Vitek VTC-THB5R3 Bedienungsanleitung
VITEK
VTC-THT5R3/R2
VTD-THD5R3/R2
VTC-THB5R3/R2
Transcendent 5.0 Megapixel Indoor/Outdoor
HD-TVI/AHD/CVI/CVBS Fixed Lens IR Cameras
FEATURES
• 1/2.7” 5.0 MegaPixel Progressive Scan CMOS Image Sensor
• High Definition Analog (HDA): HD-TVI / AHD: 5.0MP /
HD-CVI: 4.0MP / CVBS: 960H Video Output
• 3.6 or 2.8mm Fixed Iris Lens Options
• Supports OSD Menu
• 2 Matrix IRs with up to 165’ IR Range (VTC-THB5R3/R2)
• 1 Matrix IR with up to 100’ IR Range (VTC-THT5R3/R2)
• 16 IR LEDs with up to 65’ IR Range (VTD-THD5R3/R3)
• True Mechanical Day/Night function by ICR
• Digital Wide Dynamic Range (D-WDR)
• XD-DNR Noise Reduction
• IP67 Weather Resistance (+IK10 on VTD-THD5R3/R2)
• Supports Control over COAX (CoC)
• Over 1500’ HD Video Transmission (Depending on cable
characteristics and integrity)
• VTC-THB5R3/R2: J Boxes - VT-TJB07, TJB08
VTC-THT5R3/R2: J Boxes - VT-TJB01, TJB08, Wall Mount VT-TWMT-3
VTD-THD5R3/R2: J Box - VT-TJB03A, Wall Mount VT-TWMT-3,
In-ceiling Semi Flush Mount VT-TFMT-S
• 12VDC Operation
• 3-year Warranty
2
Safety Precautions
CAUTION: TO REDUCE THE RISK OF ELECTICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
To prevent electrical shock and risk of fire hazards, do not expose this unit
to rain or moisture and only use specified power source..
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of atypical commercial environment. If the user
of the model requires continued operation during power interruptions, it is
recommended that the device be powered from an uninterruptible power supply
(UPS).
The symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user tothe presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude toconstitute a risk of electrical shock.
3
VTC-THB5R3/R2 - Components
Overview
34
57
6
Lens
Sun Shield
Mount Lock
Mount Base
BNC Video Output
Output Mode Switch
Power Cable
1
2
3
4
5
6
7
2
1
Video Connection
Connect the BNC video connector to a BNC cable, then to a DVR.
Power
12VDC
Power Connection
Connect the power connector to a regulated 12 VDC power adaptor.
Monitor
Video
This series supports AHD/TVI/CVI/CVBS video output.
The video output can be changed by pressing and holding the button in the
video switch cable for 5 seconds (the default video output is TVI video
output). Before switching video outputs, please remove the cover of the
video switch cable.
Video Output Mode Switch:
Camera
Manual
Drill Template
Screws
Hex Wrench
Installation
Before beginning installation, make
sure that the wall or ceiling is strong
enough to withstand 3 times the weight
of the camera. The mounting steps are:
2. Route the cables and connect the power & video cables, use the
rubber plug to fill the gap of the mounting base, then secure the
mounting base to the ceiling or wall with screws.
Rubber plug
3. Loosen the mount lock to adjust the pan and tilt, then tighten the
mount lock to secure the viewing angle adjustments.
4. Carefully remove the protective film from the lens to complete the
installation.
90° T ILT
360° ROTATION
360° PAN
FIXED RING
1. Attach the drill template to
the place where you want to
install the camera, then drill
3 screw holes and 1 cable
hole (if routing the cables
through the mounting base)
according to the drill
template
4
5
VTC-THT5R3/R2 Components
Overview
2
1
3
4
Camera
Manual
Screws
Hex Wrench
Mounting Plate
Rubber Plug
Lens
Lock Screws
BNC Video Output
Output Mode Switch
Power Cable
1
2
3
4
5
5
Monitor
Video
Video Connection
Connect the BNC video connector to a BNC cable, then to a DVR.
Power Connection
Connect the power connector to a regulated 12 VDC power adaptor.
Power
12VDC
This series supports AHD/TVI/CVI/CVBS video output.
The video output can be changed by pressing and holding the button in the
video switch cable for 5 seconds (the default video output is TVI video
output). Before switching video outputs, please remove the cover of the
video switch cable.
Video Output Mode Switch:
6
Installation
Before you begin, please make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting
steps are as follows:
1. Attach the drill template to
the place where you want to
install the camera, then drill
3 screw holes and 1 cable
hole (if you want to route the
cables through the mounting
base) according to the drill
template
.
2. Route the cables and
connect the power & video
cables, then secure the
mounting base to the ceiling
or wall with screws.
3. Loosen the lock screws, then
adjust the camera to obtain
the optimium viewing angle.
Confirm the correct viewing
angle with a monitor. Next
insert the rubber plug.
4. Tighten the lock screws to secure the viewing angle adjustments.
Rubber Plug
7
VTD-THD5R3/R2 Components
Overview
Camera
Manual
Drill Template
Screws
Hex Wrench
Mounting Base
Dome Cover
BNC Video Output
Output Mode Switch
Power Cable
1
2
3
4
5
1
2
3
4
5
Monitor
Video
Video Connection
Connect the BNC video connector to a BNC cable, then to a DVR.
