Vivo STAND-E-102B Bedienungsanleitung
Electric Height Adjustable Dual Monitor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-e-102b
SKU: STAND-E-102B
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
2
PACKAGE CONTENTS
22lbs
(10kg)per arm
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE MAY NOT BE USED
F (x1)
Single Arm
Bracket
G (x4)
Arm Cable Clips
H (x2)
VESA Plate
S-A (x4)
M6x12mm
Screw
S-B(x2)
Screw Cap
S-C (x2)
M3x8mm
Screw
M-A (x8)
M4x12mm
Screw
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TOOLS NEEDED
Phillips
Screwdriver
Pencil
SUPPORTED MONITOR RANGES :
Most 20” - 32” screens
Scissors
A (x1)
Electric Stand
B(x1)
Lower Clamp
Bracket
C(x1)
Upper Clamp
Bracket
D(x1)
Clamp Cable Clip
E(x1)
Dual Arm
I (x1)
Cable Sleeve
M-C (x8)
M5 Washer
T-A (x1)
4mm Allen
Wrench
M-B (x8)
M5x12mm
Screw
T-B (x1)
6mm Allen
Wrench
3
ASSEMBLY STEPS
STEP 1
Attach Upper Clamp Bracket (C) to the bottom of the Electric Stand (A) using M6x12mm
Screws (S-A) and a 4mm Allen Wrench (T-A).
STEP 2
For desktops between 10-55mm (0.40”-2.15”), align the key slots on Lower Clamp
Bracket (B) with the screws on Upper Clamp Bracket (C). Pull Lower Clamp Bracket (B)
down and lock the screws on Upper Clamp Bracket (C) in place with the 4mm Allen Wrench
(T-A).
For desktops between 50-85mm (2”-3.35”), remove the screws on Upper Clamp Bracket
(C) and reassemble them to the lower set of holes using 4mm Allen Wrench (T-A). Align the
key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C). Pull
Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place
with the 4mm Allen Wrench (T-A).
B
A
C
S-A
T-A
T-A
T-A
T-A
C
B
4
STEP 3
First, clamp the stand assembly onto desk. Press the Clamp Cable Clip (D) onto Upper
Clamp Bracket (C).
Option A: Dual Monitor Setup
STEP 4
Partially loosen screw on Dual Arm (E) with 6mm Allen Wrench (T-B) and slide Dual Arm (E)
onto the post of Electric Stand (A).
D
C
E
T-B
5
STEP 5
Re-tighten screw on Dual Arm (E) with arm assembly at the top of the post using the 6mm
Allen Wrench (T-B). Attach an Arm Cable Clip (G) onto each arm segment.
Note: The nal arm position will be determined in step 13.
STEP 6
Remove a single arm segment and the cable clip from Dual Arm (E) using the 6mm Allen
Wrench (T-B).
Single Arm
Segment
E
G
T-B
Cable Clip
Option B: Single Monitor Setup
T-B
T-B
6
STEP 8
Attach the single arm segment to Single Arm Bracket (F) using the 6mm Allen Wrench (T-B).
Note: This screw adjusts the joint tension. The tighter the screw the more resistance there
will be when pivoting the arm.
STEP 7
Loosely assemble the cable clip on Single Arm Bracket (F) using the 6mm Allen Wrench
(T-B).
Cable Clip
F
Single Arm Segment
Washer
Arm Screw
F
Clip Screw
T-B
T-B
7
STEP 10
Attach VESA Bracket (H) to monitors using either M4x12mm or M5x12mm bolts (M-A,M-B)
and Washers (M-C) along with a Phillips Screwdriver.
Monitor Installation
A
T-B
G
STEP 9
Re-tighten screw on Single Arm Bracket (F) with arm assembly at the top of the post using
the 6mm Allen Wrench (T-B). Attach an Arm Cable Clip (G) onto each arm segment.
Note: The nal arm position will be determined in Step 13.
F
H
8
STEP 11
STEP 12
Connect the DC plug on the splitter cable into the base of Electric Stand (A). Connect USB
coming from the desk control panel into the base of Electric Stand (A). Make sure the USB
cord is ran outside of the cable clip. Refer to the frame manual to plug in the remaining
cables.
A
S-B
S-C
H
Slide monitors onto tilt joint located on the arm assembly. Lock VESA plate (H) in place
with Screw Cap (S-B), M3x8mm Screw (S-C) and a Phillips Screwdriver. Adjust monitor
height alignment by turning Screw Cap (S-B) by hand or using 6mm Allen Wrench (T-B).
Note: If you are having an issue with a monitor tilting down once installed on the arm,
refer to Step 17 to tighten down the tilt joint.
Control Panel
DC Plug Splitter Cable
USB
T-B
9
STEP 13
Initial Setup Procedure:
Referring to the control panel instruction manual, ensure the panel display is set to adjust
frame height (see the “Shi Device Display” section) and move your desk frame to a
comfortable level for your normal sitting position. It is recommended to follow general
ergonomic guidelines for working posture while considering your desk frame height. Store
this position in memory setting 1.
Next, with the electric stand at its lowest height setting, loosen the arm bracket screw
using the 6mm Allen Wrench (T-B) and manually adjust the arm assembly along the
electric stand post until the top of the monitor screen is at eye level while in your normal
sitting position. If this is not possible due to being taller or shorter than average, simply
position the arm assembly at the very top or the very bottom of the electric stand post
respectively. Re-tighten the arm bracket screw to secure the arm assembly in this position.
Note: You do not have to use the monitor at this height, but doing so reduces the amount
of manual adjustment later on.
T-B
10
STEP 14
Setting Memory Positions:
Referring to the control panel instruction manual, ensure the panel display is set to adjust
stand height. In your normal sitting position, move the stand until the monitors are at a
comfortable level, switching between frame and stand adjustment on the panel display
as necessary. It is recommended to follow general ergonomic guidelines for work posture
while considering the optimal height of your monitors. Store this position in memory
setting 1. Your desk and monitor height should both now be synced to memory setting 1.
Referring to the control panel instruction manual, move your desk frame and monitor to
a comfortable standing position, switching between frame and stand adjustment on the
panel display as necessary. Store these height locations to memory setting 2. Repeat this
procedure for storing a third working posture in memory setting 3 if desired.
Andere Handbücher für STAND-E-102B
2
Inhaltsverzeichnis
Andere Vivo Rack & Stand Handbücher
Vivo
Vivo MOUNT-PC06E Bedienungsanleitung
Vivo
Vivo STAND-V001E Bedienungsanleitung
Vivo
Vivo MOUNT-CR70C Bedienungsanleitung
Vivo
Vivo STAND-V102AM Bedienungsanleitung
Vivo
Vivo STAND-V002 Bedienungsanleitung
Vivo
Vivo MOUNT-VP01B Bedienungsanleitung
Vivo
Vivo MOUNT-HP01M Bedienungsanleitung
Vivo
Vivo STAND-TV07-S Bedienungsanleitung
Vivo
Vivo MOUNT-CUB1 Bedienungsanleitung
Vivo
Vivo MOUNT-V00MIC Bedienungsanleitung
Vivo
Vivo MOUNT-PS02V Bedienungsanleitung
Vivo
Vivo MOUNT-SF004 Bedienungsanleitung
Vivo
Vivo STAND-V011 Bedienungsanleitung
Vivo
Vivo MOUNT-XSXU1 Bedienungsanleitung
Vivo
Vivo STAND-V100F Bedienungsanleitung
Vivo
Vivo MOUNT-PLAY1W Bedienungsanleitung
Vivo
Vivo PT-SD-AM01K Bedienungsanleitung
Vivo
Vivo DESK-V133E Bedienungsanleitung
Vivo
Vivo STAND-V006F Bedienungsanleitung
Vivo
Vivo STAND-SIT1WD Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
