WANHAO DUPLICATOR 9 Bedienungsanleitung

DUPLICATOR 9

GETTING

Thanks for choosing Wanhao 3D Printer products. You’re just moments away from printing your rst 3D

model. It’s important that you follow these steps carefully to ensure correct setup of your 3D Printer.

STARTED

GUIDE

You can also visit www.wanhao3dprinter.com/Video/D9 video/wanhao D9 unboxing

for step by step guide on unboxing and setup, levelling, lament installation and printing.

Package Contents:

1 x WANHAO 3D Printer

1 x Filament Spool Holder

1 x Filament Spool Stand

1 x Power Cable

1 x USB Cable

1 x 8GB SD Card

1 x Hex Screw Driver

1 x Hex Key Set

6 x Hex Bolts

2 x Plastic belts

1 x 1.75mm PLA Filament

1 x Needle for unclugging nozzle

ASSEMBLING AND MOUNTING

1Take out all components

from the box and

place them on the at

ground.

1-Base

2-Z axis Tower Pillar*2

3-X axis rail

4-X axis gantry

5-MK12 Extruder

Place the Base on

it’s side. Find the Z

axis pillar with sticker

No.2. Slide the No.2

pillar into the base

vertical locker. Then

tighten the bolt at

bottom of base.

4 5

Insert the leveling

card or an A4 paper

between the nozzle

and bed. Adjusting

the Z axis height,

until you can feel the

friction while moving

the card or paper.

Click the upper Z to move

extruder up and click the

lower Z to move extruder

down. Stop clicking until

you feel the leveling card

getting friction while

moving the card.

Click NEXT to initiate

auto leveling.

Congratulation! You have nished bed leveling. For video installation,

please scan the QR code.

Video Installation Ofcial Website Wanhao Store

To move the extruder

by hand to 4 corners

separately. Adjusting

the knob at each

corner, until you feel

friction while moving

the leveling card.

CONSTRUCT AND CONNECT [CONT.]

3Tighten the locking

bolt clockwise. Then

install the other Z

axis pillar onto the

Base.

Loose the two locking

bolt on No.3 and No.4

Z axis pillar by around

5mm. So there will be

sufcient space for X axis

pillar to slide in.

5Slide the X axis pillar into

the No.3 and No.4 bolts. If

there’s not enough space,

you may need to re-loose

the locking bolt.

To tighten the locking

bolt through the hole on

top of the X axis pillar.

Lock both No.3 and No.4

pillar.

7Insert the plastic cover

onto the two ends of X

axis pillar.

Note: Please double

check the Z axis and X

axis pillars. If any bolt

not secured. You need

to secure the screws to

ensure the gantry are

steady and tight.

Rotate the cylinder holder

for a bit but not too close.

Tight enough that can not

slide into pillar freely.

This is also same to the

other side with stickers

No.6.

9Mount the X axis rail.

Align the right and left

side holders rst. Please

make sure the rail is

located in the middle

of the X axis. You may

need to adjust the

distance to both ends

through the cylinder

holders.

Then tighten the bolts

on both end of No.5 and

No.6.

11 Mount the MK12

extruder onto the

X axis holder. Make

sure the locking holes

match to the holder

holes.

A total of 4 bolts need

to be tightened, but the

rst bolt should not be

too tight until the other

three bolts are mounted,

then tighen all the bolts

together.

WIRING INSTRUCTION

B C

LEVELING BEFORE PRINTING

1Turn the couple to lower the

two Z axis in order to level

the two Z axis at same height.

Note: The ruler or height

gauge would provide more

accurate height for both two

Z axis. The two axis need to

be at same height.

Turn on the printer.

Release the 4 bed

leveling nuts by 4-5

turns. Then Click LEVEL.

Read the instruction, then

click NEXT.

CONSTRUCT AND CONNECT [CONT.]

3Tighten the locking

bolt clockwise. Then

install the other Z

axis pillar onto the

Base.

Loose the two locking

bolt on No.3 and No.4

Z axis pillar by around

5mm. So there will be

sufcient space for X axis

pillar to slide in.

5Slide the X axis pillar into

the No.3 and No.4 bolts. If

there’s not enough space,

you may need to re-loose

the locking bolt.

To tighten the locking

bolt through the hole on

top of the X axis pillar.

Lock both No.3 and No.4

pillar.

7Insert the plastic cover

onto the two ends of X

axis pillar.

Note: Please double

check the Z axis and X

axis pillars. If any bolt

not secured. You need

to secure the screws to

ensure the gantry are

steady and tight.

Rotate the cylinder holder

for a bit but not too close.

Tight enough that can not

slide into pillar freely.

This is also same to the

other side with stickers

No.6.

9Mount the X axis rail.

Align the right and left

side holders rst. Please

make sure the rail is

located in the middle

of the X axis. You may

need to adjust the

distance to both ends

through the cylinder

holders.

Then tighten the bolts

on both end of No.5 and

No.6.

11 Mount the MK12

extruder onto the

X axis holder. Make

sure the locking holes

match to the holder

holes.

A total of 4 bolts need

to be tightened, but the

rst bolt should not be

too tight until the other

three bolts are mounted,

then tighen all the bolts

together.

WIRING INSTRUCTION

B C

LEVELING BEFORE PRINTING

1Turn the couple to lower the

two Z axis in order to level

the two Z axis at same height.

Note: The ruler or height

gauge would provide more

accurate height for both two

Z axis. The two axis need to

be at same height.

Turn on the printer.

Release the 4 bed

leveling nuts by 4-5

turns. Then Click LEVEL.

Read the instruction, then

click NEXT.

DUPLICATOR 9

GETTING

Thanks for choosing Wanhao 3D Printer products. You’re just moments away from printing your rst 3D

model. It’s important that you follow these steps carefully to ensure correct setup of your 3D Printer.

STARTED

GUIDE

You can also visit www.wanhao3dprinter.com/Video/D9 video/wanhao D9 unboxing

for step by step guide on unboxing and setup, levelling, lament installation and printing.

Package Contents:

1 x WANHAO 3D Printer

1 x Filament Spool Holder

1 x Filament Spool Stand

1 x Power Cable

1 x USB Cable

1 x 8GB SD Card

1 x Hex Screw Driver

1 x Hex Key Set

6 x Hex Bolts

2 x Plastic belts

1 x 1.75mm PLA Filament

1 x Needle for unclugging nozzle

ASSEMBLING AND MOUNTING

1Take out all components

from the box and

place them on the at

ground.

1-Base

2-Z axis Tower Pillar*2

3-X axis rail

4-X axis gantry

5-MK12 Extruder

Place the Base on

it’s side. Find the Z

axis pillar with sticker

No.2. Slide the No.2

pillar into the base

vertical locker. Then

tighten the bolt at

bottom of base.

4 5

Insert the leveling

card or an A4 paper

between the nozzle

and bed. Adjusting

the Z axis height,

until you can feel the

friction while moving

the card or paper.

Click the upper Z to move

extruder up and click the

lower Z to move extruder

down. Stop clicking until

you feel the leveling card

getting friction while

moving the card.

Click NEXT to initiate

auto leveling.

Congratulation! You have nished bed leveling. For video installation,

please scan the QR code.

Video Installation Ofcial Website Wanhao Store

To move the extruder

by hand to 4 corners

separately. Adjusting

the knob at each

corner, until you feel

friction while moving

the leveling card.

Andere Handbücher für DUPLICATOR 9

Inhaltsverzeichnis

Andere WANHAO 3D-Drucker Handbücher

WANHAO

WANHAO GADOSO REVOLUTION 2 Bedienungsanleitung

WANHAO

WANHAO Duplicator 8 MARK I Bedienungsanleitung

WANHAO

WANHAO Duplicator 5 Bedienungsanleitung

WANHAO

WANHAO Duplicator 7 Plus Bedienungsanleitung

WANHAO

WANHAO MARK II Duplicator 6 Plus Bedienungsanleitung

WANHAO

WANHAO Duplicator 10 Bedienungsanleitung

WANHAO

WANHAO DUPLICATOR I3 MINI Bedienungsanleitung

WANHAO

WANHAO Duplicator Five Bedienungsanleitung

WANHAO

WANHAO DUPLICATOR 7 Bedienungsanleitung

WANHAO

WANHAO Duplicator 6 Bedienungsanleitung

WANHAO

WANHAO Duplicator 5S Bedienungsanleitung

WANHAO

WANHAO Duplicator i3 Bedienungsanleitung

WANHAO

WANHAO I3 Plus Bedienungsanleitung

WANHAO

WANHAO Duplicator 5S Bedienungsanleitung

WANHAO

WANHAO Duplicator 3/4 Bedienungsanleitung

WANHAO

WANHAO Duplicator i3 Handbuch

WANHAO

WANHAO CGR Series Bedienungsanleitung

WANHAO

WANHAO Duplicator I3V2 Bedienungsanleitung

WANHAO

WANHAO Duplicator I3V2 Bedienungsanleitung

WANHAO

WANHAO DUPLICATOR 9 Bedienungsanleitung

WANHAO

WANHAO GADOSO GR1 Bedienungsanleitung

WANHAO

WANHAO DUPLICATOR 7 Bedienungsanleitung

WANHAO

WANHAO Duplicator i3 Merkblatt

WANHAO

WANHAO Duplicator i3 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch