Vollrath Onion King 502N Bedienungsanleitung

Installation Instructions

Onion King®Blade Replacement

TOOLS YOU WILL NEED

WASH THE NEW BLADE ASSEMBLY

Wash new blades with warm, soapy water and rinse thoroughly to

remove the thin protective oil film.

NOTICE: Keep the sharp edge away from you when handling blades.

WHICH ONION KING™ SLICER DO YOU HAVE?

Inspect your slicer to determine which slicer you have.

REMOVE THE OLD BLADE ASSEMBLY

1. Remove the screws and washers or plates from the long leg side of

the base.

2. Remove the screws, washer plates, and o-rings from the short leg

side.

3. Remove the blade assembly by lowering it through the frame.

4. Retain the screws and o-rings for installing the new blade assembly.

INSTALL THE NEW BLADE ASSEMBLY

1. Place the new blade assembly into the base frame with the sharp

side up.

2. Reinstall all of the screws, washer plates, and o-rings to loosely

support the blade assembly in the base.

TENSION THE BLADE ASSEMBLY

NOTICE: It is important to perform the following steps in order.

Changing the sequence may damage the equipment.

NOTICE: HAND TIGHTEN ONLY. Do NOT use power tools to tighten

the screws on this equipment. Power tools may damage

the equipment.

Tension the Long Leg Side

1. Use the socket wrench to tighten the screws on the long leg side.

2. Tighten the screws until the assembly is tight against the frame.

WARNING

Sharp Blade Hazard

Blades are sharp and can cut skin. To avoid injury from sharp

blades, wear cut-resistant gloves when using or handling this

product.

• Cut-resistant gloves • Mild dish detergent and warm water

•³⁄₈" socket and socket wrench

• Torque wrench (optional)

500N and 501N:

4 Screws on Each End

502N and 503N:

2 Screws on Each End

www.vollrath.com

The Vollrath Company, L.L.C.

1236 North 18th Street

Sheboygan, WI 53081-3201 U.S.A.

Main Tel: 800.624.2051 or 920.457.4851

Main Fax: 800.752.5620 or 920.459.6573

Customer Service: 800.628.0830

Canada Customer Service: 800.695.8560

Technical Services

[email protected]

Induction Products: 800.825.6036

Countertop Warming Products: 800.354.1970

Toasters: 800-309-2250

All Other Products: 800.628.0832

Tension the Short Leg Side

502N and 503N Slicers

These slicers have two screws on each end that hold the blade

assembly to the frame. To tension the blades, tighten the screws on the

short leg end.

NOTICE: Hand tighten only. Do NOT use power tools. Using power

tools could damage the equipment.

1. Use the socket wrench to tighten the screws as tight as possible.

Notice the corresponding o-rings located between the blade

assembly and the frame. They should be compressed to

approximately ³⁄₃₂" thick. If you have a torque wrench, use it to verify

the screws are tightened to 70 in lbs.

500N and 501N Slicers

These slicers have four screws on each end that hold the blade

assembly to the frame. To tension the blades, tighten the screws on the

short leg end.

NOTICE: Hand tighten only. Do NOT use power tools. Using power

tools could damage the equipment.

1. Use the socket wrench to tighten the screws in a criss cross pattern.

Repeat until all of the screws as tight as possible. If you have a

torque wrench, use it to verify the screws are tightened to 70 in lbs.

Compressed Compressed

³⁄₃₂"

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vollrath Küchengerät Handbücher

Vollrath

Vollrath VPP16 Bedienungsanleitung

Vollrath

Vollrath 47704 Bedienungsanleitung

Vollrath

Vollrath Lettuce King I 400N Bedienungsanleitung

Vollrath

Vollrath 40820 Bedienungsanleitung

Vollrath

Vollrath Medio Service-Handbuch

Vollrath

Vollrath REDCO WEDGEMASTER II Handbuch

Vollrath

Vollrath Lettuce King I 400N Bedienungsanleitung

Vollrath

Vollrath 7217210 Bedienungsanleitung

Vollrath

Vollrath Onion King 500N Bedienungsanleitung

Vollrath

Vollrath SLM250/S Bedienungsanleitung

Vollrath

Vollrath Cheese Blocker 1837 Bedienungsanleitung

Vollrath

Vollrath Mirage 59300 Bedienungsanleitung

Vollrath

Vollrath 40952 Bedienungsanleitung

Vollrath

Vollrath E-Z Leitfaden

Vollrath

Vollrath SLP300/S Bedienungsanleitung

Vollrath

Vollrath Cube King 1811 Bedienungsanleitung

Vollrath

Vollrath 46120 Bedienungsanleitung

Vollrath

Vollrath Redco Instacut 5.0 Bedienungsanleitung

Vollrath

Vollrath Wedgemaster II 700-1 Bedienungsanleitung

Vollrath

Vollrath Lobster King 1851 Bedienungsanleitung

Vollrath

Vollrath SLM330E/S Bedienungsanleitung

Vollrath

Vollrath Onion King 500N Bedienungsanleitung

Vollrath

Vollrath Mirage 59500 Bedienungsanleitung

Vollrath

Vollrath CGA8016 Bedienungsanleitung

Beliebte Küchengerät Handbücher anderer Marken

Tayama

Tayama TYG-35AF Bedienungsanleitung

AEG

AEG 43172V-MN Bedienungsanleitung

REBER

REBER Professional 40 Benutzerhandbuch

North American

North American BB12482G / TR-F-04-B-NCT-1 Bedienungsanleitung

Presto

Presto fountain popper Bedienungsanleitung

Westmark

Westmark 1035 2260 Bedienungsanleitung

Zanussi

Zanussi ZCG64396XA Bedienungsanleitung

HOFFEN

HOFFEN SM-9302M Bedienungsanleitung

Philips

Philips HD3133 Bedienungsanleitung

Ronco

Ronco Beef Jerky Bedienungsanleitung

Hendi

Hendi 470411 Bedienungsanleitung

Livoo

Livoo MEN386 Bedienungsanleitung

croydon

croydon WR-10313-700 Bedienungsanleitung

Chefman

Chefman RJ43-SQ Series Bedienungsanleitung

Vacmaster

Vacmaster VP680 Bedienungsanleitung

Jetmaster

Jetmaster 900HG Bedienungsanleitung

Küppersbusch

Küppersbusch EEH 610.0 Kurzanleitung zur Einrichtung

HURAKAN

HURAKAN HKN-F10 Bedienungsanleitung