WAGO Modular IO System INTERBUS S Bedienungsanleitung
Modular I/O System
INTERBUS S
Manual
Technical description,
installation and
configuration
750-132
Version 2.2.1
ii • General
Modular I/O System
INTERBUS S
Copyright ã1997-2001 by WAGO Kontakttechnik GmbH
All rights reserved.
WAGO Kontakttechnik GmbH
Hansastraße 27
D-32423 Minden
Phone: +49 (0) 571/8 87 – 0
Fax: +49 (0) 571/8 87 – 1 69
E-Mail: info@wago.com
Web: http://www.wago.com
Technical Support
Phone: +49 (0) 571/8 87 – 5 55
Fax: +49 (0) 571/8 87 – 4 30
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the correctness and com-
pleteness of this documentation. However, as errors can never be fully ex-
cluded we would appreciate any information or ideas at any time.
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally trademark or patent protected.
TABLE OF CONTENTS • iii
Modular I/O System
INTERBUS S
TABLE OF CONTENTS
Section 1: Explanations
Section 2: System Description INTERBUS S, Configuration,
Initial Starting, Diagnosis
Section 3: Digital Inputs
750-400, 750-401, 750-402, 750-403, 750-405, 750-406,
750-410, 750-411, 750-408, 750-409, 750-412, 750-413,
750-414, 750-415
750-404
Section 4: Digital Outputs
750-501, 750-502, 750-504, 750-516, 750-519
750-506
750-509
750-511
750-512, 750-513, 750-514, 750-517
Section 5: Analog Inputs
750-452, 750-454, 750-482, 750-484
750-456,
750-461, 750-481
750-462, 750-469
750-465, 750-466, 750-486,
750-467, 750-468, 750-487, 750-488
750-472, 750-474
750-476, 750-478
Section 6: Analog Outputs
750-550, 750-580
750-552, 750-554, 750-584
750-556
Section 7: End- and Supply Terminal Blocks
750-600, 750-614, 750-616
750-601, 750-602, 750-609, 750-610, 750-611, 750-612,
750-613, 750-615
750-622
Section 8: SSI Encoder Interface, Quadrature Encoder Interface
750-630, 750-631
Section 9: RS232, TTY, RS485
750-650, 750-651, 750-653
Section 0: Application in Explosive Environments
iv • Notes
Modular I/O System
INTERBUS S
INTERBUS S / General information
:$*2Ç,2Ç6<67(0
1
FUNCTION
IMPORTANT!
For fast, trouble free installation and start up of the devices described in this manual, the
user should carefully read and follow the advice and explanations offered in this guide.
Explanation of symbols used:
The EXCLAMATION POINT symbol is used when:
a) improper handling could cause damage or destruction of the hard- or software
b) possible injury to persons when interfacing to dangerous process peripherals.
The FINGER symbol describes routines or gives advice for the efficient use of the
devices and optimization of the software.
The FUNCTION symbol refers to helpful notes which are necessary for the correct
function. These remarks should be followed.
The QUESTION MARK gives an explanation of terms.
The symbol BOOKS gives references to additional literature, manuals and data sheets.
The user is most important to us:
We place great importance on the quality and user-friendliness of our manuals. Should
you have any ideas or suggestions for improvement to the contents or graphical design,
we would be glad to receive your proposals.
Notice:
This manual, including all illustrations, is copyrighted. Any use of this manual beyond
the terms of copyright is not allowed. The reproduction, translation, or use of the
electronic and mechanical information is subject to written authorization from WAGO
Kontakttechnik GmbH. Violations will be prosecuted. WAGO Kontakttechnik GmbH
reserves the right of alternation and changes. All rights in case of granting patents or
protective rights are reserved to WAGO Kontakttechnik GmbH.
In the case of non-WAGO products no reference to patent rights is given, but their
existence is noted. The use of the products described in this manuals exclusively
intended for experts trained in PLC programming or electrical engineering, who are
familiar with the national electrical standards in force. WAGO Kontakttechnik GmbH
and overseas subsidiaries will not accept any liability for faulty actions and damages
which occur on WAGO or non-WAGO products when disregarding the information
given in this manual. Any change made in WAGO hard or software (for example entries
in a register) will result in an exclusion of liability on the part of WAGO Kontakttechnik
GmbH.
INTERBUS S / General information
:$*2Ç,2Ç6<67(0
Table of contents chapter 2
1 The WAGO I/O SYSTEM 1
2 Buscoupler Interbus S 2
2.1 Buscoupler-Hardware 2
2.2 Supply voltage - Electronics 3
2.3 Supply voltage - Field Side 4
2.4 Bus connection and station address 5
3 Enclosure and technical data 8
4 Interbus S 9
4.1 Interface Modules 9
4.2 Configuration software 10
5 Configuration of the fieldbus node in the master
controller
5.1 Identification code
11
11
5.2 ID Code for WAGO I/O System 12
5.3 IBS CMD Software 13
5.4 Example of application 19
6 Starting of operation and diagnostics 21
7 General conditions 23
7.1 Tansport and storing conditions 23
7.2 Mechanical and climatic conditions 23
7.3 Isolation, class of protection and degree of protection 24
7.4 Electromagnetic compatibility 25
7.5 Power supply 25
Interbus / Introduction
:$*2Ç,2Ç6<67(0
1
1 The WAGO I/O System
The WAGO I/O SYSTEM consists of various components which are capable of
providing modular and application specific fieldbus nodes for various fieldbusses.
I11.1 Setting up a fieldbus node with the WAGO I/O SYSTEM
General remark:
A fieldbus node consists in principle of a fieldbus coupler at the front end, a number of
special function modules and a termination module which is placed at the other end.
