Volth S-NET1 Bedienungsanleitung
Networks Cable TesterNetworks Cable Tester
• Power supply for device is 3.7V rechargeable lithium battery.
• Disconnect the 5V 1A Charger when complete charging in fear of danger.
• Please use battery according to the specification; otherwise, it may result in damage to equipment.
• Never put the equipment in the place with much dust, humidity and high temperature (over 40°C).
• Please never dismount the equipment arbitrarily. The maintainance and care shall be conducted by
professional personnel.
• Users can set the auto-off time according to his own needs.
• Please take out the battery in launcher and receiver if the equipment is not used for a long time so
as to prevent that the battery liquid is leaked in future.
• Never use the equipment to detect power cord with electricity (such as power supply circuit of 220V),
otherwise, it may result in damage to equipment and personal injury.
• Never conduct related operation of communication line in thunderstorm weather so as to prevent
lightning stroke and Impact on personal safety.
Overview...........................................................01 Main functions ........................................... ......02
Benefits.............................................................02 Technical Parameters............................... ......02
Product interface and key introduction.........04 Instruction on Main interface................... ......06
Charging function............................................06 Operation steps......................................... ......07
a.Cable line-to-line test......................................09 b.Port flash test........................................... ......12
c.Cable length test.............................................14 d.Cable tracing test..................................... ......21
e.Crosstalk test..................................................24 f.POE test................................................... ......24
g.PING test........................................................25 h.System set............................................... ......26
Power off..........................................................27 Accessories............................................... ......27
Diagram of series products ...........................28
S-NET1 Series are newly developed by our company which are capable of anti current
interference. The equipment is composed of three parts: main tester (S-NET1-M), receiver
(S-NET1-S) and remote identifier (S-NET1-R). It is a multifunction device, capable of measuring
cable length, cable tracing, cable continuity testing, PoE and PING functions also it can detect
voltage presence. Users can read the test results visually from the 3.7 inch color screen. All
these make this item be as a practical tool for low voltage system installation and maintenance
technicians of communication circuits and comprehensive wiring circuits.It is widely used in the
fields like telephone system, computer networks and other metal lead circuits.
Main functions
• PING Testing.
• Detect PoE presence and how much the voltage is.
• Port flash function helps locate the target network cable more easily on the Router / switches
with electricity.
• Scanning cable on the POE Router.
• Capable to test open, short, cross connection, reverse, and broken wire positioning with M-S,
M-R method.
• Measure length of network cable, coaxial cable, telephone cable and USB cable up to
2000m, no connection of remote unit.
• To perform crosstalk test on network cable to solve the potential problem of slow speed.
• To quickly find the targeted cable without stripping isolation among unknown cables.
OK
Pow er
CHG
NCV
SCA N
S E T
R E C E I V E R
Cable Length T ester
WIREMAP
C abl e L ength T es ter
E MI TT E R
Menu
Mapping Port F la sh
POE
Scan
Leng th
Ping
S-NET1
S-NET1
S-NET1
Main tester
(S-NET1)
Receiver
(S-NET1-S)
Remote identifier
(S-NET1-R)
• To trace cable on exchanger or Router without current interference.
• Locate breakage and short position accurately.
Benefits
• Receiver can also be used to detect AC Voltage presence.
• TF function: to import and export data from comupter (160 sets, txt format).
• Rechargable Lithium battery for long-time work.
• Adjustable auto-off time, lamp for work in dark.
Technical parameters
(1). Overall dimensions Main tester : 173X92X34mm.; Receiver : 183X58X35mm.
Remote identifier : 106X32X30mm.
(2). Display 2.8 inch LCD Color screen : 320X240 (Effective visible area 60X45mm).
(3). Power supply 3.7V rechargeable lithium battery1800mAh.
(4). Tracing cable types STP/UTP 5E, 6E network cable, telephone cable, coaxial cable,and
common metal wires connected with alligator clip.
(5). Testing cable types STP/UTP 5E, 6E network cable, telephone cable, coaxial cable, and
common metal wires connected with alligator clip.
(6). Operating environment temperature/humidity -10°C ~ +60°C /20% ~ 70%;
(7). Testing device interface Main unit: RJ45 (M), RJ45 (S), PoE/PING, RJ11, BNC
connector, Remote identifier: RJ45, RJ11, BNC connector interface.
(8). Length measurement Range: 1-2000m; Calibration precision: 2% (+/-0.5m, or +/-1.5
feet); (calibration; cable>10m) measurement precision: 3% (+/-0.5m, or +/-1.5 feet); (AMP,
CAT5E, 6E cable material)Display unit: meter, foot, yard.
(9). Length calibration, storage and data load User can set a length value at a known
length, store the value in the system, which can be used for future choice (9 sets of data
can be stored). and the calibration length should be over 10m.
(10). Cable wiremapping Open, short, reverse , cross, crosstalk, etc.
(11). S-NET1 includes 8 remote units with ID1-ID8.
(12). PoE/PING Testing
(13). Tracing cable Locate targeted cable among lots of cables (only for S-NET1 &
S-NET1W, S-NET1A Can't)
(14). Automatic power-off Users can choose time to turn off the tester automatically.
Ports on Main unit
(1). Three RJ 45 ports on the main unit: One of them is “MAIN” port, used for cable length
measuring and continuity testing. and another one is “SCAN” interface , used for cable
tracing and continuity testing locally; The other one is “PoE/Ping” interface, used for PoE
and PING Testing.
(2). Port RJ11: used for tracing cable, cable length and continuity testing for telephone cable.
(3). Port BNC: used for tracing cable, cable length and continuity testing for coaxial cable.
(4). MICRO: Charging for battery.
(5). TF: Store and export datas (txt format / 160sets can be stored).
Function keys on Main tester
means up/down/ left/right when moving moving cursor to select functions on
Menu. Press “OK” to confirm or start testing. means return to last menu.Press to turn on
or turn off the device.
Function keys on Receiver
is used to detect currency and also for lamp. “SET” can be shifted to two work modes:
cable tracing and AC voltage detecting. Press to adjust the sensitivity. Press to turn
on or turn off the device.
OK
BNC
RJ45
MAIN RJ11
RJ45
SCAN
PoE/Ping
CHG TF Card
C ab le L e n g th T e s te r
E MI TT E R
Menu
Mapping Port Fl as h
POE
Scan
Length
Ping
Main tester
Receiver
S-NET1
Power
CHG
NCV
SCAN
S E T
R E C E IV E R
Cable Length T ester
CHG
S-NET1
Ports on Remote identifier
(1) RJ45: remote testing cable continuity for Lan cable.
(2) Port RJ11: remote testing cable continuity for telephone cable.
(3) Port BNC: remote testing cable continuity for COAX cable. Ports
Instruction on Main interface
Here are seven main functions on Main interface.
(1) Mapping --- Test cable continuity, such as the cable is good, open, short, cross, reverse
connection, etc.
(2) Port flash---locate network cable visually by the flashing port light on Hub / Switch.
(3) Scan--- find the targeted cable among unknown cables, also roughly locate short position
by tone.
(4) PING---to test network performance, data packet, min & max time.
(5) Length--- measure cable length and also display cable errors' distance.
(6) PoE--- identify which pins are providing power and also detect how much voltage
(7) Set---Set up backlight/ backlight time/ auto-off time/ theme color/data export/system
information (version No.),ect.
Charging function
The power supply for main tester and receiver are both 3.7V Rechargeable battery, its
capacity is 1800mAh. When finish charging, the main tester can work continuously for over
20hs, receiver can work for over 50hs. The rechargeable battery avoids the trouble of
replacing 9V battery again and again. The whole standard charging devices are included. After
charging, please disconnect the charging device, otherwise it would shorten the battery life.
WIREMAP
Remote identifier
Menu
Mapping Port Flash
POE
Scan
Length
Ping
Menu
Set
S-NET1
When the emitter low battery(＜3V), it will show “Low battery, auto-off soon! ” ; when
the reciever low battery (＜3V), “power” will flash.
Operation steps
Boot screen Turn on the tester to come to home page.
3 seconds later, the following main interface will be displayed:
Users can set up the systems according to his own needs and to have next operations.
Testing methods
(1) M-S Method--- Checking cable continuity only with main
tester for Lan cable. Connect one end of lan cable into
“Main” port, the other end to “Scan” port. (Graph No.1)
Note: M-S Method is only for Lan cable continuity testing,
not for other kinds of cables.
(2) M-R Methods---Checking cable continuity with main tester
and remote unit, for Lan cable, telephone cable, coax cable.
(Graph No.2)
Note: M-R Methods is for cable continuity testing, not for
cable length measuring.
(3) Scan method---“ RJ45 Scan”“RJ11”“ BNC” ports are used
to trace corresponding cables. (Graph No.3)
(4) Open Method--- Only connect one end of cable into main
tester when measuring cable length, don't connect with
remote or terminator. (Graph No.4)
(5) PoE/ PING Methods--- Connect one end of lan cable with
“POE/Ping” Port, the other end to PoE switcher or router.
(Graph No.5)
S-NET1
Your excellent
helper in cable test! Mapping Port Flash
POE
Scan
Menu
Length
Ping
Set
Menu
1 2 3 4 5 6 7 8 G
M:
S:
1 2 3 4 5 6 7 8 G
RJ4 5 Mapping
Test mo de: Loc al
OK !
Scan
Scanning.. .
1 2 3 4 5 6 7 8 G
M:
R:
1 2 3 4 5 6 7 8 G
RJ4 5 Ma ppi ng
Test mode: R emote
OK !
RJ45 Len gth
1 Open 105 .3m
2 Open 105.3 m
3 Ope n 105.3m
4 Ope n 105. 3m
5 Open 10 5.3 m
6 Ope n 105 .3m
7 Ope n 105 .3m
8 Ope n 105 .3m
Total l ength:
105 .3m
Pin g
Pi ng 1 92 .1 68 .1 .1 w ith 3 2 by te s of d at a:
Re pl y fr om 1 92 .1 68 .1 .1 : t im e= 1m s TT L= 64
Re pl y fr om 1 92 .1 68 .1 . 1: t im e= 1m s TTL=64
Re pl y fr om 1 92 .1 68 .1 . 1: t im e= 1m s TT L= 64
Re pl y fr om 1 92 .1 68 .1 . 1: t im e= 1m s TT L= 64
Pi ng s ta t is ti cs f or 1 92 .1 68 .1 . 1
Pa ck et s : Se nt =4 , Re c ei ve d= 4, L o st =0
Ap pr ox i ma te r ou nd t r ip t im es i n ms :
Mi n= 1m s , M ax =1 ms , A ve r ag e= 1m s
Graph No.1
Graph No.2
Graph No.3
Graph No.4
Graph No.5
a.Cable line-to-line test ( eg: Network cable):
Turn on the device, connect one end of the network cable to “RJ45 Main”, the other end to
“RJ45” port of remote unit. Choose “Mapping” on the main menu, then enter “Cat5” or “Cat6”
to start testing, the testing result will display on the screen directly. If needed, users can also
store the data into TF card.
Test result 1: No connection or the cable doesn't connect well If the cable doesn't connect
to the main tester, or not connect well, the screen will display as below:
At this time, press to return to the main menu, and then press “ENTER” key for re-test.
Test result 2: Short circuit : If there is short circuit with the cable and terminal, it will show as
below: (Short circuit at pin 1 & pin 2)
At this time, press to return to the main menu, and then press “ENTER” key for re-test.
Test result 3: correct connection : If to test a shielded lan cable with remote identifier, and
the cable is good connection, the result is as below graph
R = Short for “Remote idenfifier” M= Short for “Main tester”
G= Short for “Ground”,the shield layer for STP cable S = Short for “RJ45 Scan”
If you press it means back to the last menu and press OK means test again or back to
the main menu for re-test.
Test result 4: open circuit (Local testing with Main tester) When local test and meet open
circuit, it will show as below:
Data upload
Start
Testing...
Mapping
RJ11 BNC
CAT5 CAT6
CAT5 Mapping CAT5 Mapping
Mapping Port Flash
POE
Scan
Menu
Length
Ping
Cable open or too short!
CAT5 Mapping
x x 3 4 5 6 7 8 G
M:
R:
X X3 4 5 6 7 8 G
Wire Map:
CAT5 Mapping
Short mapping: 12
1 2 3 4 5 6 7 8 G
M:
R:
1 2 3 4 5 6 7 8 G
CAT5 Mapping
Test mode: Remote
OK !
In the figure, “X” shown in “3” position, indicates there is open circuit. Note: Because network
cable is made of pair cores, if there is open circuit, it will show faults in pairs, just as above "4"
&" 5". it means either "4" pin or "5" pin exists an open circuit, or both "4" and "5" exist an open
circuit.
Test result 5: open circuit (Remote testing with Remote unit)
In the figure, “X” shown in “4” and “5” pin position, indicates there is open circuit in “4” and “5”
pin of the remote pin. Note: (NF-8601W) Because network cable is twisted pair cables, if there
is open circuit, it will show faults in pairs, just as above "4" &" 5". it means either "4" pin or "5"
pin exists an open circuit, or both "4" and "5" exist an open circuit.
Test result 6: Cross (out of order ) When the cables have cross situation , it will show you
as below :
Test result 7: Short , Open , Cross If the cable exsits short , open and cross together, will
show you this result : ( 1 and 2 is short , 4 and 5 open , 7 and 8 was cross ):
Test result 8: Continuity test for CAT6 It's the same result with Network cable test ,it will
show as below:
Test result 9: Continuity test for 6 pin telephone cable The 6-core telephone cable should
insert into the RJ11 interface and the test method and show result is the similar with network
cable.
1 2 X 4 5 6 7 8 G
M:
S:
1 2 X 4 5 6 7 8 G
Open mapping: 3
Test mode:Local
CAT5 Mapping
1 2 3 X X 6 7 8 G
M:
R:
1 2 3 X X 6 7 8 G
CAT5 Mapping
Open mapping: 45
Test mode: Remote
1 2 3 4 5 6 7 8 G
M:
R:
1 2 3 4 5 6 7 8 G
CAT5 Mapping
Test mode: Remote
Cross mapping: 78
X X 3 X X 6 7 8 G
M:
R:
X X 3 X X 6 7 8 G
CAT5 Mapping
Test mode: Remote
Short mapping: 12
Cross mapping: 78
Open mapping:45
Data upload
Start
Testing...
CAT6 Mapping CAT6 Mapping
BNC
Mapping
RJ11
CAT5 CAT6
Mapping Port Flash
POE
Scan
Menu
Length
Ping
Test result 10: Continuity test for coax cable When you test the coax cable , you should
insert into the BNC interface and the test method is the similar with network cable.
Attention: The cable continuity testing is only for more than 2-core cables , it's useless for
single cable.
b. Port flash testing: (only for good network cable scanning)
After entering main menu, choose “port flash” function, it will show on the screen. Insert
one end of the lan cable into “POE/PING” Port, the other end connects to the switch, then the
hollow circle will turn into , besides, on the other side, the switch port which the targeted
cable connects to will flash in a different frequency as other ports. It helps users to find the
target cable on switch much easier and visually. The image is as below:
Special Use: network detection The device can test line sequence under the
switches work on. Network cable as the example---One side connect the main tester's RJ45
MAIN interface and the other side connect the switch , then you can press the test button
directly , if the connection is right , will show you as below ( when the switch is 8 cores )
This is the especial test result display when check cable wiremapping connected to switcher.
Since the switcher is shorted itself, that's why the result is short mapping, but it still means the
cable is good.
But if the Pin1 & Pin2 of the tested switch was open , the testing result will display as below.
(when the switch is 8 cores).
Data upload
Start
Testing...
RJ11 Mapping RJ11 Mapping
BNC
Mapping
CAT5 CAT6
RJ11
Mapping Port Flash
POE
Scan
Menu
Length
Ping
Data upload
Start
Testing...
BNC Mapping BNC Mapping
Mapping
CAT5 CAT6
RJ11 BNC
Mapping Port Flash
POE
Scan
Menu
Length
Ping
Mappi ng Port Flash
POE
Scan
Menu
Lengt h
Ping
Port Flash Port Flash
X X XX X X X X
M:
R:
X X X X X X X X
CAT5 Mapping
Test mode: Remote
Short mapping: 12345678
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Beliebte Kabeltester Handbücher anderer Marken
Radiodetection
Radiodetection RD8100 Bedienungsanleitung
Vonaq
Vonaq EasyCheck 900 Bedienungsanleitung
Softing
Softing CableMaster CM200 Bedienungsanleitung
Microtest
Microtest 8751 Bedienungsanleitung
Psiber Data Systems
Psiber Data Systems 20 Bedienungsanleitung
Platinum Tools
Platinum Tools LANSeeker TP500C Bedienungsanleitung
