Vortex FURY HD 5000 Bedienungsanleitung

PRODUCT MANUAL

LASER RANGEFINDING BINOCULARS

FURY®HD 5000

2 3

FURY®HD 5000

Ocular Lens

Center Focus

Twist-up Eyecup

Strap

Attachment

Reticle Focus Diopter Focus

Measure Button

Menu Button

Tripod Adapter Socket

Objective Lens

FURY®HD 5000 LASER RANGEFINDING BINOCULAR

The Fury®HD 5000 is an extremely effective angle-compensated

laser rangeﬁnding binocular intended for hunters, archers and

shooters. The primary HCD (Horizontal Component Distance)

mode provides key angle compensated range information required

by the vast majority of riﬂe and bow shooters in a simple,

quick-to-read display.

The Fury®HD 5000 also has a LOS (Line of Sight) mode and Scan

feature, along with adjustments for reading in yards or meters and

setting the brightness of the display.

Images are for representation only. Product may vary slightly from

what is shown.

4 5

FURY®HD 5000

BASIC OPERATION

Adjust the Eyecups

The eyecups on a Fury®HD 5000

twist up and down so any viewer can

see the full ﬁeld and enjoy

comfortable viewing—with or

without eyeglasses.

When not using eyeglasses or

sunglasses, keep the eyecups

fully extended. For best viewing

when wearing eyeglasses, twist

eyecups down.

Adjust the Interpupillary Distance

The interpupillary distance (IPD) is the distance between the

centers of the left and right eye pupils. Match the IPD of your eyes

to that of the binocular so you see a single image free of shading.

Rotate the binocular barrels inward or outward to line your eyes up

with ocular lenses.

–

Install Battery

Open the battery compartment and

install the CR2 battery included with

the Fury® HD 5000.

Install battery with

positive side facing in.

Power Up

To power up the Fury®HD 5000 and

prepare for ranging, press and release

the Measure button. The HCD or LOS

ranging screen will display. The Fury®

will power down automatically after

ten seconds of non-use.

Low Battery Icon

The low battery icon comes on at 25%

and stays on until there is no power.

6 7

FURY®HD 5000

Mode Selection Display

Menu Button

Measure Button

Properly Focus the Rangeﬁnding

Display and Binocular

For the best views, follow this process to

properly set the display, center focus, and

diopter. Choose an object that is about

20 yards away from you and stay in the

same spot until you have adjusted the

binocular for your eyes.

1. Power up the binocular and close your

left eye.

2. While viewing the rangeﬁnding display

with your right eye, focus your right

eye on the object and adjust the

center focus wheel until the object is

in focus. Leave the center focus wheel

in this position.

3. Then, using the reticle focus

adjustment ring, adjust the reticle

focus to bring the display into sharp

focus. Once this is done, you will

not have to refocus the rangeﬁnding

display again.

4. Close your right eye or cover the right

objective lens with your hand. Looking

at the object with your left eye, adjust

the diopter so the object is in focus.

Make note of this diopter setting in

case you need to set it again. From

this point on, you will only need to use

the center focus wheel.

Adjust Reticle Focus Ring

Mode Selection

Your Fury® HD 5000 is factory set to the angle compensating

HCD ranging mode, best target mode, yards, and maximum

brightness. For most users, these are the preferred settings.

To change modes: Press and release the Measure button to

power on and then press and hold the Menu button for at least

four seconds. Once the Mode Selection screen displays, release

the button.

As you progress through Mode Selection, you may exit at any

time and save your settings by pressing and holding the Menu

button for at least four seconds—the Fury®will return to

power-up condition.

8 9

FURY®HD 5000

SET AND SAVE MODE SELECTIONS

Ranging Mode Selection

Choose Between the HCD and LOS Modes.

After activating the Mode Selection, press the Measure button

to toggle between the HCD and LOS displays. Press the Menu

button to save your desired choice and move to the Yards/Meters

selection screen.

Display Selection

Choose Between Yards and Meters Display.

Press the Measure button to toggle between the Yards and Meters

display. Press the Menu button to save your desired choice and

move to the Brightness selection screen.

Brightness Selection

Choose Between Five Brightness Settings.

The Fury® HD 5000 provides ﬁve

illumination settings. Press the Measure

button to toggle through the ﬁve Brightness

settings. Press the Menu button to save

your desired setting and move back to the

target mode selection.

Target Mode Selection

Target Mode Explanations

The Fury®HD 5000 provides two target modes: Best Mode and

Last Mode.

Best Mode

Your Fury®HD 5000 comes preset to Best target mode. This is

the standard mode providing the range of the target with the

strongest range result. Best Mode is the recommended target

mode for most situations.

Last Mode

Displays the farthest distance when panning and scanning. This

mode is ideal for ranging a speciﬁc target behind a group of objects

like brush, trees, rocks, etc.