1 - Buscoupler
The Buscoupler forms the link between the fieldbus and the field devices with their I/O
functions. All control functions required for the faultless operation of the I/O functions
are carried out by the coupler. The connection to different fieldbus systems is
established by each of the corresponding Buscouplers, e.g. for PROFIBUS, INTERBUS
S, II/O LIGHTBUS, CAN, ModBus etc. In this way a change of the fieldbus system is
possible.
2 - Function modules
In the function modules, the incoming process data ais converted. Corresponding to the
different requirements, special function modules are available for a variety of functions.
There are digital and analog inputs and outputs and modules for special functions. The
modules are described in the following chapters.
3 - Termination module
A termination module is needed for faultless operation of the node. The termination
module is always placed as the last module in order to obtain a termination of the
fieldbus node. This module has no I/O function.
Interbus / Introduction
:$*2Ç,2Ç6<67(0
2
Assembly of the WAGO I/O System
All components of the system can be snapped directly on a carrier rail according to EN
50022 (DIN 35).
When snapping the analog or digital components onto the rail, no special sequence must
be observed. The secure positioning and connection of the individual function modules
and the coupler is provided by a snap-in system. This snap-in system provides automatic
interlocking onto the DIN rail assembly. It is always possible to remove a function
module or the Buscoupler from the assembly by pulling the orange pull-tab.
Please note, that the power supply of the field side as well as the data transmission are
interrupted. It has to be ensured that the interruption of PE will not put personnel or
equipment in danger.
With a CAGE CLAMP, conductors with a cross section of 0.08 to 2.5mm2/AWG 18-14
can be connected. Vibration proof, fast and maintenance-free. You simply introduce a
screwdriver or an operating tool into the operating slot under the clamping unit. The
CAGE CLAMP spring is pressed down. You can now introduce the wire into the
clamping unit. Withdraw the operating tool and the conductor is automatically clamped.
Interbus / Introduction
:$*2Ç,2Ç6<67(0
3
The clamping force adjusts automatically to the conductor cross section. The flat
clamping face of the CAGE CLAMP spring presses the conductor against the current
bar without damage. Any deformation or movement of the conductor is compensated,
thus eliminating the risk of a loose connection. The contact point between conductor
and CAGE CLAMP is well protected against corrosive deterioration. This connection is
made fast and, furthermore, it is maintenance-free. There is no need for costly periodical
examination of the connections.
The supply modules of the WAGO I/O system are partly equipped with a fuse holder.
This fuse holder can be pulled out in order to break the circuit of the following modules.
To do so, you first have to insert a screwdriver into one of the slots on both sides in
order to pull out the front side of the fuse holder.
The front side now being hinged down makes it possible to remove or to insert the fuse.
After that, you lift up the front side again and push the fuse holder back into its original
position.
INTERBUS S / Buscoupler
:$*2Ç,2Ç6<67(0
3
2 Buscoupler - INTERBUS S
2.1 Buscoupler - Hardware
Ill. 2: The INTERBUS buscoupler
The 750-304 Interbus coupler consists of two major electronic sub systems:
left side:
This housing contains the electronics for the coupling to the bus, the processor
and the fieldbus connection. (ill. 2.1)
right side:
This housing contains the DC to DC converter and power distribution for the internal K
bus, local processor and external 24 V DC connections to other discrete I/O modules.
Illustration 2.2 identifies the 24 V DC connection points to supply voltage to I/O
modules. Illustration 2.3 identifies the ground connection.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere WAGO E/A-System Handbücher
WAGO
WAGO 750-530 Bedienungsanleitung
WAGO
WAGO 753-482 Bedienungsanleitung
WAGO
WAGO WAGO-I/O-SYSTEM 750 Series Bedienungsanleitung
WAGO
WAGO 750-540 Bedienungsanleitung
WAGO
WAGO WAGO-I/O-SYSTEM 750 Series Bedienungsanleitung
WAGO
WAGO 750-404 Bedienungsanleitung
WAGO
WAGO 750 Series Bedienungsanleitung
WAGO
WAGO I/O-SYSTEM 750-517 Bedienungsanleitung
WAGO
WAGO 750-491 Bedienungsanleitung
WAGO
WAGO WAGO-I/O-SYSTEM 750 Series Bedienungsanleitung
WAGO
WAGO IO-SYSTEM 750-415 Bedienungsanleitung
WAGO
WAGO 750-643 Bedienungsanleitung
WAGO
WAGO WAGO-I/O-SYSTEM 750 XTR Series Bedienungsanleitung
WAGO
WAGO 750-484 Bedienungsanleitung
WAGO
WAGO WAGO-I/O-SYSTEM 752 Bedienungsanleitung
WAGO
WAGO I/O SYSTEM 750 750-635 Bedienungsanleitung
WAGO
WAGO LONWORKS 750-319 Bedienungsanleitung
WAGO
WAGO WAGO-I/O-SYSTEM750 Bedienungsanleitung
WAGO
WAGO 750-438 Bedienungsanleitung
WAGO
WAGO I/O SYSTEM 750 Bedienungsanleitung
Beliebte E/A-System Handbücher anderer Marken
Teknim
Teknim TWM-1887 Bedienungsanleitung
Intelligent Appliance
Intelligent Appliance IA-2662-E Bedienungsanleitung
BERGHOF
BERGHOF ECC DIO 16/16 Bedienungsanleitung
Advantech
Advantech PCM-27J3AU Installations- und Betriebshandbuch
Festo
Festo CP-E08-M12-CL Bedienungsanleitung
Measurement Computing
Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung
