Weidmann InsuLogix T Bedienungsanleitung
InsuLogix® T Portable One Channel Manual Page 1
InsuLogix® T Portable One Channel
Temperature Measurement System
Manual
Weidmann Technologies Deutschland GmbH
Washingtonstraße 16/16a
D-0113 Dresden, Germany
Telefon: +4 (0)351 8435 0
Version 1.2
InsuLogix® T Portable One Channel Manual Page 2
Contents
1.
General..................................................................................................................................... 3
2.
Safety ....................................................................................................................................... 3
3.
Unpacking, Inspection, Service ............................................................................................... 3
4.
Introduction ............................................................................................................................. 4
5.
Product specifications.............................................................................................................. 5
6.
Calibration ............................................................................................................................... 5
7.
Getting started.......................................................................................................................... 6
Sensor handling........................................................................................................................... 6
Connection with PC .................................................................................................................... 6
Connecting the probes................................................................................................................. 6
Testing the temperature probe..................................................................................................... 7
Temperature probe handling ....................................................................................................... 7
Cleaning of sensor connectors and plugs.................................................................................... 8
8.
Software................................................................................................................................... 9
9.
Using the InsuLogix® T FoTemp one channel handheld device ............................................ 9
Figure 1 Connecting the fiber optic probe to instrument................................................................ 7
Figure 2 Bending restrictions.......................................................................................................... 8
Figure 3 Mechanical restrictions..................................................................................................... 8
Figure 4 Fiber optic connector cleaning tool .................................................................................. 8
Figure 5 Connect the fiber optic probe is connected to handheld device ....................................... 9
Figure 6 Instrument switched on and reading the temperature....................................................... 9
Figure 7 Press Menu/Enter key longer than one second to display Menu option......................... 10
Figure 8 Switching ON/OFF the LCD backlight.......................................................................... 10
InsuLogix® T Portable One Channel Manual Page 3
1. General
The fiber optical thermometer described in the operating instructions has been designed and
manufactured using state-of-the-art technology.
All components are subject to stringent quality and environmental criteria during production.
These operating instructions contain important information on handling the instrument. Working
safely requires that all safety instructions and work instructions are observed.
Observe the relevant local accident prevention regulations and general safety regulations for the
instrument‘s range of use.
The operating instructions are part of the product and must be kept in the immediate vicinity of
the instrument and readily accessible to skilled personnel at any time. Skilled personnel must
have carefully read and understood the operating instructions prior to beginning any work.
The manufacturer‘s liability is void in the case of any damage caused by using the product
contrary to its intended use, non-compliance with these operating instructions, assignment of
insufficiently qualified skilled personnel or unauthorized modifications to the instrument. The
general terms and conditions contained in
The sales documentation shall apply. Subject to modifications.
Further information: internet-adress: www.optocon.de
2. Safety
Skilled personnel
Skilled personnel are understood to be personnel who, based on their technical training,
knowledge of measurement and control technology and their experience and knowledge of
country-specific regulations, current standards and directives, are capable of carrying out the
work described and independently recognizing potential hazards.
3. Unpacking, Inspection, Service
When unpacking and inspecting your system components, you need to do the following:
1. Check all materials against the enclosed packing list.
2. Carefully unpack and inspect all components for visible damage.
3. Save all packing materials, until you have inspected all components and find that there is no
obvious or hidden damage.
4. Before shipment, each instrument is assembled, calibrated, and tested. If you note any
damage or suspect damage, immediately contact us.
In case of a malfunction or service request please use our technical support which can be
contacted by telephone Monday-Friday between 8:30 to 17:00 CET: +4 (351) 8435 0 or
email: info@optocon.de
InsuLogix® T Portable One Channel Manual Page 4
Send RMA shipments to:
Weidmann Technologies Deutschland G BH
Washingtonstrasse 16/16a17, 01139 Dresden,
Germany
Disposal
Inoperable instruments must be disposed of in compliance with local regulations for electronic
materials.
4. Introduction
The InsuLogix® T FoTemp 1 channel-optical fiber thermometer is used for measuring
temperature in an environment with High electromagnetic interference, or with the presence of
high power microwave fields. It can also be used in places where measurement with an electric
temperature probe is not possible.
With the InsuLogix® T Fotemp1 handheld you are able to operate a comfortable and safe
temperature measurement, even in difficult situations, with an overwhelming aggregated system
accuracy of ± 0.2°c.
Fotemp1 handheld is a compact, user-friendly, and easy to operate instrument for many fields of
application, e.g.:
•medical engineering such as nuclear spin tomography
•high frequency heating processes
•microwave power heating processes
•electric motors
•generators and transformers
•aeronautical engineering
•chemistry and petro chemistry
The outer jacket of the fiber optic temperature sensors is made out of Teflon, at the sensor tip a
GaAs crystal (Gallium Arsenide) is attached. The probe sensor is completely non-conductive.
Weidmann’s fiber optic sensors offer complete immunity to RF and microwave radiation with
high temperature operating capability, intrinsic safety, and non-invasive use. The probes are
also designed to withstand harsh and corrosive environments.
Starting at a light wave length of 850nm GaAs becomes optical translucent. Since the position
of the band gap is temperature dependent, it shifts about 0.4nm/kelvin. The measurement
device contains a light source and a device for the spectral detection of the band gap. This
guaranties fast, repeatable and reproducible measurements. The measurement results can be
easily monitored via the analog outputs and “FoTemp-Assistant” software. Over the entire life of
the system calibration is not required to remain within the specifications.
InsuLogix® T Portable One Channel Manual Page 5
5. Product specifications
Instrument specifications
Number of channels 1
Power Requirements VDC, power pack included
Current
1.5 A
Display range 0 to 300°C
Accuracy
up to ± 0.2°C
Resolution 0.1°C
Communication
RS-232
Display: LCD display 1x8 digits, background lighting
Storage temperature:
-20°C to +50°C
Operating temperature: 0°C to +40°C
Probe
specifications
Accuracy
± 0.2°C
Length 2m, 5m or 10 m, different probe lengths and
configurations on request
Diameter
1,3 mm (probe tip 2cm, OD 1,7mm), totally
made of nonmetallic material
Time constant < 1°C in case of temperature-fluctuations
Temperature range (probe): 0°C to 300°C
Connector ST-Connector
System-accuracy (Instrument and probe) ± 2°C in the temperature range 0°C - 300°C
Calibration One-point temperature calibration by the user
possible
Accuracy close to the calibration point ± 0,1°C
Table 1 Instrument and probes specifications
6. Calibration
To ensure an accurate temperature measurement in critical areas, we offer a comprehensive
calibration service for our fiber optic temperature measurement instruments. Through our
modern labs and our qualified staff we can guarantee you a very accurate and fast calibration.
Within a few days you get your unit back and can start your fiber optic measurement projects.
For each calibrated measurement instrument by us, a full certificate of test results is supplied.
Your fiber optical thermometer comes factory calibrated.
An annual re-calibration is not necessary, except for internal company regulations. All
calibrations are performed at our factory. For each calibrated measurement instrument by us, a
full certificate of test results is supplied.
Your account manager is available Monday to Friday 8:30 to 17:00 personally by phone
+4 (351) 8435 0. In addition, you are welcome to send an email message to tell us your
concern. We will get in touch with you as soon as possible.
InsuLogix® T Portable One Channel Manual Page 6
7. Getting started
1. Plug the provided optical fiber temperature sensors to the ST-connector on the upper of the
instrument, where the ON/OFF switch in located.
2. Connect the provided RS-232 interface cable to the thermometer and a free serial port of the
pc or notebook.
3. Use the provided power supply to power up the system.
4. After powering and switching the thermometer on, temperature values will be displayed if
sensor‘s level is above 20% signal strength
5. The thermometer is ready for measurement.
Caution! The fiber optical thermometer only functions with Weidmann fiber optic temperature
sensors. Please do not use temperature sensors of other brands.
Please read the instructions for installing the fiber optic instrument carefully.
Sensor handling
The sensor consists of a ST-connector at the end and a gallium arsenide crystal at the tip of the
sensor. The crystal is sensitive and should not be exposed to excessive mechanical stress.
Please please note the information about the bending radius of the sensor on page 16. A
forcible bending of the sensor leads to breakage of the fiber. In this case the sensor is damaged
and needs to be repaired / replaced.
Connection with PC
Before establishing the first connection, please check whether the InsuLogix T device is
connected to the power supply and the pc via the rs-232 cable respectively.
Connecting the probes
The temperature sensors are connected via the ST-connectors to the BNC sockets at the back
panel. Please note to insert the plugs pushing slightly against the spring pressure and to turn
with a clockwise rotation. All fiber optical temperature probes can be connected.
Important: All channels and probes not in use must be protected with supplied dust caps.
InsuLogix® T Portable One Channel Manual Page 7
Figure 1 Connecting the fiber optic probe to instrument
To ensure accurate measurements and long life of the fiber optic sensors and instruments, it is
necessary to clean them regularly. More information about cleaning can be found in a later
chapter.
Testing the temperature probe
To test the functionality of the sensor, you can place the sensor into a test liquid, of which the
temperature is known (e.g. boiling water). The sensor will respond with the given temperature
within a few seconds.
If no temperature is displayed please re-install the software and check if the sensor has contact
to the measuring object
Temperature probe handling
200µm silica core fiber
S
hort time (max. 24h) bending radius: not less than 4 cm.
Permanent installation bending radius: not less than 8cm.
400µm silica core fiber
S
hort time (max. 24h) bending radius: not less than 8 cm.
Permanent installation bending radius: not less than 16 cm.
InsuLogix® T Portable One Channel Manual Page 8
Figure 2 Bending restrictions
Figure 3 Mechanical restrictions
Cleaning of sensor connectors and plugs
Weidmann is optionally supplying a fiber optic one-click cleaner. The tool is simple and quick to
use as is shown in image below.
Figure 4 Fiber optic connector cleaning tool
InsuLogix® T Portable One Channel Manual Page
8. Software
For a description of usable software read the following documents:
- InsuLogixT_Manual_FOTEMP_Assistent_EN_Rev01.pdf (English version)
- InsuLogixT_Manual_FOTEMP_Assistent_DE_rev01.pdf (German version)
9. Using the InsuLogix® T FoTemp one channel handheld device
Figure 5 Connect the fiber optic probe is connected to handheld device
Figure 6 Instrument switched on and reading the temperature
InsuLogix® T Portable One Channel Manual Page 10
Note: The signal level received from sensor must be at least 20% in order for instrument to
calculate the temperature.
Figure 7 Press Menu/Enter key longer than one second to display Menu option
Use the UP and DOWN keys to enter the desired OFFSET. Save and exit menu pressing the
„MENU/ENTER“ key
Figure 8 Switching ON/OFF the LCD backlight
Press key „UP“ to see second menu option „Light“ (press UP or DOWN key to switch backlight
on or off, execute with „MENU/ENTER“ key)
Andere Handbücher für InsuLogix T
1
Inhaltsverzeichnis
Andere Weidmann Messgerät Handbücher