10 11

FURY®HD 5000

Scan Ranging

Activate Scan Ranging by pressing and holding the Measure

button down. Keeping the button depressed will continuously

measure distance as you pan back and forth across target objects.

The aiming circle will blink as you pan. Releasing the Measure

button will return laser to the Power Up Condition.

HCD Scan LOS Scan

No Range

Returned

Setting Target Modes

Press the Measure button to toggle between the Best and Last

displays. Press the Menu button to save your desired choice and

move back to the HCD/LOS selection screen.

To exit Mode Selection and save settings, press and hold the Menu

button for four seconds. Settings will also save when Fury®powers

down automatically.

Ranging

With the Fury® HD 5000 powered up,

position the reticle on the target object

and press and release the Measure button

to get the distance measurement. If

the laser is not able to range due to the

reﬂectivity of the target, you will see a

display similar to that shown here. To

range a new target, simply re-aim and

press the Measure button again.

12 13

FURY®HD 5000

Ranging Mode Explanations

The Fury® HD 5000 provides two range modes: HCD (Horizontal

Component Distance) and LOS (Line of Sight). Both modes offer

a Scan feature.

HCD Mode

The HCD range display is intended to be the primary mode—used

for most riﬂe and archery shooting applications. The yardage

number displayed is the critical horizontal component distance.

Horizontal Component

Distance: 385 Yards

500 Yard Line of Sight

Using the HCD Mode

Use the HCD range mode in the following situations:

• Riﬂe shooting on level ground at any range.

• Riﬂe shooting out to ranges of 800 yards with mild slopes (less

than 15°).

• Riﬂe shooting out to ranges of 400 yards with moderate slopes

(15° to 30°).

• For all archery shooting.

The displayed HCD yardage number is corrected for shot angle

and needs no extra user input; shooters simply use the appropriate

level ground bullet drop and wind adjustment for the range

displayed and shoot. Archers use the appropriate level ground

sight pin for the range displayed and shoot.

LOS Range

Incline angle

14 15

FURY®HD 5000

LOS Mode

The LOS (Line of Sight) mode is intended for riﬂe shooters who are

using slope correcting ballistic drop data cards, ballistic cell phone

applications, or other devices with ballistic programs and who are

shooting at distances beyond 500 yards and with slopes greater

than 15°. Most shooters and archers will not need the LOS mode.

The range number displayed in LOS mode is the actual line of

sight range with no ballistic correction for slope. Most of the

commonly used ballistic devices can provide independent slope

correction for bullet drop data and require actual line of sight

range input. Using the LOS range when calculating bullet wind

drifts under these steep slope/long range conditions will provide a

higher degree of accuracy than using the HCD range.

To use, simply input the LOS range number into the electronic

device or use the LOS range when referencing ballistic drop cards

with slope correction.

LOS Mode - Incline

When in LOS mode, an additional number is displayed above the

yardage number. This number is slope incline shown in degrees.

The slope incline number

can be entered into ballistic

programs or ﬁeld cards to help

calculate precise bullet drops

in mountainous terrain.

Scan Feature

The Scan feature can be used to range moving targets or help

range smaller targets on uniform backgrounds, and works in both

ranging and target modes. Once powered up, press and hold the

Measure button and scan back and forth, watching for changes

in the yardage number as the aiming circle moves across target

objects. The illuminated “Scan” icon display indicates Scan

Ranging is activated.

Tripod Use for Ranging

Using a tripod to steady the Fury® HD 5000 will greatly increase

your ability to range small targets at longer distances. To use on a

tripod, you will need to use a binocular tripod adapter. The reticle

may appear tilted depending on tripod level.

16 17

FURY®HD 5000

Rangeﬁnding Tips

Rangeﬁnding binoculars work by emitting a brief pulse of light aimed

at a target object. Distance is determined by the amount of time

taken for the light to emit and return to the laser’s internal receiver.

A laser’s ability to read range can be affected by many things—

mostly relating to the target objects.

• Light colors will usually reﬂect better than dark ones.

• Be aware that snow, rain, and fog will have adverse effects on

ranging ability.

• Shiny, reﬂective surfaces will usually reﬂect better than

dull, textured surfaces. Animal hair will not reﬂect as well

as a hard surface.

• Ranging under cloud cover can improve laser performance

compared to bright sunny conditions.

• Solid objects, such as a rock, will reﬂect better than bushes.

• Flat surfaces perpendicular to the laser pulse will reﬂect

better than curved surfaces or surfaces angled in relation to

laser pulse.

• Ranging over water can sometimes cause false reﬂections

and readings.

• At longer distances, large objects will be easier to range

than small objects.

• If you are having difﬁculty ranging an animal or object, try ranging

a different nearby object, or use the Scan feature to pan back and

forth while watching for changes in range number.

ACCESSORIES

Carry Case

The protective case provides safe storage between viewing

sessions. The carry strap is already attached to the case.

Lens Covers

A rainguard for the ocular lenses and tethered objective lens

covers is included. Use these covers to protect the lenses

whenever you are not viewing.

Neckstrap

Attach the padded neckstrap in three simple steps.

NOTE: If using another type of strap, never attach metal o-rings

directly onto the strap attachment.

1. Push a few inches of

the strap through the

strap attachment on

the binocular.

2. Hold the buckle and

thread the end of

the strap through

the buckle.

3. Adjust the overall

length, then pull tight

until strap is secured

within the buckle.

18 19

FURY®HD 5000

Lens Care

Maintain the optical brilliance of your binocular by keeping lens

surfaces free of dirt, oils, and dust.

Protect Lenses While Out in the Field

Make use of the provided eyepiece and tethered objective lens

covers to protect the lenses when not viewing. If the optics are

exposed to moisture, keep the caps off and allow the optics to dry

out completely before putting them in the case for storage.

Keep Lenses Clean

In order to enjoy the

best views through your

binocular, take time to

regularly clean the

exterior lenses:

1. Remove any dust or

grit from lenses before

wiping. Use a can of

pressurized air, soft

camel hair brush,

or an acrylic

optical brush.

2. Clear lenses of smudges, ﬁngerprints, or eyelash oil. Fog the

lenses with your own breath, then use a non-abrasive lens

cloth to clean the lenses.

NOTE: Use lens cleaning ﬂuid and optical paper to clean lenses.

Never use facial tissue, heavy cotton, or ﬂannel clothing on

lenses—these materials can scratch the surface of a lens.

CAUTION: Binoculars are not intended for looking at the sun, or any

other intense light source. Such viewing could damage the retina

and cornea of your eyes—even to the point of causing blindness.

Andere Handbücher für FURY HD 5000

Inhaltsverzeichnis

Andere Vortex Fernglas Handbücher

Vortex

Vortex Vulture HD Bedienungsanleitung

Vortex

Vortex Viper 10x32 Bedienungsanleitung

Vortex

Vortex VULTURE HD Bedienungsanleitung

Vortex

Vortex Viper 8x28 R/T Bedienungsanleitung

Vortex

Vortex FURY HD 5000 Bedienungsanleitung

Vortex

Vortex Viper HD Bedienungsanleitung

Vortex

Vortex BIN-DBK-12A Montageanleitung

Vortex

Vortex Viper Series Bedienungsanleitung

Vortex

Vortex Kaibab HD Bedienungsanleitung

Vortex

Vortex Razor HD Bedienungsanleitung

Vortex

Vortex Viper Bedienungsanleitung

Vortex

Vortex SOLO R Bedienungsanleitung

Vortex

Vortex Diamondback HD Bedienungsanleitung

Vortex

Vortex TRIUMPH HD Bedienungsanleitung

Vortex

Vortex FURY Bedienungsanleitung

Vortex

Vortex Diamondback 10x28 Bedienungsanleitung

Vortex

Vortex FURY HD 5000 AB Bedienungsanleitung

Vortex

Vortex DB-205 Bedienungsanleitung

Vortex

Vortex VIPER HD Bedienungsanleitung

Vortex

Vortex Vulture 10x56 Bedienungsanleitung

Vortex

Vortex Raptor 6.5x32 Bedienungsanleitung

Vortex

Vortex FURY HD 5000 AB Bedienungsanleitung

Vortex

Vortex DiamondBack Bedienungsanleitung

Vortex

Vortex Vanquish Bedienungsanleitung

Beliebte Fernglas Handbücher anderer Marken

Celestron

Celestron VistaPix 72218 Bedienungsanleitung

Levenhuk

Levenhuk Atom Digital DNM200 Bedienungsanleitung

ATN

ATN PS-15 Bedienungsanleitung

Bresser

Bresser TOPAS 7x50 Bedienungsanleitung

Berger & Schroter

Berger & Schroter LN-G3-B50 Bedienungsanleitung

Leica

Leica geovid 8x42 HD-R Bedienungsanleitung

Noblex

Noblex NF 8 x 42 inception Bedienungsanleitung

Newcon Optik

Newcon Optik AN Series Bedienungsanleitung

PHOTONIS

PHOTONIS VYPER Bedienungsanleitung

ATN

ATN 6015-WPT Bedienungsanleitung

Famous Trails

Famous Trails ViewCatcher DCB 822 Bedienungsanleitung

AGM

AGM EXPLORATOR FSB50-640 Bedienungsanleitung

Opticron

Opticron Marine-3 7x50 BIF.GA Installationsanleitung

Kayoba

Kayoba 009129 Bedienungsanleitung

Vixen

Vixen ARENA Series Bedienungsanleitung

MAGINON

MAGINON NVB 60 Bedienungsanleitung

Leica

Leica Geovid 56 Bedienungsanleitung

Leica

Leica GEOVID PRO Bedienungsanleitung