Weltem AMERICOOL WPC-36003 Bedienungsanleitung

WPC-36003

Figure 1

Owner’s Manual

Speci ca ons

WPC-36003

Model No. Power Supply Ph-V-Hz Cooling Capacity Btu/h Power Con-

sump on Wa s

Rated Current

Amps

WPC-36003

3Phases - 460V - 60Hz

144,400 21.5kW 27A

Model No. Weight (Net / Gross)

Lbs(kg)

Ambient temperature

range °F( °C)

Dimensions

W x D x H - in. (mm)

WPC-36003 1168/1245lbs.

(530/565kg) 64~113(18~45) 34.3 x 75 x 71

(870 x 1904 x 1801 )

Model No. Indoor Air Flow CFM Refrigerant Type / oz(g)

WPC-36003 4000 R-410A / 278.7(7900)

Please read and save these instructions. Read carefully before attempting to assemble, install, oper-

ate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions

could result in personal injury and / or property damage! Retain instructions for future reference.

High Capacity Air Conditioner

(For Indoor & Outdoor)

AmeriCool Portable Air Condi oners are specialized for

“SPOT COOLING” where central cooling is imprac cal.

AmeriCool air condi oners can also be used in enclosed areas

just like conven onal air condi oners. Simple digital controller

and self-diagnos c func ons allow users to easily operate

the unit. Built-in Caster wheels enable users to move the

unit without any hassle. The unit can be installed in 5 minutes

and does not require any extra materials or cer  ed technician

for installa on.

AmeriCool Portable Air Condi oner, anywhere, everywhere.

Plug-and-Go!

A er unpacking the unit, carefully inspect unit for any damage that may have occurred during transit.

Check for any loose, missing, or damaged parts.

Descrip on

Unpacking

2 3

WPC-36003

Owner’s Manual

Specicaons (Connued)

Safety Devices

Compressor overload protector, An-freezing

thermister, Automac restart (Power interrupon),

Compressor me delay program, High pressure

switch

Features

Temperature control, Self-diagnosc funcon,

Oponal drain pump kit, Washable lters, °C display,

O-mer

PUMP-DOWN

The unit is integrated with “PUMP-DOWN”

funcon. PUMP-DOWN funcon keeps compressor

running for

certain me to protect compressor and other crucial

parts before the unit or compressor is turned o.

PUMP-DOWN funcon acvates,

- When the unit reaches target temperature

- In between cooling mode to heang mode

- In between cooling mode to Fan only operaon

The unit operates in this parcular way to protect the

internal parts.

During PUMP-DOWN cycle, the compressor and fans

will be keep operang even though user turns o the

unit or turns o the compressor.

Please do not forcefully switch o the unit or

compressor during PUMP-DOWN cycle. The unit or

compressor will turn o itself when it is safe for the

unit to do so.

General Safety Informaon

Please read this manual carefully for correct installaon and usage. Please read all safeguards.

1. Transport and store the unit in an upright posion only. Leave unit in an upright posion for

at least 3 hours before rst use.

2. Always place the unit on an even, level surface.

3. Ensure the unit is connected to a grounded power supply of the correct rang / capacity.

4. The unit will operate between 18°C (64°F) ~ 45°C(113°F) depending on the temperature

seng.

5. DO NOT use this unit for other purposes that is not described in this instrucon manual.

6. DO NOT lt the unit.

7. NEVER unplug the unit under operaon.

WPC-36003 Owner’s Manual

DO NOT use the unit in wet environments, such as a laundry room, to avoid

the risk of electrical shock.

10. DO NOT place any foreign objects on the unit.

11. DO NOT operate the unit with wet or damp hands.

12. DO NOT allow chemical substances to come into contact with the unit.

13. DO NOT operate the unit near ammable substances or vapors such as alcohols,

pescides, gasoline, etc.

14. DO NOT unplug to turn o the unit. Always use the power switch to start and to stop the unit.

15. Always turn o the unit and unplug it before cleaning, moving or performing maintenance.

16. AVOID using adapter plugs or extension cords. If extension cord or an adapter plug is

needed , ensure they are correctly rated for the applicaon. Consult a local qualied

electrician for proper setup. Any extension cord used with this device must be rated for

a minimum of 72A.(460V)

17. DO NOT unplug the unit by pulling on the electrical cord. Keep electrical cord away from

heat sources and always completely unroll the cord to avoid overheang. If the power cord

is damaged, contact a qualied service agent, qualied electrician, or similarly qualied

person for replacement.

DO NOT operate the unit in explosive or ammable environments.

DO NOT operate a unit with a damaged power cord.

18. The lters must be used with the product at all mes. When the lters are removed for

cleaning, always ensure that the unit has been turned o and unplugged from the

electrical outlet.

19. Regularly clean the lters to maintain eciency. If the lters are not cleaned regularly,

the units output performance and eciency will decrease.

20. DO NOT operate the unit with a damaged power cord or plug,

21. Only use in the upright posion on an even, at surface. There must not be any objects

or walls within 24 inches (60 cm) from the unit.

22. Halt the unit immediately if abnormal noise or odor is detected. Contact your local

service center or manufacturer.

23. Appliance is not to be operated by children or persons with reduced physical, sensory

or mental capabilies, or lack of experience and knowledge, unless they have been

given supervision or instrucon.

24. Children must be supervised not to play with appliance.

25. The unit must be installed in accordance with naonal wiring regulaons.

26. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent

or similarly qualied persons in order to avoid a hazard. .

4 5

WPC-36003

Owner’s Manual

Assembly (WPC-36003)

COMPONENT PARTS

Front and Right Side View

Controls

Hot Air Exhaust

Electrical Panel

Caster

Condensate

outlet

I BOLT

Cold Air Inlet

Cold Air Inlet Filter

Emergency Stop

Controls

Figure 2

Figure 3

Figure 4

Figure 5

Casters can be locked by

locking the break down

Handle

WPC-36003 Owner’s Manual

Figure 6

Figure 7

DUCT CONNECTIONS

Cool Air Out Duct(EVA)

Cool Air in Duct(EVA)

Hot Air Out Duct(COND)

Hot Air in Duct (COND)

Forkli

The Cool air duct connecons are labeled “AIR OUT”. The connecon size is

350Ø in diameter. Connect the exible air ducng as follows:

1. Aach the exible air ducng to the unit’s duct collars making sure

that air will not leak past the connecon collar by using appropriate

round exible ducng clamps.

2. Route the ducng as straight as possible to the space being

condioned avoiding excessive turns and pinches in the ducng.

3. Verify the terminaon points are not restricted meaning no

objects are directly in front of the terminaon.

The Return Air In duct connecon is labeled “AIR IN”.

The connecon size is 350Ø in diameter.

Follow the same procedures as the Cool Air Duct Connecons.

If you need outdoor air, please note that machine will read the

temperature of the outdoor air.

The Hot Air Out duct connecon is labeled “AIR OUT”

The connecon size is 450Øin diameter.

Follow the procedures as the cool air duct connecons

The Hot Air Out duct connecon is labeled “AIR IN”

The connecon size is 450Øin diameter.

Follow the procedures as the cool air duct connecons

If a forkli is needed to move the unit, put the foot of the forkli

to the forkli hole (shown in the picture: gure 8).

6 7

WPC-36003

Owner’s Manual

Installaon

MOVING THE UNIT

PLUGGING IN THE UNIT

Unlock the casters and push the unit using the side handles to a at, level surface and set the

caster brakes to the locked posion.

Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are pres-

ent, wipe o with a clean, dry cloth.

Check the power cord, plug and prongs for damage or excess play.

If any damage or excess play is found, contact a qualied repair technician or a qualied electri-

cian to perform replacement or repair of the power cord, plug or prongs.

NOTE: Make sure the AC outlet is free of dirt, dust, oil, water, or any other foreign material. The

unit is equipped with an approved NEMA plug conguraon. The appropriate outlet must

be used for each plug type.

WARNINGS REGARDING PROPER LOCATION FOR INSTALLATION

Do not use the unit in explosive environments or in areas where ammable

gas leakage may occur.

Do not use the unit in areas where it will be exposed to rain or water.

Do not use the unit in a corrosive atmosphere.

Do not use the unit above 18°C(64°F) ~ 45°C(113°F).

Do not install the unit on uneven or sloping surface. The unit may roll or

topple over even if the casters are set to the locked posion.

If the power cord or plug is damaged, repair should only be performed by

qualied electrical personnel.

Do not connect / disconnect the power cord or aempt to operate buons

with wet hands. This could result in electrical shock.

WPC-36003 Owner’s Manual

Operaon

CONTROL PANEL

1 2

3 4

Figure 10

1. POWER BUTTON :

Turns on/o the unit when the buon is pressed for 1 second.

2. BLOWER BUTTON :

Adjusts the fan speed from (Low) to (High) when the buon is pressed for 1 second.

NOTE: Some models only have one fan speed

3. SPOT/COOL BUTTON :

Acvates Spot Cooling mode when the buon is pressed for 1 second. Compressor can

be switched on/o

4. ROOM/COOL BUTTON :

Acvates Room Cooling mode when the buon is pressed for 1 second. Compressor can

be switched on/o

5. UP/DOWN BUTTON :

Sets target temperature in ROOM or SPOT COOL MODE.

6. ALARM :

The alarm indicator will ash when the unit detects abnormal operaon. The compressor

will stop aer the alarm and the system will stop aer 3 minutes of alarm unless there is

any acon taken to x the issue.

8 9

WPC-36003

Owner’s Manual

Operaon

CONTROL PANEL

9. EMERGENCY STOP :

Emergency stop buon immediately halts the operaon

1. Press the red buon – Unit stops

2. Inspect the unit.

3. Rotate the red buon clockwise to restart the unit

7. CURRENT TEMP :

Displays Current temperature

NOTE: Canadian version shows the temperature in Celsius.

8. TARGET TEMP :

Displays target temperature

OFF-TIMER : Press BLOWER Buon and SPOT/COOL Buon simultaneously for 2 seconds to

set o-mer. Press UP/DOWN Buon to set the mer. Aer you set o-mer, idle for 5 seconds to

save the o-mer seng. To cancel OFF-TIMER, set the mer to 0.

AUTO RESTART : If the unit turns o due to an electrical interrupon, the unit will automacally

restart when the power comes back on.

WPC-36003 Owner’s Manual

Maintenance

FILTER CLEANING (See Figures 11 and 12)

1. loosen up 6 bolts on the front lter guard.

2. Slide lter up and use a vacuum cleaner to remove the dust from the lter.

3. If the lter is heavily covered with dust and dirt, warm water and mild soap or neutral deter-

gent may be used to wash the lter. Do not use any other chemicals to clean lter, as they will

likely damage the lter.

4. Dry the lter in a shaded area before replacing it. Do not operate the unit without the lter

installed and the lter guard in the closed posion.

5. Replace the clean lter and close the lter guard.

– For your convenience, record the complete model number and product name (located on the

Product Idencaon Plate), the purchase date, purchase locaon, serial number, and war-

ranty period in the table below.

– Also, aach your purchase receipt as proof of purchase to this instrucon manual for future

reference.

– To ensure your product is covered by warranty, the complete faulty product along with your

original purchase receipt must be provided at the place of purchase.

Do not operate without the lter ed.

Do not operate the unit with a damaged cord or plug, aer the unit malfunc-

ons, or if the unit has been dropped or damaged.

– Loosen up 12 bolts on

the front ﬁlter guard.

– Slide ﬁlter up and use

a vacuum cleaner to remove

the dust from the ﬁlter.

– Remove dust from the ﬁlter

using a vacuum cleaner

hose aachment.

– If required wash the ﬁlter in

lukewarm water with a mild

detergent. Leave to dry in

a shaded area before

reinstalling.

Figure 11 – Removing Filters Figure 12 – Removal of Dust

NOTE: For eecve cooling clean the lter at least every 2 weeks.

10 11

WPC-36003

Owner’s Manual

Maintenance (Connued)

– To ensure your product is covered by warranty, the complete faulty product along with your

original purchase receipt must be provided at the place of purchase.

Product Portable Air Condioner

Model No.

Date of Purchase

Place of Purchase

Serial No.

Period of Warranty

Customer: Please read and keep this

manual for future reference and keep

sales receipt as proof of purchase.

SELF-DIAGNOSTIC CODES (See Table 1)

The alarm light is acvated if abnormal operaon occurs, and a code is displayed on the control

panel. The compressor and condenser fan motor will stop operang. The evaporator fan will con-

nue to run for 3 minutes. If the fault is reced within 3 minutes, the unit will resume opera-

on. If the fault persists for more than 3 minutes, the evaporator fan also stops. The fault must

be reced before the unit can resume normal operaon.

SELF-DIAGNOSTIC ALARM CODES

Alarm Display Problem Cause Correcve Acon

Frost prevenon

sensor and Abnormal

temperature sensor

value

• Indoor heat

exchanger tempera-

ture too low

• TH3 temperature

sensor has a loose

or broken connec-

on

• Do not use the air

condioner if ambient

temperature is lower

than 18°C (64°F)

• Contact a qualied

service agent

Table 1- Alarm Codes

Inhaltsverzeichnis

Andere Weltem Klimaanlage Handbücher

Weltem

Weltem AmeriCool WMC-2500 Bedienungsanleitung

Weltem

Weltem WPC-4000 Bedienungsanleitung

Weltem

Weltem WPC-3000N Bedienungsanleitung

Weltem

Weltem WPC-5000 Bedienungsanleitung

Weltem

Weltem WPC-3000 Bedienungsanleitung

Weltem

Weltem WPC-6000 Bedienungsanleitung

Weltem

Weltem WPW-4000 Bedienungsanleitung

Weltem

Weltem WSC-4000 Bedienungsanleitung

Weltem

Weltem WPW-4000 Bedienungsanleitung

Weltem

Weltem Americool HPC-3000 Bedienungsanleitung

Weltem

Weltem Americool HPC-3000 Bedienungsanleitung

Weltem

Weltem Icen WPC-7000 Bedienungsanleitung

Weltem

Weltem AmeriCool WPC-23000 Bedienungsanleitung

Weltem

Weltem Icen WPC-23000 Bedienungsanleitung

Weltem

Weltem AmeriCool WPC-18000 Bedienungsanleitung

Weltem

Weltem Icen WPC-9000 Bedienungsanleitung

Weltem

Weltem AMERICOOL Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung