Voxx Electronics Prestige APSRS1Z Bedienungsanleitung

128-9479

1 of 4

Model APSRS1Z

Owner’s Manual

PATENTED: www.voxxintl.com/company/patents

PRESTIGE

KEYLESS ENTRY

The button on the transmitter can be used to unlock the vehicle's doors, while

running under control of the remote start. Simply press and hold transmitter button

for 3 seconds as you approach the vehicle and the doors will unlock.

NOTE: Vehicle must have power door locks, and this option must be connected

at time of installation.

REMOTE CAR FINDER

The Start button is also used to access the car nder mode. This

feature is particularly useful in a crowded parking lot where nding

your car may be difcult. To access the car nder mode, while

within range of your car, simply press and hold the button of your

transmitter for three seconds. The parking lights will begin to ash

making your vehicle more visible. The lights will stop automatically

after 30 seconds. If you wish to turn off the car nder mode prior

to the expiration of the 30 second timer, press and release button

of your transmitter one time.

1 Channel Remote Car Starter

FEATURES

2 One Button Programmable RF Transmitters

One Channel Receiver (capable of accepting 4 transmitters)

External Superheterodyne Receiver Antenna w/Push Button Switch & LED

PBS / (-) Unlock Output

On-Board Start Relay

On-Board Accessory Relay

On-Board Ignition 1 Relay

On-Board Ignition 2 Relay

Ignition 2 Relay Selectable On or Off During Cranking

On-Board Parking Light Relay

Ignition 3 / Shock By-Pass / GM VAT Output (relay required)

Tach Signal Learning Circuit

( + ) and ( - ) Safety Shutdown Circuits

Alarm By-Pass Output

Accessory Outputs

(Pulse Before & After Start, During Crank & After Shut Down)

Selectable Steady or Flashing Parking Lights for Run Indication

Selectable 5, 10, 15, 20, 45 & 60 Minute Run Time

Selectable 1 Sec., 3.5 Sec., or 1 Sec./Dbl 1 Sec. Door Lock Output Pulse

Car Finder Mode

128-9479

2 of 4

REMOTE STARTING THE VEHICLE

This unit will not start the vehicle if any one of the following situations exist:

 The vehicle's hood lid is opened.

 The gear shift selector is not in Park.

 The brake pedal is depressed.

 The safety control switch is in the Off position.

1. To start the vehicle, press and release the Start button two times within

2 seconds. The vehicle will start and remain running for the pre-programmed

run cycle of up to 60 minutes. As a visual indication, the parking lights will ash

or remain on depending on the setting by your installation center.

2. When you arrive at the vehicle, turn the ignition key to the ON position (not the

spring loaded start position), then step on the brake pedal to disengage the

remote starter. The vehicle will continue to run, but now on its own power.

NOTE: The engine will stop running before the pre-programmed run cycle has

expired if you perform any one of the following functions:

- Press and release Key/Trunk button on the keychain transmitter two

times within 2 seconds

- Depress the brake pedal

- Open the vehicle's hood

- Place the unit in the safety override/disabled mode

PUSH BUTTON LED RECEIVER VALET/OVERRIDE/SAFETY CONTROL

SWITCH

The Push Button LED switch located in the receiver allows you to temporarily

disable the remote starting function of the system. This is recommended whenever

the vehicle is being serviced.

To place the system in the service mode:

1. With the system disarmed/unlocked, and the ignition switch off, Press and

Hold the Push Button, found on the windsheild receiver, in.

2. Turn the ignition switch on, off, on, off, on, off.

3. The LED begins to ash two short ashes followed by one long ash and

continues this pattern until returned to normal mode of operation.

This puts the unit into the R/S Override mode indicating that the remote start

is in the service mode and will not start from RF or any other input Posse or

otherwise.

To Exit R/S Override Mode:

1. With the system disarmed, Press and Hold the Push Button, found on the

windsheild receiver, in.

2. Turn the ignition switch on, off, on, off, on, off.

3. The LED turns off, indicating that the R/S unit is fully functional once again.

NOTE: The LED on the receiver can be selected/toggled on and off. This feature

is useful if you do not want the LED ashing all the while the vehicle is locked.

To toggle this feature on or off:

1) Turn the ignition switch on then off.

2) Within 5 seconds, Press and hold the receiver's push-button switch for

128-9479

3 of 4

5 seconds. The LED will ash once for "ON" and twice for "OFF". On, means

normal ash patterns will function, and off normal ash patterns will not function.

The Programmed Transmitter Notication, will always function, as well, or the

programming mode of the unit for transmitters or feature selection.

PROGRAMMED TRANSMITTER NOTIFICATION (PTN)

Every time after Disarm, when the ignition key is turned on, the unit's LED will

report the number of transmitters programmed into the system. This safety

feature will alert you if an unauthorized transmitter has been programmed

into your vehicle's security system without your knowledge. Typically from the

factory, there will be 2 ashes and a pause, repeated 3 times, indicating that

two transmitters are programmed into the system. If you note additional ashes,

an additional transmitter may have been added without your knowledge or

authorization. If you notice a change in the transmitter LED report pattern, you

can correct this by looking up how to erase and reprogram your transmitters

found in the transmitter programming guide. This reprogram operation will erase

all unauthorized or unwanted transmitters.

PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS (BANK 1)

The Transmitter Model Name 171BP, is also found on the back of the transmitter

case. This transmitter uses a CR2032 Battery.

1. Turn the ignition key to the on position.

2. Press and Release the valet/programming switch 3 times

(Siren Chirps and lights ash).

3. Press the Button of each transmitter you want programmed until you hear a chirp

from the horn or siren, or the parking lights ash.

4. Turn the ignition switch off.

The above action programs the Start button in a 1 button system.

Transmitter Battery Replacement:

1. Locate the slot along side lower right side of the transmitter case and using a

plastic tool or a coin, separate the two transmitter case halves.

2. Slide the CR 2032 battery from the battery holder paying attention to the battery

orientation's (+) side facing away from the circuit board.

3. Replace the battery with a new one.

4. Reassemble the case in reverse order of disassembly.

128-9479

4 of 4

PATENTED: www.voxxintl.com/company/patents

To purchase replacement transmitters or to get additional product

information go to: www.prestigecarsecurity.com

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran-

tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Warning!

Changes or modications made to this equipment not expressly approved by the part responsible for compliance could

void the use’s authority to operate the equipment

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this

equipment. Such modications could void the user’s authority to operate the equipment.

FUNCTION SETTING CHART

To be completed by installer

Run Time _______Min 

Door Lock Timer _______Sec 

Parking Lights Pulse Steady 

WARNING!

A running vehicle produces dangerous carbon monoxide gas which can

be fatal if prolonged exposure occurs. Be certain the vehicle is outdoors

before activating the remote start function.

Inhaltsverzeichnis

Andere Voxx Electronics Fernstartsystem Handbücher

Voxx Electronics

Voxx Electronics Prestige PE1BZ Bedienungsanleitung

Voxx Electronics

Voxx Electronics SRT-9000 Bedienungsanleitung

Voxx Electronics

Voxx Electronics PRESTIGE APSSECRS Bedienungsanleitung

Voxx Electronics

Voxx Electronics Pursuit PRO9056Z Installations- und Betriebsanleitung

Voxx Electronics

Voxx Electronics Code Alarm ELITE ca1155E Bedienungsanleitung

Voxx Electronics

Voxx Electronics Elite Series Bedienungsanleitung

Voxx Electronics

Voxx Electronics Prestige APS997ZLR Bedienungsanleitung

Voxx Electronics

Voxx Electronics CA-510 Bedienungsanleitung

Voxx Electronics

Voxx Electronics Pursuit PRO9556Z Bedienungsanleitung

Voxx Electronics

Voxx Electronics PRESTIGE APS787Z Bedienungsanleitung

Voxx Electronics

Voxx Electronics Prestige PE1BTWZ Bedienungsanleitung

Voxx Electronics

Voxx Electronics CA-420 Bedienungsanleitung

Voxx Electronics

Voxx Electronics Prestige PE1BTWZ Bedienungsanleitung

Voxx Electronics

Voxx Electronics Prestige APS901TM Bedienungsanleitung

Voxx Electronics

Voxx Electronics PURSUIT PROSEC Bedienungsanleitung

Voxx Electronics

Voxx Electronics Prestige PE2LCD Bedienungsanleitung

Voxx Electronics

Voxx Electronics Prestige APS510Z Installations- und Betriebsanleitung

Voxx Electronics

Voxx Electronics PURSUIT PR1BTWZ Bedienungsanleitung

Voxx Electronics

Voxx Electronics PRESTIGE APS901Z Bedienungsanleitung

Voxx Electronics

Voxx Electronics Code Alarm Professional Series ca6155 Bedienungsanleitung

Voxx Electronics

Voxx Electronics PurSuit PRO9776Z Bedienungsanleitung

Voxx Electronics

Voxx Electronics Prestige APS997Z Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch

Rooboost

Rooboost RB-1750WP Bedienungsanleitung

Schumacher

Schumacher INSTANT POWER IP-75C Bedienungsanleitung