WEL SFT Bedienungsanleitung
SFT User Manual V1.5
Page 1 of 17
SFT
User Manual
SFT User Manual V1.5
Page 2 of 17
Contents
Release History ...............................................................................................................................................2
Case Contents .................................................................................................................................................3
LED States .......................................................................................................................................................3
Operation........................................................................................................................................................4
Cleaning Procedure.........................................................................................................................................4
Warnings.........................................................................................................................................................4
Android Software............................................................................................................................................5
Play Store Link ...........................................................................................................................................5
Installation.................................................................................................................................................5
Add License Key.........................................................................................................................................9
Change Minimum and Maximum Limits..................................................................................................10
PC Software ..................................................................................................................................................12
Requirements..........................................................................................................................................12
Installation...............................................................................................................................................12
Change Minimum and Maximum Limits..................................................................................................15
Fire SFT via a Hotkey................................................................................................................................16
Specifications................................................................................................................................................ 17
Warranty Statement and Terms and Conditions of Sale...............................................................................17
Contact Details:.............................................................................................................................................17
Release History
Version
Description
1.5
Improved PC installation instructions.
1.4
Added Add License Key
1.3
Added WEL Connect Hotkey.
1.2
Added cleaning procedure.
Added new LED states.
1.1
Converted to booklet
1.0
First Release
SFT User Manual V1.5
Page 3 of 17
Case Contents
LED States
LED State
Meaning
Green (single flash)
Valid test result.
Pink (single flash)
Below minimum g-force threshold.
Yellow (single flash)
Above maximum g-force threshold.
Red (single flash)
Invalid test result.
Blue (breathing)
Waiting to be connected to.
Blue (blinking)
Connected to device.
Red (solid)
Charging.
SFT PC Dongle
PC Software Flash Drive
Charge Cable
Test Block
SFT User Manual V1.5
Page 4 of 17
Operation
1. Place the SFT perpendicular to the fruit.
2. Press the trigger on the SFT.
•A beep and a green light indicates a valid measurement.
•Haptic feedback and a Red light indicates an invalid measurement.
3. Regularly clean the SFT tip
Cleaning Procedure
Clean the inside of the tip and probe regularly to prevent debris entering the gun mechanism.
1. Remove the nose tip and probe. Then clean both.
2. Re-install the tip. Then re-install the probe.
3. Fire the SFT twice to ensure the probe is seated correctly.
Warnings
•Avoid triggering the SFT while pointing it upwards, as debris may be dragged into the
mechanism.
•If the probe falls out. Reinsert the probe and fire the gun at least twice.
SFT User Manual V1.5
Page 5 of 17
Android Software
Play Store Link
https://play.google.com/store/apps/details?id=co
m.welnz.connect
Note a license is required to use the SFT with WEL
Connect.
Installation
1. Search for “WEL Connect”in the Play
Store or scan the QR code above.
2. Tap on “Install”
3. Tap on “Open”
SFT User Manual V1.5
Page 6 of 17
4. Allow access to location. (This is
required to connect to devices.)
5. Press the trigger on the SFT gun to turn
it on. Note: The SFT will be highlighted
in red after the trigger has been
pressed.
6. Tap on “CONNECT”
7. Complete calibration check, then tap on
“CLOSE”.
8. Tap on “START SESSION”.
SFT User Manual V1.5
Page 7 of 17
9. Fill out fields as required, then tap on
“START SESSION”.
10. Record measurements. To end the
session, press “back button.”
11. Once your data session is completed,
tap the icon or slide your finger
from the left side of the screen to the
right side to bring up the MENU.
12. Select “Data”.
SFT User Manual V1.5
Page 8 of 17
13. Select the data you want to email off.
Then tap on “EMAIL”. Note: Tap on the
recorded data to resume.
14. Allow access to photos and media. This
is required to generate the email
attachments.
15. Select your email client.
16. If using Gmail tap the “paper plane”
Button to send the data file.
SFT User Manual V1.5
Page 9 of 17
Add License Key
1. Tap on “Licenses”.
2. Tap on “SCAN DEVICE KEY”
3. Scan the QR code in the SFT rugged
case.
SFT User Manual V1.5
Page 10 of 17
Change Minimum and
Maximum Limits
On the SFT you can set minimum and maximum
limits for a valid measurement.
If the measurement is below the minimum value.
The SFT will flash pink.
If the measurement is above the maximum value
the SFT will flash yellow.
1. Tap on “CONNECT”
2. Tap on “CONFIG”
3. To edit the minimum and maximum
limits to what you want.
Tap on the “+” to increment the value.
Tap on the “-” to decrement the value.
Tap on the value to type the value in.
Inhaltsverzeichnis
Andere WEL Messgerät Handbücher