Power Connection
Connect the power connector to a regulated 12 VDC power adaptor.
Power
12VDC
This series supports AHD/TVI/CVI/CVBS video output.
The video output can be changed by holding and pressing the button in the
video switch cable for 5 seconds (the default video output is AHD video
output). Before switching video outputs, please remove the cover of the
video switch cable.
Video Output Mode Switch:
88
4. Adjust the Three-axis camer bracket to obtain the optimium
viewing angle.
5. Install the dome bubble on
the camera with the screws,
then carefully remove the
protective film to complete
the installation.
Installation
Before beginning installation, make sure that the wall or ceiling is
strong enough to withstand 3 times the weight of the camera. The
mounting steps are as follows:
2. Loosen the screws to open
the lower dome and then
loosen the lock screw to
remove the mounting base.
1. Attach the drill template to
the place where you want to
install the camera, then drill
the screw holes and 1 cable
hole according to the drill
template.
3. Route the cables and
connect the power & video
cables, use the rubber plug
to fill the gap of the mounting
base. then secure the
mounting base to the ceiling
or wall with screws.
Rubber Plug
Pan: 0°~240°
Rotation: 0°~220° Tilt: 0°~68°
9
Camera OSD Menu
The Transcendent 4-in1 camera series must be connected to a DVR
which supports HD-TVI/AHD video signal input and COC protocol to
access the OSD setup menu. Different DVRs manufacturers may have
different modes of menu operation.
You can select the menu by clicking (U) or (D) key on the
direction area. Click (L) or (R) key to select the menu on the
left. The menu with arrow icon which means it has sub-menu. You
can select the menu and click the Enter Button to enter the
sub-menu. to return to previous screen, arrow down to Return and
click Enter Button. To Exit menu arrow down to Exit and click Enter
Button.
You will see the following interface by clicking the PTZ button.
The Following image will pop-up when you left click once on the
image when using Transcendent HDA DVR's.
Click on the OSD tab and then click on the camera menu
button.
10
Detailed Specifications VTC-THT5R3/R2 VTC-THB5R3/R2
Image Sensor
Signal System
Effective Pixels
Resolution
Video Output
Lens
Day/Night
Min. IIIumination
IR LEDs
IR Distance
S/N Ratio
WDR
Digital Noise Reduction (DNR)
White Balance
BLC
Up the COAX Control (COC)
Transmission Distance
Power Input
Power Consumption (12VDC)
Resistance Rating
Operation Conditions
Weight
Dimensions
1/2.7” 5.0 Megapixel Progressive Scan CMOS Sensor
PAL/NTSC
2592 x 1944
HD-TVI & AHD: 5.0 MegaPixel / CVI: 4.0 MegaPixel / CVBS: 960H
HD-TVI / AHD / CVI / CVBS (Selectable)
3.6 or 2.8mm - Fixed
True Day/Night by ICR
Up to 165’
≥52dB (AGC Off)
Digital DNR
Auto (AWB)
YES
YES
Up to 1500’ (Depending on cable characteristics & integrity)
12VDC
IP67
-4°~122° / 10%~90% Humidity
8.68 x 3.15” x 2.78” (220.5 x 80.1 x 70.5mm)
2 Matrix
Ф4.25 x 3.75” (Ф108 x 95.7mm)
Digital WDR
VTD-THD5R3/R2
Ф4.57 x 3.58” (116×91mm)
(+IK10)
Day : < 1W; Night : < 6W
20.11 oz. / 1.26 lbs. / 570g
14.81 oz. / .93 lbs. / 420g 23.23 oz. / 1.46 lbs. / 660g
16 IR LEDs
1 Matrix
Up to 65’
Up to 100’
Day : < 1W; Night : < 4WDay : < 1W; Night : < 4W
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Vitek Sicherheitskamera Handbücher
Vitek
Vitek Transcendent VTD-THMD2RF Bedienungsanleitung
Vitek
Vitek Virtuoso Series 8 Bedienungsanleitung
Vitek
Vitek Transcendent Series Bedienungsanleitung
Vitek
Vitek Transcendent VTC-TNT8RFEA-2 Bedienungsanleitung
Vitek
Vitek VTC-HOCRBD2812 Bedienungsanleitung
Vitek
Vitek VTC-TNT5RFEA-2 Bedienungsanleitung
Vitek
Vitek VT-TPTZ10HR-5N Bedienungsanleitung
Vitek
Vitek VTC-IRLED30HD Bedienungsanleitung
Vitek
Vitek VTD-MX2910-WDR Bedienungsanleitung
Vitek
Vitek VT-TPTZ10HR-2A4 Bedienungsanleitung
Vitek
Vitek Virtuoso Series 5 Bedienungsanleitung
Vitek
Vitek VTD-C75 Bedienungsanleitung
Vitek
Vitek VTD-TND5RFEA-2 Bedienungsanleitung
Vitek
Vitek VTC-C770DN Bedienungsanleitung
Vitek
Vitek TRANSCENDENT VTD-TND4RMA4 Bedienungsanleitung
Vitek
Vitek VTC-IRLED24H Bedienungsanleitung
Vitek
Vitek VTC-THT5R3 Bedienungsanleitung
Vitek
Vitek VTC-TTB42R2F Bedienungsanleitung
Vitek
Vitek VTC-IRLED30A Bedienungsanleitung
Vitek
Vitek Alpha Mega Series Bedienungsanleitung
