VOGELS PFW 6854 Bedienungsanleitung

Display Wall Mount, Rotating

MOUIN_PFW6854_V02

Max: 72kg/160lbs

PFW 6854

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione,

Guide d’Installation, Installatie gids

Page 2 Installation Instructions

Table of Contents

PFW 6854

Parts List 2

Installation Tools 3

Thread Depth Indicator 6

Mount Installation 7

Concrete Mounting 8

Universal Mounting Bracket Installation 8

Display Orientation 10

Technical Specications 10

Lock-it Security Manual 11

Parts List

This mount is shipped with all installation hardware and components. Make sure that none of these parts are

missing and/or damaged before beginning installation.

Griplate™ (Qty 8)

5/16” x 3” Lag Bolts - wooden studs

only (Qty 6)

5/16” Flat Washers

(Qty 4)

Universal Mounting Brackets (Qty 2) Rotating Universal Bracket Bar (Qty 1)

M6 Knurl Knob

(Qty 1)

PFW 6854 Mounting Bracket (Qty 1)

Finned Anchors M10 x 60

(Qty 6)

Installation Instructions Page 3

Installation Tools

Phillips Head Screw Driver Soft Material/Blanket 1/2” Socket and Wrench

Pencil Tape Measure Drill Gun

Level (Supplied) M5 Allen Wrench (Supplied) 5/32” Allen Wrench (Supplied)

1/4” Drill Bit (Pilot Holes) Thread Depth Indicator (Supplied)

Masonry Drill Bit (Concrete Applications - Commercially Available)

PFW 6854

Qty 8

Qty 4

M6 x 45

M8 x 20

M8 x 25

M8 x 30

M8 x 35

M8 x 45

M8 x 70

M4 x 16

M4 x 25

M5 x 12

M5 x 16

M5 x 20

M5 x 25

M5 x 50

M6 x 16

Qty 8

Qty 7

M6 x 20

M6 x 30

Page 4 Installation Instructions

PFW 6854

The nylon spacers may be stacked to achieve proper spacing.

5/16" Flat washers

(metal)

1/4" Nylon spacers

(Qty 8)

(small)

(Qty 8)

1/2" Nylon spacers

1/4" Nylon spacers

(Qty 12)

(large)

(Qty 8)

(large)

(Qty 8)

Nylon sleeves

9/16" Nylon spacers

(Qty 8)

1" Nylon Spacers

(Qty 8)

Installation Instructions Page 5

PFW 6854

Thread Depth Indicator

1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the at panel to make sure the inserts

measure the same full depth and mark it (Figure 1).

2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied).

3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw.

4. The screw length must not bypass the marking. Select another screw size (Figure 2 and 3), until you nd one that comes closest to

your mark without going past.

Thread Depth

Indicator

Marking

Screw

Marking

Screw

Thread Depth

Indicator

Inverted Flat

Panel Display

Marking the

Depth

Thread Insert

Thread Depth

Indicator

Figure 1

Figure 2 Figure 3

Page 6 Installation Instructions

PFW 6854

Mount Installation

Determine where the mount lo-

cation will be. Use a stud nder

to locate the nearest wall stud.

Once the stud has been located, use a

pencil to mark the spot.

Using a 1/4” drill bit, drill the upper mount-

ing hole where the mark was made.

Step 1 Step 2 Step 3

For ease of installation, it is recommended that two people perform the installation. One person should hold

the mount while the other person installs the lag bolt and washer. Making sure that the mount is level, the

person not holding the mount must mark and drill the second mounting hole and secure the second lag bolt

and washer.

Place a level (supplied) on the top

rail and make sure that the mount is

level. Once the mount is level, Drill

pilot holes in the lower mount-

ing slots and install two (2) 5/16” x

3” lag bolts and washers into the

mounting holes and tighten.

Step 6

Step 5

Step 4

Insert two (2) 5/16” x 3” lag bolts

and washers into the mounting

holes and tighten (see WARNING:

below

After the holes have been pre-drilled,

line up the mounting slot openings

with the pre-drilled holes.

If the studs are 12” (304.8mm) apart, use three (3) 3” (76.2mm) lag bolts for the top rail and three (3) 3” (76.2mm)

lag bolts for the lower rail. If the studs are 16”(406.4mm), 18” (457.2mm) or 24” (609.6mm) apart, use two (2) 3” lag

bolts for the top rail and two (2) 3” lag bolts for the lower rail.

Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal

injury or damage to property.

Installation Instructions Page 7

PFW 6854

Concrete Mounting

Concrete anchors must be used for concrete installation. They can be purchased at your local hardware store. The

mounting surface must be a minimum 6” thick.

For the two upper mounting points, the Griplate™ at side must be facing up. For the two lower mounting points,

the Griplate™ at side must be facing down.

IT WILL TAKE TWO PEOPLE TO COMPLETE THE NEXT INSTALLATION STEP.

1. Begin by placing the mount into position against the wall, keeping it level.

2. Mark off four holes to be used for securing the mount.

3. Next, drill holes using a masonry bit for your anchors (recommended masonry bit).

4. Insert a commercially available concrete anchor into each hole (recommended 3/8” anchors).

5. If necessary, a hammer can be used to lightly tap each anchor into place so that they are ush with the wall.

6. Once all of the anchors are in place, move the wall bracket into position.

7. Attach the nut onto the threaded shaft that is protruding from the wall.

8. Do not tighten until all nuts are in place.

5. At this time, center the universal bracket bar and tighten the set screws that are located on the universal brackets.

Universal Mounting Bracket Assembly

1. Place the universal bracket bar and the universal brackets on a at surface.

2. Slide the universal brackets onto the universal bracket bar (as shown below) with the set screws facing up. At this

time, do not tighten the set screws that are located on the universal bracket.

3. Place the display on a soft, at surface, face-down. Next, place the universal bracket assembly on the back of the

display, with the universal brackets resting directly over the display mounting points.

4. Once the desired position has been determined, place the Griplate™ washers over each mounting point and secure

them using the appropriate hardware (see Page 5).

Universal Mounting Brackets

Set Screw

Griplate™ Universal Bracket Bar Griplate™

DIM PLES

FACING UP

D IM PLES

FACING DOW N

D IM P L E S

FACING UP

D IM PLES

FACING DO W N

Page 8 Installation Instructions

PFW 6854

After loosening the tension bolts, be sure that

the nose piece is held together tightly before

rotating.

6. Lower the universal bracket bar with attached

display into the cradle (as shown to the left).

Nylon

Sleeve

Knurl Knob Mounting Point/M6 x 12mm Security Head and

M6 Lock Washer Mounting Point.

7. Insert an M6 Knurl Knob/M6 x 12mm Security

Head and M6 Lock Washer into the knurl knob/

security screw mounting point and tighten.

To access the knurl knob/security screw

location while the display is attached, the

PFW 6854 must be rotated to the “portrait”

position (vertical position

8. Tighten the two (2) Phillips head screws (located

on the side of the mounting block) once the nal

position is attained.

Locking Screws

Installation Instructions Page 9

PFW 6854

Display Orientation

The PFW 6854 will allow the user to adjust the display a full 360°.

BEFOREROTATINGTHEPFW6854,MAKESURETHATTHEM6KNURLKNOBISSECURELYFASTENEDTOTHE

PFW6854.ALSO,PLEASEMAKESUREYOUALLOWENOUGHCABLEANDWIRECLEARANCEFORFULLROTATION.

1. To adjust the PFW 6854, rotate the display

either clockwise or counter-clockwise.

M6 Knurl Knob

2. Tighten the two Phillips head locking

screws (see Step 8, Page 10)

Technical Specications

All measurements are in inches (mm).

Page 10 Installation Instructions

PFW 6854

Lock-It™ Security Hardware Pack

The PFW 6854 is shipped with a safety knurl knob already installed. If the user decides to incorporate the optional security hardware,

the following steps will show the user how to effectively remove the safety knurl knob and install the optional Lock-It™ hardware

kit.

NOTE: The M6 security head screw will be installed after the PFW 6854 has been fully assembled. Installation

of the M6 security head screw prior to completing assembly will not allow the PFW 6854 to function properly.

M6 x 12mm

Security Head

Screw (Qty 1) and

Lock Washers

(Qty 2)

Security Allen

Wrench

(Qty 1)

Step 1

Remove the PFW 6854 from the packaging and

remove the existing safety knurl knob. Remove the

universal bracket bar.

Step 2

Place the two lock washers onto the M6x12mm security head

screw. Place the M6x12mm security head screw onto the

security allen wrench and insert into mounting point.

Step 3

Once inserted into the mounting point, fully tighten

into place using the security Allen wrench.

Step 4

Once the M6 security head screw has been installed, re-insert

the safety knurl knob. Installation completed. This will prevent

the display from being removed from the assembly.

Allen

Wrench

Safety Knurl

Knob

M6 Security Head Screw

and Lock Washers

Universal

Bracket Bar

Safety Knurl

Knob

M6 Security Head Screw

and Lock Washers

Inhaltsverzeichnis

Andere VOGELS Rack & Stand Handbücher

VOGELS

VOGELS THIN 550 Bedienungsanleitung

VOGELS

VOGELS WALL 2105 Bedienungsanleitung

VOGELS

VOGELS EFW 8145 Bedienungsanleitung

VOGELS

VOGELS SOUND 3400 Bedienungsanleitung

VOGELS

VOGELS PFA 9141 Bedienungsanleitung

VOGELS

VOGELS THIN 325 Bedienungsanleitung

VOGELS

VOGELS W52080 Bedienungsanleitung

VOGELS

VOGELS EFW 8145 Bedienungsanleitung

VOGELS

VOGELS EFF 1140 - BLACK PACKAGING STICKER Bedienungsanleitung

VOGELS

VOGELS VFW 232 - VFW 332 VFW 432 Bedienungsanleitung

VOGELS

VOGELS PFA 9033 Bedienungsanleitung

VOGELS

VOGELS INT8201 Bedienungsanleitung

VOGELS

VOGELS PFA 9134 Bedienungsanleitung

VOGELS

VOGELS RISE 5105 Bedienungsanleitung

VOGELS

VOGELS NEXT 7346 Bedienungsanleitung

VOGELS

VOGELS MOMO Motion+ 4127 Bedienungsanleitung

VOGELS

VOGELS EFW 8206 Bedienungsanleitung

VOGELS

VOGELS TVM 5440 Series Bedienungsanleitung

VOGELS

VOGELS EFA 8825 Bedienungsanleitung

VOGELS

VOGELS EFA 8825 Bedienungsanleitung

VOGELS

VOGELS W5207X Bedienungsanleitung

VOGELS

VOGELS PFW6857 Bedienungsanleitung

VOGELS

VOGELS PFW 6875 Bedienungsanleitung

VOGELS

VOGELS EFW 8125 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung