VQ mitsubishi A6M5 ZERO Bedienungsanleitung
RADIO CONTROL MODEL
Semi Scale – Almost ready to fly
MITSUBISHI A6M5
ZERO
ASSEMBLY INSTRUCTION
.40 - .46 CLASS – 2 CYCLE ENGINE
.60 - .70 CLASS – 4 CYCLE ENGINE
WARNING: This radio control model is not a toy. If modify or
flown carelessly, it could go out of control and cause serious
bodily injury or property damage, It is your responsibility to
build this kit correctly, to properly install all components and to
seek the help of an experienced R/C pilot for a pre-flight sa
inspection and flight test.
fety
Silicon tube
Extension for aileron
servo
For 40 ~ 46 ( 2 cycle engine) For 60 ~ 70 (4 cycle engine)
10.5x6 ~ 11x6 12x6 ~ 13x7
Minimum 4 channel radio for
airplane (with 4 standard servos)
5th channel for retract (with retract
servo
)
40 ~ 46 2 cycle
60 ~ 70 4 cycle
(Purchase separately)
Linkage Stopper
REQUIRED FOR OPERATION (Purchase separately)
CA
Cut away only the film
Cut away only
the film
Using the aileron servo tray as a template,
trace around the outside edge of the aileron
servo tray and then remove it.
Using a sharp hobby knife, cut away the
covering inside the lines. Not to cut into the
wood.
Apply the aileron servo tray in place and
secure the servo tray with CA glue.
Aileron servo tray (Ply wood)
2- Aileron servo tray
X
X
Included with the radio set.
Aileron servo
Retract landing gear
servo
1.2mm
3- Servos installation
AB
L/R
AB
! Make sure to glue
securely, If not properly
glued, a failure in flight may
occur.
Trial fit each part before gluing . Be certain
that there are no gaps. If the parts will join,
but with a gaps, sand or trim the parts a little
at a time until the parts meet exactly with no
gaps.
Check for the correct dihedral angle
Carefully slide the wing halves together, ensuring that they are accurately aligned, Firmly press the two
halves together, allowing the excess epoxy run out. Using rubbing alcohol and paper towel, clean off
the excess epoxy.
When joining the wing halves it is extremely important to use plenty of epoxy (30 minutes epoxy).
1- Joining the wing
Use epoxy glue to bury the opening
RETRACTED
EXTENDED
Left
Right
Push rod
Retract servo
Aileron servo
20 - 28mm
Push rod
Wheel
Wheel Gear cover Retract gear
Retract gear
4- Retract landing gear Installation
Wing Top-view
Retract Push rod
170 mm
40mm
8mm
30mm
10mm
RIGHT RETRACT PUSHROD
30mm
10mm
120mm
40mm
8mm
LEFT RETRACT PUSHROD
To retract servo
To retract servo
To landing gear
To landing gear
1.5mm
AB
!
CA L/R Assemble left and right
sides the same way. X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
Ply gear mount plate Square plastic
Main gear (left)
Main gear (right)
Gear mount
(hard wood)
Plastic strap
3x10mm screw..16
Plastic strap
Main gear
Gear mount
(hard wood)
Ply gear mount
plate
Square plastic Apply Epoxy glue
(Or use 3x10 screw)
5- Main Wing: Fix gear
CA
L/R
Fitting strap
Fix main gear
ABS Gear cover
Collar
Stopper
6- Main Wing: Landing gear
7- Main Wing: Fix gear
3mm screw
Wheel well cover (for fix gear)
Gear cover
CA
L/R
L/R
!
AB
A
A=107 ~ 110mm
IN CASE OF 4CYCLE ENGINE
!
2.5mm
3.1mm
4mm
! Engine thrust on balk head
is already adjust at factory
3x20mm screw
4x25mm screw
Washer.............4
Nut..............4
................4
..............4
SIDE VIEW
FRONT VIEW
! Before installing the engine mounts,
place the engine onto the mounts
and make four 3.1mm holes
8- Engine: Four-stroke engine
A= 116 ~ 119mm
IN CASE OF 2 CYCLE ENGINE
FRONT VIEW
TOP VIEW
Determine the angle for the engine mounts so
the muffler will not contact the fuselage or use
silencer extension adaptor
!
!
9- Engine: Two-stroke engine
X
3x30mm screw
4mm
10- Fuel tank
2x10mm screw
2x10mm screw
............3
3x20mm screw
............4
3x20mm screw
2mm
11- Cowling
Cut away only
the film both
side
Cut away only
the film both side
CA
AB
90O90O
AA’
! Securely glue together
If coming off during fly,
you lose control of your
air plane.
12- Vertical/Horizontal Tail
CA
3mm screw
13- Tail cover
1.5mm
AB
!
CA L/R Assemble left and right
sides the same way. X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
Connector
........ 3
........ 1
Connector
X
Elevator pushrod
3mm set Screw
2 mm
Elevator pushrod
ELEVATOR SERVO
X
Rudder pushrod
3mm set Screw
2 mm
THROTTLE / RUDDER SERVO
(Or throttle pushrod)
Rudder push rod
Rudder servo
Elevator push rod
Throttle push rod
Elevator servo
Throttle push rod
14-Servo/Push rod
CA
Instrument panel
sticker
Do not use to much CA glue or it will make
the canopy glue
!
15- Canopy
107 mm
Wing center section
DO NOT try to fly an out-of-balance model !
16- Balance
35 mm
35 mm
6mm
6mm
10mm
10mm
RUDDER STROKE ELEVATOR STROKE
AILERON STROKE
17- Control Surface
Inhaltsverzeichnis
Andere VQ Spielzeug Handbücher
VQ
VQ KAWASAKI Ki-61 Hien "Tony" Bedienungsanleitung
VQ
VQ P-38 LIGHTNING Bedienungsanleitung
VQ
VQ VQA05 Tuskegee Bedienungsanleitung
VQ
VQ Airacobra P-39 Bedienungsanleitung
VQ
VQ Wasp Bedienungsanleitung
VQ
VQ F8F RareBear Bedienungsanleitung
VQ
VQ P-51D MUSTANG Bedienungsanleitung
VQ
VQ VQA053 Bedienungsanleitung
VQ
VQ CESSNA 208 Bedienungsanleitung
VQ
VQ FLY BABY BIG Bedienungsanleitung
VQ
VQ VQA142DC Bedienungsanleitung
VQ
VQ VQAA040G Handbuch
VQ
VQ Mega Fly Bedienungsanleitung
VQ
VQ WASP Bedienungsanleitung
VQ
VQ FOCKE-WULF FOCKE-WULF Bedienungsanleitung
VQ
VQ KA-3 Bedienungsanleitung
VQ
VQ T-34 Mentor Betriebsanleitung
VQ
VQ hurricane Bedienungsanleitung
VQ
VQ VQA120 Bedienungsanleitung
VQ
VQ 141A08 Bedienungsanleitung
