VOGELS PFW 6851 Bedienungsanleitung

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

Maximum Flat Panel Weight:

175 lb. / 79.37 kg.

PFW 6851

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

www.vogels.com

Included components

Required for installation

Swingout Mount

Channel Covers

Mounting

Bracket

Griplate™

Washer

5/16" Flat

Washer

Universal

Spacers

Thread Depth

Indicator

(Supplied)

Extension Adapter M8 Nylon Nut

5/16" x 3"

Lag Bolt

M4 x 16mm M4 x 25mm M4 x 30mm

M6 x 16mm M8x 16mm M8 x 25mm M8 x 30mm

M6 x 25mm M6 x 30mm

x1 x1 Pair x8

x4 x4 x4 x4 x4

x4 x4 x4

x4 x4 x4 x4 x1 x4 x4

M6 or 1/4"

Wood Drill bit

3/8" Masonry

Drill bit

13mm or 1/2"

Socket

Finned Anchor

Level

You must secure the mount to two (2) wall studs with a minimum of four

(4) lag bolts (2 lag bolts for each stud found).

Minimum of 2 x 4 wood stud to be used

Wood Installation

Directional Mounting Arrow

The Directional Mounting Arrow stamped into the PFW 6851 Mount

indicates which edge is the top.

Mounting Safety

Two people are recommended for this step

Introduction

Page 2

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

Two people are recommended for this step; one person to level the

Mount and another person to mark the wall stud location.

1) Place the mount against the wall in the desired viewing location.

2) Adjust the mount to align the mount slots in the wall plate with the center

of the wall studs.

3) Level the mount.

4) Use a pencil to mark the upper right mounting location along the center of

the wall stud.

Drill a “pilot hole” in the center of the upper right mark using a 1/4" drill bit and

power drill.

Only use a 1/4" drill bit when drilling pilot holes.

1) Place the Mount against the wall and align it with the pilot hole.

2) Insert one (1) 5/16"x 3˝ lag bolt and one (1) 5/16" washer into the upper

right pilot hole.

3) Use a socket wrench and a 1/2" socket to tighten the lag bolt.

Do not over tighten the lag bolt.

Page 3

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

1) Level the Mount.

2) Use a pencil to mark the remaining three (3) mounting locations along the

center of each wall stud.

Two people are recommended for this step; one person to level the

Mount and another person to drill the pilot holes.

Drill a “pilot hole” in the center of each of the marks with a power drill and a

1/4" drill bit.

Only use 1/4" drill bit when drilling the pilot holes.

1) Insert one (1) 5/16" x 3" lag bolt and one (1) 5/16" washer into each pilot holes.

2) Tighten all lag bolts using a socket wrench and 1/2" socket.

Do not over tighten the lag bolts when attaching the mount to the wall.

Improper installation may result in personal injury or property damage.

Page 4

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

Two people are recommended for this step: one person to

level the mount and another person to mark the mounting

locations.

Concrete Installation

5/16" Flat Washer 5/16" x 3" Lag Bolt

x4 x4

Insert the lag bolts and washers into the Finned anchors.Tighten all lag

bolts using a socket wrench and 1/2″ socket.

Do not over tighten the lag bolts.

Drill four (4) pilot holes of each mark using a drill and 3/8” masonary drill

bit. Drill 3 inches deep.

Only use a 3/8" masonary drill bit when drilling pilot holes.

Insert a Finned Anchor into each hole. Lightly tap each Finned Anchors

into place with a hammer.

Finned Anchor

Page 5

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

Selecting the Mounting Hardware

1) Insert a small straw or toothpick into the threaded inserts found

on the back of the at panel.

2) Use a pencil to mark the depth of the threaded insert on the small

straw or toothpick.

3) Mark the straw or toothpick 1/8” above the depth of the threaded

insert, as shown in Figure 1.

4) Insert the small straw or toothpick into the remaining threaded

inserts to compare and verify their depth using the straw or

toothpick’s 1/8” allowance mark.

5) Locate the correct diameter screw for the threaded insert.

If the screw you selected is longer than the 1/8” allowance

mark on the small straw or toothpick, as shown in Figure 2 and

Figure 3, do not use this screw. The screw length must not

bypass the mark.

6) Test each size of the screws provided.

The correct screws should thread easily into the mounting

point and not pull out when tension is applied.

1˝ ¼˝

Flat Panel

Universal Washer

Universal Spacer

Mounting Bracket

Mount Point

Mounting Screw

Universal Spacers allow you to attach the mounting bracket to at-panels which

have recessed or uneven mount points. Each Universal Spacer adds 1/4” to the

distance between the mounting bracket and your at-panel.

The Universal Spacers must be stacked and oriented as shown.

The Universal Spacers must only be installed between the mounting

bracket and your at-panel.

Universal Spacer Installation (Optional)

If your at panel has uneven mounting points, or recessed

mounting points, please use the provided universal spacers.

Page 6

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

Universal Washer Installation

Universal Washers are designed to accommodate the various M4, M6,

and M8 hole sizes required by at panels.

Do not place excessive pressure on the back of the at panel,

as this may damage your at panel.

The Universal Washer must be installed between the head of

the mounting screw and the mounting bracket as shown.

1) Place your at panel screen-side down on a soft, at surface.

2) Identify the number and location of the thread inserts on the back

of your at panel.

3) Aligning the holes on each mounting bracket with the thread

inserts on the back of your at panel.

4) Secure each mounting bracket to your at panel by inserting a

minimum of two (2) screws per bracket.

Do not over tighten the mounting hardware.

DIMPLES

FACING UP

DIMPLES

FACING DOWN

DIMPLES

FACING UP

DIMPLES

FACING DOWN

Mounting Hardware

Mounting Bracket

Mounting Point

Universal Spacer

Flat

Griplate™

Mounting Bracket Installation

Page 7

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

The adapter plate can be used with mounting patterns from 200mm x 200mm x to 650mm x 840mm.

In the event that you're at panel has recessed or uneven mounting surface, universal spacers may be stacked to achieve proper spacing. Select the amount

of universal spacer (s) that is closest in depth to keep your adapter plate as close to the at panel as possible. The universal spacer must be secured between

the at panel and the adapter plates.

Do NOT over tighten the screws.

Step 1. Determine if your at panel will need the

adapter plates.

Step 2. Locate the mounting points on the back

of the at panel.

Step 3. Using a screwdriver, insert and tighten the

mounting hardware and adapter plates to the

back of the at panel. Do not over tighten the

screws.

Step 4. Place the universal mounting brackets over the

threaded mounting studs that are on the

adapter plate.

Step 5. Place one (1) 5 / 16" at washer onto each

threaded mounting stud.

Step 6. Thread one (1) M8 Nylon nut onto each threaded

mounting stud.

Step 7. Once the universal mounting brackets are level,

use a 1/2" socket and socket wrench to tighten

the M8 nylon nuts. Do not over tighten the

screws.

Before tightening the nylon nut, be sure that both universal

mounting bracket are level and aligned with each other.

If they are not aligned and level, the at panel will not sit

properly when mounted to the PFW 6851

Adapter Plate

Griplate

Mounting Hardware

Flat Panel

Adapter Plate

Socket Wrench

Nylon Nut

Flat Washer

Universal Mounting

Bracket

Adapter Plate Installation (Optional)

Page 8

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

Upper Mounting Bar

Lower Mounting Bar

Flat Panel

Two people are required for this step.

Step 1. Place the universal brackets and the at panel over and onto the upper and lower mounting bars of the PFW 6851 and lower it down. Do not release the at

panel until the at panel is resting securely on the upper and lower mounting bars.

Screwdriver

Leveling Screw

(Pre-installed)

Locking Screw

(Pre-installed)

Step 1. Use a screwdriver to adjust the two (2) M6 x 30

leveling screws, located on the top of the mounting

brackets.

Step 2. Once the at panel panel is level, ues a screwdriver

to tighten the two (2) M6 x 30 locking screws,

located on the bottom of the mounting brackets. Do

not over tighten these screws.

Attaching the Flat Panel to the Wall Plate

Securing the Leveling the Flat Panel

Do not release the at panel until verifying the connection

between the universal brackets and the upper and lower

mounting bars.

In the event that the at panel is tilted too far to one

side, the leveling screws will allow you to compensate

for this tilt by simply adjusting the screws with a screw-

driver (see illustration to the right for a clear view).

Page 9

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6851

www.vogels.com

Ajusting the Flat Panel Tilt

Plastic Channel Cover Installation

TO ADJUST THE TILT TENSION OF THE PFW 6851, LOOSEN THE TENSION BOLTS LOCATED ON THE BOTTOM RIGHT AND LEFT SIDE OF THE

MAIN ARM ASSEMBLY. RE-TIGHTEN THESE BOLTS TO ACHIEVE YOUR DESIRED TENSION.

Tension

Bolt

Tension

Bolt

Adjusting the Flat Panel Down Adjusting the Flat Panel Down

Step 1. Place one hand at the center top edge of

the at panel.

Step 2. Place the other hand on the center bottom

edge of the at panel.

Step 3. Using the upper hand, gently pull the top

of the at panel away from the wall while

the lower hand gently pushes the bottom of

the at panel towards the wall.

Step 1. Place one hand at the center top edge of

the at panel.

Step 2. Place the other hand on the center bottom

edge of the at panel.

Step 3. Using the upper hand, gently push the top

of the at panel towards the wall while

the lower hand gently pulls the bottom of

the at panel towards the wall.

Side Cover

(Long)

Center Cover

(Short)

Side Cover

(Long)

Step 1. Place the plastic channel covers over the

Mounting plate (2 side covers and 1 center cover).

Step 2. Gently push each cover into place, covering the mounting

slots of the mounting place.

Repeats steps 1 and 2 for the installation for

of the lower plastic channel covers.

Page 10 95V0-000-016-0X_1

Andere Handbücher für PFW 6851

Inhaltsverzeichnis

Andere VOGELS Rack & Stand Handbücher

VOGELS

VOGELS SWM 4131 Series Bedienungsanleitung

VOGELS

VOGELS THIN 245 Bedienungsanleitung

VOGELS

VOGELS VFWE 552 RC Bedienungsanleitung

VOGELS

VOGELS EFA 8825 Bedienungsanleitung

VOGELS

VOGELS PPA 370 Bedienungsanleitung

VOGELS

VOGELS PFA 9141 Bedienungsanleitung

VOGELS

VOGELS THIN 325 Bedienungsanleitung

VOGELS

VOGELS W5207X Bedienungsanleitung

VOGELS

VOGELS PPT 2300 Bedienungsanleitung

VOGELS

VOGELS TVM 3840 Series Bedienungsanleitung

VOGELS

VOGELS THIN RC 35 Bedienungsanleitung

VOGELS

VOGELS NEXT 7346 Bedienungsanleitung

VOGELS

VOGELS PFW 6854 Bedienungsanleitung

VOGELS

VOGELS W5305 Series Bedienungsanleitung

VOGELS

VOGELS TVM 5405 Series Bedienungsanleitung

VOGELS

VOGELS WALL 2325 Bedienungsanleitung

VOGELS

VOGELS THIN 225 Bedienungsanleitung

VOGELS

VOGELS SOUND 3200 Bedienungsanleitung

VOGELS

VOGELS EFW 8145 Bedienungsanleitung

VOGELS

VOGELS EFW 8125 Bedienungsanleitung

VOGELS

VOGELS EPA 6505 Bedienungsanleitung

VOGELS

VOGELS THIN 345 Bedienungsanleitung

VOGELS

VOGELS COMFORT TVM 3460 Series Bedienungsanleitung

VOGELS

VOGELS PFW6855 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung