1 MAIN menu-1

6.2.1 MAIN menu-2

6.3 SHUTTER/AGC menu

This menu shows how to control/select SHUTTER, AUTO IRIS and AGC to get the optimum image for

high luminance and the low luminance according to the scene.

For example, to reduce the “wash out” and extend the dynamic range for a highlighted scene, you will use

SHUTTER+AUTO IRIS in outdoor daylight. This mode may show color rolling or video level hunting

problems in a certain lighting condition such as fluorescent lights.

For Flickerless mode which reduces flicker by NTSC cameras under 50Hz light or PAL camera under

60Hz light, MAIN>SHUTTER/AGC>MANUAL>SHUTTER must be set to 1/100(NTSC), 1/120(PAL) and

MAIN>SHUTTER/AGC>AUTO>MODE to AUTO IRIS. Normal shutter speed with an auto iris lens should

be set to 1/60(NTSC) and 1/50(PAL) for the optimum sensitivity.

This is a complicated menu so please proceed with care when handling the Shutter.

To enter SHUTTER/AGC menu, press ●button at MAIN menu-1>SHUTTER/AGC.

MAIN menu-2

Default

Descriptions

Sets the noise reduction parameters for NR MODE and Y LEVEL,

C LEVEL. See '6.10 NR menu' for details.

MOTION DET

OFF

Sets ON/OFF for enabling/disabling MOTION DET.

See '6.11 MOTION DET menu' for the parameter settings.

PRIVACY

OFF

Sets ON/OFF for enabling/disabling PRIVACY.

See '6.12 PRIVACY menu' for the parameter settings.

LANGUAGE

ENGLISH

Selects the language out of 7 languages.

CAMERA ID

OFF

Sets ON/OFF for enabling/disabling of ID display.

Factory default ID is Software version of camera.

User programmed camera ID will be lost and restored with Factory default

ID by CAMERA RESET. See '6.13 ID menu' for editing ID.

CAMERA

RESET

Restores FACTORY DEFAULT.

To save the restored parameters, move cursor to 'SAVE ALL' and press

●button before exiting the setup menu.

BACK

Returns to MAIN menu-1.

EXIT

Exits the setup menu.

To save the changes, move cursor to 'SAVE ALL' and press ●button

before exiting the setup menu

SAVE ALL

Saves all settings by pressing ●button when cursor is on 'SAVEALL'

Andere Handbücher für VTC-IRE40

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vitek Sicherheitskamera Handbücher

Vitek

Vitek VT-PIRC2H Bedienungsanleitung

Vitek

Vitek Transcendent VTD-TND4RFA3/-2 Bedienungsanleitung

Vitek

Vitek VT-PTZ10 Bedienungsanleitung

Vitek

Vitek VTD-VPH266 Bedienungsanleitung

Vitek

Vitek VTD-C510 Bedienungsanleitung

Vitek

Vitek VT-SMKC1 - DATASHEET 2 Bedienungsanleitung

Vitek

Vitek VTD-TND4RFA4 Bedienungsanleitung

Vitek

Vitek Transcendent 5 Series Bedienungsanleitung

Vitek

Vitek Transcendent VTD-TNMD4RFA4-2 Bedienungsanleitung

Vitek

Vitek VTC-TNT5RFE-2 Bedienungsanleitung

Vitek

Vitek VTD-MH2910 Bedienungsanleitung

Vitek

Vitek VTC-IRT40-2812 Bedienungsanleitung

Vitek

Vitek Transcendent Series Bedienungsanleitung

Vitek

Vitek Mighty Series Bedienungsanleitung

Vitek

Vitek VTC-TNB4RMA4B Bedienungsanleitung

Vitek

Vitek Alpha VTC-IRLED24 Bedienungsanleitung

Vitek

Vitek VTD-MD2-4 Bedienungsanleitung

Vitek

Vitek VT-PIRC2H Bedienungsanleitung

Vitek

Vitek VTC-C661 Bedienungsanleitung

Vitek

Vitek VTC-EBV49/24 Bedienungsanleitung

Vitek

Vitek VTC-C680 Bedienungsanleitung

Vitek

Vitek TRANSCENDENT VTD-TND3RVEB Bedienungsanleitung

Vitek

Vitek VTD-MD5CH Bedienungsanleitung

Vitek

Vitek VTD-IR2811DN Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung