Wayne-Dalton 523RX Bedienungsanleitung

Some installation tasks listed in

this document are found in other

documents.

Please refer to the appropriate

document(s) as directed;

308577 Hilti Kwik Bolt Installation

found on Ribbon Connect

41510.00119 Installation

Instructions for Motor Enclosure

(Included)

This installation manual provides

the trained door technician

information required to install

this door.

READ COMPLETE INSTRUCTIONS

BEFORE INSTALLING DOOR.

This manual is intended ONLY

for professional use by a trained

door systems technician. All

others please refer to the end

user manual provided to you.

INSTALLATION INSTRUCTIONS

MODEL 523RX RESIDENTIAL EXTERIOR SECURITY SHUTTER,

WITH SIDE MOUNT MOTOR ENCLOSURE

After installation is complete,

leave this manual with the

Homeowner. Maintenance

instructions on page 20.

TABLE OF CONTENTS

SECTION CONTENTS PAGES

1 SAFETY INFORMATION 3

2KEY DRAWING 4

3DOOR INSTALLATION DATA SHEET 5

4PREINSTALLATION CHECK LIST 6

5 INSTALLATION 7-14

6MOTOR WIRING 15-17

7FINAL INSTALLATION 18-19

MAINTENANCE INSTRUCTIONS 20

WARRANTY 21

Potential Hazard Eect Prevention

MOVING DOOR

WARNING

Could result in Death

or Serious Injury

Keep people clear of opening while Door is moving.

Do NOT allow children to play with the Door Operator.

Do NOT operate a Door that jams or one that has a broken spring.

ELECTRICAL SHOCK

WARNING

Could result in Death

or Serious Injury

Turn OFF electrical power before wiring switch and motor to supply.

HIGH SPRING TENSION

WARNING

Could result in Death

or Serious Injury

Do NOT try to remove, install, repair or adjust springs or anything to which door spring parts are fastened, such as,

wood blocks, steel brackets, cables or other like items.

Installations, repairs and adjustments must be done by a trained door system technician using proper tools and

instructions.

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

SECTION 1 - SAFETY INFORMATION

Upward Rolling Doors doors are large, heavy objects that move with the help of electric motors. Since moving objects and electric motors can

cause injuries, your safety and the safety of others depends on you reading the information in this manual. If you have any questions or do

NOT understand the information presented, call technical support at 1-800-764-1457.

WARNING

In this section and those that follow, the words "DANGER", " WARNING", and "CAUTION" are used to stress important safety information. The

word:

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage.

The word NOTE is used to indicate important steps to be followed or important considerations.

FIG 2

Please note that components and component locations are shown here for REFERENCE ONLY.

Your unit installation and component locations may be dierent.

SECTION 2 - KEY DRAWING

A sample of the “DOOR INSTALLATION DATA” sheet is shown here. Locate the work

order “Door Installation Data” sheet inside the door hardware box. You will need to

refer to the “Door Installation Data”sheet. See FIG 2.

Factory order number on door components must match with factory order number

on the “Door Installation Data” sheet. Each door has it’s own individual sheet.

FIG 2

SAMPLE

SECTION 3 - DOOR INSTALLATION DATA SHEET

Verify that the door installation can be accomplished before proceeding:

• Locate the work order “DOOR INSTALLATION DATA” sheet, see FIG 2, inside the door hardware box.

• Does the wall opening shown in FIG 3 match the Opening Width and Height shown on the “Door Installation Data” sheet?

• Are the guides you received suitable for the jambs? Compare the guides type shown on the “Door Installation Data” sheet with FIG 4.

• Can the guides be installed plumb?

• Check the sill for level. If sill is not level, mark the high sill location on the low side jamb.

• Guides are designed to rest on sill.

Header

Opening

Height

Jamb

Sill

Opening Width

FACE OF WALL MOUNT

BETWEEN JAMB MOUNT

FIG 4

SECTION 4 - PRE-INSTALLATION CHECK LIST

FIG 3

• Mount curtain guides to the surface using supplied fasteners. See FIG 5A and 5B.

• Check “G”Dimension as illustrated in FIG 4 on page 5. “G”Dimension must match your “DOOR INSTALLATION DATA” sheet.

• Both guides MUST be on a level line and both

guides MUST be plumb.

• The “G”Dimension must be held within 1/8”over

the entire height of the guides.

STEP 1STEP 1 INSTALL CURTAIN GUIDES TO JAMB

SECTION 5 - INSTALLATION

FIG 5

Follow instructions and use proper

lifting equipment and correct lifting

procedure to avoid serious injury or

death.

WARNING

STEP 2STEP 2 INSTALL HEAD ASSEMBLY

SECTION 5 - INSTALLATION

• Lift the head assembly using a fork lift or other appropriate lifting equipment and lower

it onto the top of the guides, inserting the support bars into the guide as shown in FIG 6.

• Be sure the support bars are fully inserted into the guides on both sides. See FIG 7

• Install the wall fasteners provided into the head plate anges to attach it to the jamb.

See FIG 7

FIG 6

Rapidly closing curtain could result in death or serious injury. Do not

remove factory binding around curtain assembly until step 3.

WARNING

FIG 7

STEP 2STEP 2 INSTALL HEAD ASSEMBLY (Continued...)

SECTION 5 - INSTALLATION

• Lift the fascia plate using a fork lift or other appropriate lifting equipment and lower it, attaching it to the back of the jamb, as shown in FIG 8.

• Be sure the bottom of the fascia plate is approximately 4-1/2”below the top of the guides, leveled and centered; Fasten it with wall fasteners. See FIG 9 and FIG 10.

• Install the wall fasteners provided into the head plate anges to attach it to the jamb. See FIG 10.

FIG 10

FIG 8

FIG 9

STEP 3STEP 3 WIND SPRINGS

SECTION 5 - INSTALLATION

Prior to winding or making adjustments to the springs, ensure you are winding

in the proper direction as stated in the Installation Instructions. Otherwise the

spring ttings may release from spring if not wound in the proper direction

and could result in severe or fatal injury.

WARNING

Winding torsion spring(s) is an extremely dangerous procedure and should be

performed only by a trained door system technician using proper tools and

instructions.

WARNING

Rapidly closing curtain could result in death or serious injury. Use caution

when lowering curtain before spring tension is applied.

WARNING

• Cut the banding and carefully lower the curtain into the guides to the fully closed position.

• Using a 1-1/2” open end wrench wind the spring by turning the Winding Nut the specied

number of turns indicated on your door installation data sheet. The winding direction would be

the same as the direction to open the door for both left and right hand drive. See FIG 11.

• Check the balance of the door. If needed raise the door and adjust the number of turns to

achieve proper balance.

FIG 11

Inhaltsverzeichnis

Andere Wayne-Dalton Garagentoröffner Handbücher

Wayne-Dalton

Wayne-Dalton 8100 Kurzanleitung

Wayne-Dalton

Wayne-Dalton idrive pro 3790 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9800 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 7400 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 6600 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 9800 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 105/110 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 7100 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8000 Series Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8300 Kurzanleitung

Wayne-Dalton

Wayne-Dalton Windload Post 9100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 3790 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 44 Double Flush Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton Quantum 3000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8500 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 9100 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 105 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9100 Kurzanleitung

Wayne-Dalton

Wayne-Dalton TorqueMaster Plus 9800 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9700 Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung