VWR SAS Super IAQ Bedienungsanleitung

VWR® Microbiological Air Sampler

SAS Super IAQ

INSTRUCTION MANUAL

European catalogue numbers:

710-0868 710-0919

Version: 1

Issued: February 2020

Legal address of manufacturer

Europe

VWR International Srl

Via S. Giusto 85

20153 Milano

Italy

Tel.: + 39 02-3320311

http://it.vwr.com

Country of origin: Italy

Table of contents

Legal address of manufacturer ................................................................................................ 2

Warning ..................................................................................................................................... 4

Safety information .................................................................................................................... 4

Kit and unit description ............................................................................................................ 5

Technical features ..................................................................................................................... 6

Intended use .............................................................................................................................. 6

Brief operating instructions ..................................................................................................... 7

Installation ................................................................................................................................. 7

Functions ................................................................................................................................... 9

Colony Forming Unit correction factor .................................................................................. 15

Accessories ............................................................................................................................. 18

Troubleshooting ...................................................................................................................... 19

Technical service .................................................................................................................... 20

Warranty .................................................................................................................................. 20

Compliance with local laws and regulations ......................................................................... 20

Equipment disposal ................................................................................................................ 21

Warning

This document is the property of VWR International S.r.l. - Milan - Italy

It may not be duplicated or distributed without the owner’s authorisation.

Patent pending

Manufactured by VWR International S.r.l. - Milan, Italy

Safety information

Use the device only for the indicated purposes.

The device must be correctly used according to this instruction manual before starting any operation.

Immediately replace any electrical cable when damaged.

Always disconnect the charger before:

 Repairing or maintenance; these operations must be carried out by qualified staff

 Cleaning the unit

Use original spare parts and accessories for any replacement.

Do not use this device in the presence of explosive gas.

Please follow the guidelines below and read this manual in its entirety to ensure safe operation of the unit.

Be aware that the voltage and frequency of the electrical system are compatible with the electrical

requirements of the battery charger.

Never use a non OEM charger to charge the air sampler.

Use of improper charger may damage the unit.

ENGLISH

Kit and unit description

1. Soft carrying case

2. SAS IAQ control unit

3. Aluminium head

4. Battery charger

5. Remote control

6. “Clear” button

7. “Enter” button

8. Arrow “Up”

9. “Start” button

10. Arrow “Down”

11. Standing feet

12. Printer connection (not used)

13. Main switch

14. Serial number

15. CE mark

16. Charger connection

ENGLISH

Technical features

Model SAS IAQ Contact SAS IAQ Petri

Cat. No. 710-0868 710-0919

Airflow 100 l/min 100 l/min

Use with 55 mm contact plates 90 mm Petri dishes

Portable Yes Yes

Battery Rechargeable Rechargeable

Battery life 70 000 l 70 000 l

Intended use

Principle

The Surface Air System (SAS) encompasses several models which use the same principle. Air is aspirated at a fixed

speed for variable time through a head which has been machined with a series of specially designed small holes.

The resulting laminar airflow is directed onto the agar surface of a “RODAC plate” (or Petri dish) containing

medium for microbiological analysis.

When the selected sampling cycle is completed, the plate is removed and incubated. The organisms are then visible

to the naked eye and can be counted for the assessment of contamination levels.

The basic idea

The key features of the Surface Air System (SAS) are:

1. To use a simple and inexpensive “contact plate” (“SURFAIR PLATE”, “RODAC”) for surface, hand or air

control. These plates are very well known and easily available. They can be purchased ready poured with

different media.

2. To sample a known volume of air for a variable time to provide a range of sampling volumes.

3. To aspirate air in a laminar flow pattern with sufficient velocity to impact organisms onto an agar surface.

4. To accumulate data on the level of hygiene in each environment so that fluctuations can be monitored.

5. To take advantage of advanced electronics for more reliable results in different operating conditions.

6. To have the flexibility to choose between 55 mm contact plates or 90 mm standard Petri dishes.

ENGLISH

Brief operating instructions

Brief operating instruction for SAS Super IAQ

1. Press main switch.

2. Press ‘START’ button to sample the same air volume as the last sampling cycle.

3. To change the air volume, use the arrow buttons and select ‘USER MODE’ from the menu.

4. Refer to the instruction manual to change settings.

5. Press ‘ENTER’ to confirm selection.

6. Press arrows for menu selection to modify other pre-set parameters.

7. Press ‘ENTER’ to reach the sub menu of the chosen parameter.

8. Refer to the instruction manual to change settings.

9. Press ‘ON/OFF’ switch at the end of sampling operations.

10. Press ‘CLEAR’ each time you need to end an action. The unit will then return to the initial configuration.

Installation

Practical use of contact plates

1. Remove the aspirating head.

2. Insert an identified, closed and prepared plate and remove the plate lid.

3. Replace the aspirating head.

4. Select required air volume and start the unit. The airflow is directed onto the agar surface of the plate.

5. At the end of the cycle, remove the aspirating head.

6. Close and remove the plate.

7. Incubate.

8. Count the colonies, record the results on the microbiological air sampling report and read the results.

ENGLISH

List of menus and utility sub menus

START FOR XXX

This message indicates the air sampler is ready to sample the volume shown

(XXX) after pressing the ‘Start’ button

USER MODE Choose from 8 programmable sampling volumes

PROGRAM MODE Modify the 8 programmable sampling volumes

DELAY MODE Set a delayed start

UTILITY MODE This leads to the following sub menu:

SET TIME

To adjust the date and time

SET AUTOSWITCH

To disconnect the automatic switch-off when the “Infrared Remote” is used

DISPLAY RECORD

To show the recorded sampling data

CLEAR RECORD

To clear the recorded sampling data

LANGUAGE

To display text in different languages

IDENTIFY

To identify the operator’s name

SAMPLING SITE

To identify the sampling point

Preliminary inspection

The instrument is subject to specific quality tests before shipment and is carefully packed to avoid possible damage

during transit. However, a visible check should be carried out as soon as possible to determine any damage. This

must be reported immediately. The following procedures should be followed to check that the unit is working properly.

The instrument battery pack must be charged for at least 4 hours before running the test.

After the ‘ON/OFF’ button is pressed an automatic visual presentation will be displayed.

Holder adjustment

Contact plate and Petri dish holders can be adjusted (using a screw driver) in case the available plate is slightly

different in diameter from the standard 55 mm contact plate or 90 mm Petri dish.

Petri head adapter (optional)

An adapter is available in aluminium or stainless steel which allows the use of standard 90 mm Petri dishes with

SAS for contact plates.

ENGLISH

90 mm Petri dish filling

We recommend you fill the standard 90 mm disposable Petri dish with no more than 18 - 20 ml of agar to avoid the

medium touching the inside surface of the aspirating head.

Tripod installation (optional)

The SAS SUPER IAQ can be fixed to a table, floor tripod or wall support. The screw thread connection is located

under the unit, between the two front feet.

Functions

Software

Press the ‘ON/OFF’ switch (black button) to switch the unit on.

The ‘ON/OFF’ switch (black button) must be pushed twice to switch on the unit if the automatic switch-off timer was

used previously.

Press ‘CLEAR’ at any time to return to the initial ‘START FOR’ main screen.

The air sampler is provided with eight programmable air volumes (‘User Mode’) selectable by the operator.

Volume selection is made by pressing the “▲” or “▼” arrows when the programme is in the relevant sub menu.

Suggested air volumes:

- Contaminated areas (communities, processing rooms, etc) 10 - 200 litres of air

- Normal areas (laboratory benches, houses, etc) 200 - 500 litres of air

- Sterile or high-risk areas (cleanrooms, operating theatres, etc) 500 - 1000 litres of air

Starting with the same air volume as the previous sample

Switch on the unit by pushing the main switch. You will then see the following display with the last aspirated volume

of air:

Push the ‘START’ button to start a sampling cycle with the displayed volume of air.

‘USER MODE’

Up to eight additional volumes can be programmed into the unit. User-selectable volumes can be selected from the

‘USER MODE’, while the selectable volumes can be modified using the PROGRAM MODE’ function described in the

next paragraph.

Switch on the instrument and wait until the main screen is displayed:

ENGLISH

Press the “Up” or “Down” arrows to reach the:

Press the ‘ENTER’ button, now you can scroll the eight user-defined sampling volumes.

Once the desired sampling volume has been reached press the ‘ENTER’ button to confirm.

Press the ‘START’ button to begin the sampling cycle:

There are a total of eight available ‘“USER MODE’ programmes.

The maximum volume of air for each sampling cycle is 2000 litres.

‘PROGRAM VOLUME’ (modification of the value of a stored volume)

Using this procedure, it is possible to memorise up to eight different volumes (from 1 to 2000 litres of air). Switch on

the instrument and wait until the main screen is displayed.

Press the “Up” or “Down” arrows to reach the:

Press the ‘ENTER’ button, now you can scroll the eight user-selectable sampling volumes.

Select a volume by pressing the “UP” or “DOWN” arrows and then pressing ‘ENTER’ (value starts flashing):

ENGLISH

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere VWR Laborausrüstung Handbücher

VWR

VWR avantor 444-1343 Bedienungsanleitung

VWR

VWR avantor LED Digital Rotary Evaporator V17 Bedienungsanleitung

VWR

VWR 10860-660 Bedienungsanleitung

VWR

VWR 20EREEVWA Leitfaden

VWR

VWR avantor PCR Bedienungsanleitung

VWR

VWR PCR Bedienungsanleitung

VWR

VWR Standard 1000 Bedienungsanleitung

VWR

VWR VWR INCU-Line IL 10 Bedienungsanleitung

VWR

VWR Signature VE2/V2 Bedienungsanleitung

VWR

VWR Advanced Mini Block Heaters Bedienungsanleitung

VWR

VWR avantor 442-1266 Bedienungsanleitung

VWR

VWR 89209-862 Bedienungsanleitung

VWR

VWR 613-2891 Bedienungsanleitung

VWR

VWR Safetypette Bedienungsanleitung

VWR

VWR 5600 Series Betriebsanleitung

VWR

VWR Powerpette Pro Bedienungsanleitung

VWR

VWR VWR INCU-Line IL 10 Bedienungsanleitung

VWR

VWR AVANTOR E-BURETTE Bedienungsanleitung

VWR

VWR Standard Series Bedienungsanleitung

VWR

VWR 432-0367 Bedienungsanleitung

VWR

VWR VE2 Bedienungsanleitung

VWR

VWR HIGH PERFORMANCE PIPETTOR Bedienungsanleitung

VWR

VWR avantor 730-1461 Produktinformationsblatt

VWR

VWR avantor CHEMI Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung

Yamato

Yamato BM510 Bedienungsanleitung