Vivotek IP9165-LPC Bedienungsanleitung
IP Surveillance
Installation Guide
IP9165-LPC
License Plate Capturing Solution
Highway & Street
Rev. 1.0
Ordering part no.:
IP9165-LPC (Highway): 199004200G
IP9165-LPC (Street): 199004100G
Document part no.: 625046000G
2
Specications
I
Model Number LPC enclosure
Power Input 24V AC
Max. Output power budget 48W (Street); 80W (Highway)
Power Consumption Window heater: 10W; Blower: 2W; Camera: 6 ~ 8W
Environmental Operation Temp. -20°C ~ +50°C (-4°F ~ +149°F)
Protection Level IP68, IK10
Mounting Bracket Fully-cable Management
Construction Die-cast Aluminum Alloy
Coating White epoxy powder coating
Dimensions 502.8 (L) x 170 (W) x 400 (H) mm
Net Weight 6,482g (9.24 lb)
CAUTION:
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
UNPACKING:
Unpack carefully. Electronic components can be damaged if improperly handled or
dropped. If an item appears damaged in shipment, place it properly in its carton and
notify the shipper.
IMPORTANT!:
1. Read and follow Instructions: All operating and user instructions should be read and
followed before the unit is to be operated.
2. Electrical Connections: Only a qualied electrician is allowed to make electrical
connections.
3
English
Please note the following for different applications:
If you use IP9165-LPC for parking area or highway, you must select the LPR
scene mode.
Depending on the car speed at your surveillance scene, please select an
appropriate scene mode:
Maximum car speed Scene mode
50km/hr (32mph) LPC-Parking Lot
90km/hr (55mph) LPC-Street (default)
180km/hr (110mph) LPC-Highway
The Scene mode option can be found in Application > Media > Image
settings.
4
Mounting Conguration & Dimensions
II
Swivel Positions and Directions
105 mm
502.8 mm
135.5 mm
158.5 mm
170 mm
400 mm
77.4 mm
USABLE
AREA
255 mm
USABLE AREA
400
170 502.8
5
English
Installation Suggestions
IV
If you plan to install this camera enclosure into a tropical, sea coastal, or an environment
where salt water or corrosive industrial waste water/moist are present, please seal each
stainless steel screws and ttings with a silicon grease compounds. This will help prevent
electrolysis to occur and extend the life span of the camera and housing.
IMPORTANT:
1. Disconnect devices: A readily accessible disconnect device in the building installation wiring
should be incorporated.
2. Electrical Connection: Only a qualied electrician is allowed to make electrical connections.
Component Description
III
Camera Mounting Platform
M16 1/2" Waterproof cable gland
Power distribution
board
Ventilation fan Window frame heater
coil
• Please avoid eye exposure or apply appropriate protection, such as wearing a pair of Infrared
protection glasses, when working with the product. Always use camera live view to oberve IR
lighting effects.
WARNING:
6
Installation
V
1. Install the wall-mount bracket to a preferred location at your installation site. Drill
mounting holes and a cable routing hole (if preferred) on a wall. Install the bracket.
Prepare and route the wiring, Ethernet and 24V power source.
2. Install the IR illuminator to the bottom of the housing. Attach the included grip stricker
to the U bracket.
7
English
3. Secure the U bracket to the IR illuminator using the included wrench and hex screws.
4. Flip the housing over and place it on a clean, stable surface. Secure the IR illuminator
to the bottom of the housing using the included wrench and a hex socket screw.
8
6. Prepare power wires, a ground wire, and a CAT5e Ethernet cable. Pass them through
the M16 waterproof connectors under the housing.
Ethernet cable Ø4 ~ 6.5mm
Power wires & DI/DO wires,
a combo cable from IR illuminator
(if applied)
5. You can turn the IR illuminator so that its at side is parallel with the housing, and that
you can turn the assembly over and work on the inside of the housing. Put a foam pad
below before you work on the wiring to avoid scratching the surface.
9
English
7. When done, tighten up and install the waterproof connectors.
8. Assemble the camera components, e.g., the CS ring and lens module. Secure the
mounting plate to the bottom of the camera (the label side) using the included screw.
There is a plastic mount pad in the package. You do not need the mounting pad
using the VIVOTEK camera.
o
O
g
B
b
G
br
BR
1
2
3
4
5
6
7
8
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
You may need to remove the RJ45 connector, and use a crimping tool to connect the
Ethernet wires to an RJ45 connector inside the enclosure. Use an Ethernet cable of the
width of 4 ~ 6.5mm.
10
Lens flush
w/ edge of
enclosure
9. Adjust the camera's position so that the lens module can ush align with the tempered
glass. Secure the camera using the screws and washers to the bottom of the housing.
10. Connect 24V power source to the power input terminal. Connect power wires from
the DC 12V output to the camera. Connect the 24V power output to drive the external IRs.
Heater
Blower
IR angle selector
(Not used for this model)
I/O terminal block
(Not used for this model)
Camera heater
24V AC/DC IN 12V DC OUT
24V AC/DC OUT
Connectors to the front IR
(Not used for this model)
Power LED
Andere Handbücher für IP9165-LPC
1
Inhaltsverzeichnis
Andere Vivotek Sicherheitskamera Handbücher
Vivotek
Vivotek IB8360-W Bedienungsanleitung
Vivotek
Vivotek IP7151 Bedienungsanleitung
Vivotek
Vivotek SUPREME use IP FE9582-EHNV Bedienungsanleitung
Vivotek
Vivotek Vortex IB639 Series Bedienungsanleitung
Vivotek
Vivotek IP8173H Bedienungsanleitung
Vivotek
Vivotek IP8364-C Bedienungsanleitung
Vivotek
Vivotek IP3136 Bedienungsanleitung
Vivotek
Vivotek CC8130 Bedienungsanleitung
Vivotek
Vivotek IP8364-C Bedienungsanleitung
Vivotek
Vivotek IB8360 Bedienungsanleitung
Vivotek
Vivotek IP7160 Bedienungsanleitung
Vivotek
Vivotek IB8373-EH Bedienungsanleitung
Vivotek
Vivotek PZ7111 Bedienungsanleitung
Vivotek
Vivotek MD8563-EHF4 Bedienungsanleitung
Vivotek
Vivotek PT7135 Bedienungsanleitung
Vivotek
Vivotek IB9369 Series Bedienungsanleitung
Vivotek
Vivotek FD8133V Bedienungsanleitung
Vivotek
Vivotek PD8136 Bedienungsanleitung
Vivotek
Vivotek IP8152 Bedienungsanleitung
Vivotek
Vivotek MS9321-EHV Bedienungsanleitung
