Weinmann MEDUMAT Standard 2 Technische Daten

Changing the ventilation mode

Requirements:

• The device is switched on.

• A ventilation mode is set.

1. Brieﬂy press the menu button .

2. Select the Mode ﬁeld.

3. Select a ventilation mode.

4. Adjust the ventilation parameters and press start.

Ventilating the patient

Selecting emergency mode

1. Brieﬂy press the On/Off button .

2. Select emergency mode:

• Emergency Pediatric

• Emergency Child

• Emergency Adult

Selecting previous patient

1. Brieﬂy press the On/Off button .

2. Select Previous patient ﬁeld.

RSI mode

Performing RSI ventilation

Requirements:

• The device is switched on.

• The MEDUtrigger is connected to the device.

• RSI was set as the ventilation mode for a

new patient. The Demand function is

automatically activated.

1. For the function Manual, navigate to the

ﬁeld Demand.

2. Select the Manual ﬁeld.

3. To perform continuous ventilation

following successful airway management,

select the Contin. ﬁeld. The device

switches to IPPV mode.

Selecting a new patient

1. Brieﬂy press the On/Off button .

2. Select New patient ﬁeld.

3. Select height and gender or navigate to the

Height ﬁeld and turn the navigation knob further

to select the desired patient group.

4. Press the navigation knob next.

5. Select a ventilation mode.

6. If necessary: Adjust the ventilation parameters and

press start.

Pausing the ventilation

Requirements:

• Cardiac rhythm analysis or deﬁbrillation

is being performed.

• The device is switched on.

• The CPR mode is set.

• Continuous ventilation

is activated.

1. Select the Pause ﬁeld.

The ventilation is paused for 50 seconds.

CPR mode

Performing CPR ventilation

Requirements:

• The device is switched on.

• The MEDUtrigger is connected to the device.

• A ventilation mode for a new patient is set.

1. Brieﬂy press the CPR button .

The device switches to the mode CPR 30:2/CPR 15:2/CPR IPPV (depending on

the preset). The green LEDs on the MEDUtrigger light up.

2. If necessary:

Change algorithm:

• 30:2

• 15:2

• Continuous

3. Press and hold the MEDUtrigger button

during the ventilation phase until two

mechanical breaths are performed.

4. To exit the CPR mode,

press the CPR button again.

To enable the selection of the function Manual, a MEDUtrigger must

be connected. Otherwise, this function will not be displayed.

If you do not select a menu within 20 seconds, the device automati-

cally switches to the Previous patient menu and immediately begins

ventilation of the patient. In this case, the device uses the ventilation mode

and ventilation parameters set for the last patient to be ventilated. To switch

off the countdown before the 20 seconds have elapsed, move one of the

navigation knobs.

MEDUMAT Standard2MEDUMAT Standard2

Brief operating instructions

MEDUMAT Standard2

Charging the battery

Charging the battery in the device

1. Slide battery into the battery compartment until it clicks into place.

2. Insert the portable system into the wall mounting or connect the device to the

line power via the power supply.

Charging the battery in the charging station

1. Slide the battery into the charging station until it audibly clicks into place.

2. Connect the charging station supply to the line power.

Switching the device on/off

Switching on the device

Requirements:

• The device is disconnected from the patient.

• A fully charged battery is inserted in the device.

• The device is connected to the oxygen supply.

1. Brieﬂy press the On/Off button .

Switching off the device

1. Press and hold the On/Off button for > 2 s.

Performing a function check

Requirements:

• The device is disconnected from the patient.

• A charged battery is inserted in the device.

• The device input ﬁlter is inserted in the device.

• A patient hose system and a testing bag are available and ready for use.

• The protective cap has been removed from the end of the patient hose

system.

• A ﬁlled oxygen cylinder is available.

1. Check the device, plug, and cable for external damage.

If necessary: Replace components.

2. Brieﬂy press the On/Off button .

3. Brieﬂy press the menu button .

4. Select Function check in the start menu.

5. Follow the instructions in the function check.

Compressed gas

connection

Display

SD card Navigation knobs

button

Battery

Device

input ﬁlter

Connection for

ventilation hose

Line power/battery

status indicator

Alarm light

This document does not replace the instructions for use.

Complete information can be found in the instructions for use.

Battery status indicator

Device Battery Meaning

Battery status > 90%

Battery status approx. 60%-90%

Battery status approx. 40%-60%

Battery status approx. 10%-40%

Battery status < 10%

Battery is almost empty.

Battery is being charged.

Battery is defective, not inserted, or not at

the suitable temperature.

On/Off button

Line power/battery status indicator

Steady green light: Device connected to line power.

No light: Device in NVG mode.

Steady green light: The battery is full or is not being charged

because it is outside the charging

temperature range.

Flashing green light: The battery is being charged.

Steady red light: The battery is defective or not in the device.

No light: The device is operating on battery power and

not on line power or the device is in NVG mode.

Made in GermanySimply Professional

WM 68051b - 10/2015

WEINMANN Emergency

Medical Technology GmbH + Co. KG

Frohbösestraße 12 • 22525 Hamburg • GERMANY

T: +49 40 88 18 96-120 • F: +49 40 88 18 96-481

E: [email protected]

weinmann-emergency.de

MEDUMAT Standard2

Inhaltsverzeichnis

Andere Weinmann Medizinische Geräte Handbücher

Weinmann

Weinmann Homecare CPAP 20e Bedienungsanleitung

Weinmann

Weinmann ACCUVAC Pro Bedienungsanleitung

Weinmann

Weinmann ULM CASE Circulation Technisches Dokument

Weinmann

Weinmann SOMNOsmart 2 Bedienungsanleitung

Weinmann

Weinmann Prisma2Cloud WM 100 MW Bedienungsanleitung

Weinmann

Weinmann WM 13011 Handbuch

Weinmann

Weinmann SOMNObalance Gebrauchsanweisung

Weinmann

Weinmann MEDUMAT Standard2 Bedienungsanleitung

Weinmann

Weinmann MEDUCORE Standard2 Bedienungsanleitung

Weinmann

Weinmann JOYCE Full Face vented 40 hPa Bedienungsanleitung

Weinmann

Weinmann MEDUMAT Transport Bedienungsanleitung

Weinmann

Weinmann LIFE-BASE light XS Bedienungsanleitung

Weinmann

Weinmann Oxygen MODULE Einrichtungshandbuch

Weinmann

Weinmann ULM CASE I Bedienungsanleitung

Weinmann

Weinmann VENTIlogic BiLevel ST Betriebsanleitung

Weinmann

Weinmann Meducore Easy Bedienungsanleitung

Weinmann

Weinmann MEDUVENT Standard Bedienungsanleitung

Weinmann

Weinmann WM 24148 Bedienungs- und Montageanleitung

Weinmann

Weinmann WM 24042 Handbuch

Weinmann

Weinmann O2 Box Rescue compact Bedienungsanleitung

Weinmann

Weinmann JOYCEeasy Bedienungsanleitung

Weinmann

Weinmann homecare SOMNOsoft + WM 24600 Handbuch

Weinmann

Weinmann VENTImotion Series Betriebsanleitung

Weinmann

Weinmann VENTIlogic LS Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

FujiFilm

FujiFilm Sonart Betriebsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung