Vivotek FD8361L Bedienungsanleitung
Quick Installation Guide
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:+886-2-82455282|F:+886-2-82455532|E:[email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298|E: [email protected]
IR Illuminators • 3-axis • Video Cropping • ePTZ
All specications are subject to change without notice.
Copyright 2012 VIVOTEK INC. All rights reserved.
c
P/N:625012601G Rev. 1.1
FD8361L Fixed Dome
Network Camera
EN - 1
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Contact your distributor in the event of
occurrence.
Refer to your user's manual for the
operating temperature.
Warning Before Installation
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not insert sharp or tiny objects
into the Network Camera.
Do not drop the Network Camera.
EN - 2
Software CD
FD8361L
Quick Installation Guide /
Warranty Card
Alignment Sticker / Ceiling Hole Template Sticker
Bottom Base
5
1
0
0
0
0
2
1
1
G
Package Contents
1
L-type Hex Key Wrench / RJ45 Female/Female Coupler / Silica Gel / Screws
Quick Installation Guide
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
IR Illuminators • 3-axis • Video Cropping • ePTZ
All specications are subject to change without notice.
Copyright 2012 VIVOTEK INC. All rights reserved.
c
P/N:625012601G Rev. 1.1
FD8361L
Fixed Dome
Network Camera
Ceiling Hole Template Sticker
Drill hole
EN - 3
English
SD/SDHC Card Slot
IR LEDs (18 units,
distance 20m)
Recessed Reset
Button
AC24V
AC24V
Focus Controller
Zoom Controller
Status LED
Light Sensor
Physical Description
2
Pan Adjustment Screw
Inner View
Ethernet 10/100 RJ45 Plug
AC 24V Terminal Block
Ground
Fan
Operating environment: -20° ~ 50°C
When the temparature inside the Network
Camera reaches over 50°C, the fan will operate
automatically; when the temparature inside the
Network Camera drops to 0°C, the heater and fan
will both operate automatically.
BNC Video Output
Heater
Rotation Adjustment
Screw
Vari-focal Lens
(f= 3~9 mm)
Tilt Adjustment Screw
NTSC/PAL Video Output
Switch
EN - 4
Record the MAC address under
the camera base before installing
the camera.
Network Camera
Model No: FD8361L
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
RoHS
V I
MAC:0002D1083236
CLASS A
IP66-rated Vandal-proof
Bottom Base
Outer View
IP66-rated Vandal-proof
Dome Cover
AC24V
AC24V
Camera Base
a
b
c
Hole a~c:
Holes to secure the bottom base.
a
b
c
EN - 5
English
First, use a screwdriver to loose the three screws and detach the dome cover from the
camera base. Then, follow the steps below to install the camera to either a ceiling or a wall.
Hardware Installation
3
Ceiling mount (with the bottom base)
1. Attach the supplied alignment sticker to the ceiling.
2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the ceil-
ing. Then hammer the four supplied plastic anchors into the holes.
3. Through the four holes on the bottom base, insert the four supplied screws into the corresponding
holes and secure the bottom base with a screwdriver.
4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a
screwdriver.
5. Secure the camera base to the bottom base with three supplied screws.
AC24V
AC24V
1
2
3
45
A
B
EN - 6
Wall mount (with the bottom base)
1. Attach the supplied alignment sticker to the wall.
2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall.
Then hammer the four supplied plastic anchors into the holes.
3. Using the four holes on the bottom base, insert the four supplied screws to corresponding holes and
secure the bottom base with a screwdriver.
4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a
screwdriver.
5. Secure the camera base to the bottom base with three supplied screws.
1
2
3
5
A
B
4
EN - 7
English
General Connection (without PoE)
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
AC24V
AC24V
Network Deployment
4
1. Connect the power cable to the AC 24V terminal block.
2. Use the supplied RJ45 female/female coupler
to connect the Network Camera to a switch.
Use a Category 5 Cross Cable when Network
Camera is directly connected to PC.
AC24V
AC24V
AC24V: Power in AC 24V
AC24V: Power in AC 24V
Drop-ceiling mount (without the bottom base)
1. Attach the supplied ceiling hole template sticker to the ceiling.
2. Open a hole along the inner circle of the sticker.
3. Using the 3 circles on the sticker, drill 3 pilot holes into the ceiling. Then hammer the three supplied
plastic anchors into the holes.
4. Mount the Network Camera to the ceiling and feed the cables through.
5. Using the three holes on the side of the camera base, insert the three supplied screws into the cor-
responding holes and secure them with a screwdriver.
1
5
23
4
Ceiling Hole Template Sticker
Drill hole
EN - 8
Power over Ethernet (PoE)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
AC24V
AC24V
PoE Switch
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
AC24V
AC24V
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a
single Ethernet cable. Follow the below illustration to connect the Network Camera to a
PoE-enabled switch via Ethernet cable.
Non-PoE Switch
PoE Power Injector
(optional)
EN - 9
English
Network Camera
Model No: FD8361L
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
RoHS
V I
MAC:0002D1083236
CLASS A
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is
analyzed, please click on the “Next” button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches the
one labeled on the bottom of your device to connect to the Network Camera via Internet
Explorer.
0002D1083236
00-02-D1-08-32-36 192.168.5.109 FD8361L
Installation
Wizard 2
Assigning an IP Address
5
Andere Handbücher für FD8361L
3
Inhaltsverzeichnis
Andere Vivotek Sicherheitskamera Handbücher
Vivotek
Vivotek SD8364E/ -M Bedienungsanleitung
Vivotek
Vivotek NetworKam IP3111 Bedienungsanleitung
Vivotek
Vivotek PT3113 Bedienungsanleitung
Vivotek
Vivotek FE8173 Bedienungsanleitung
Vivotek
Vivotek FD8133V Bedienungsanleitung
Vivotek
Vivotek IP7142 Bedienungsanleitung
Vivotek
Vivotek IB8377-H Bedienungsanleitung
Vivotek
Vivotek PZ8111 Bedienungsanleitung
Vivotek
Vivotek 4X-IP7133 Bedienungsanleitung
Vivotek
Vivotek IP8336W Bedienungsanleitung
Vivotek
Vivotek CD8371-HNTV Bedienungsanleitung
Vivotek
Vivotek MD7560 Bedienungsanleitung
Vivotek
Vivotek FE8174 Bedienungsanleitung
Vivotek
Vivotek PT8133 Bedienungsanleitung
Vivotek
Vivotek Supreme IP8151 Bedienungsanleitung
Vivotek
Vivotek Supreme IP9165-HT-v2 Bedienungsanleitung
Vivotek
Vivotek IP7138 Bedienungsanleitung
Vivotek
Vivotek FD8361L Bedienungsanleitung
Vivotek
Vivotek IP8335H Bedienungsanleitung
Vivotek
Vivotek FD8154 Bedienungsanleitung
