Wenger Flex Kurzanleitung

Assembly Instructions and Owner’s Manual

Flex®Conductor’s Stand

ote: Please read and understand these instructions before assembling the parts.

ote: Remove all items from the shipping cartons and arrange them in a convenient location.

Refer to the illustrations on the following pages. If you need additional information,

contact the Wenger Corporation using the information below.

CONTENTS

©Wenger Corporation 2014 Printed in USA 12/14 Part #236C146-01

Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448

Questions? Call.....USA: 800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Parts ist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Attach Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Attach Desk ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

To Set the Desk Height . . . . . . . . . . . . . . . . . . . . . . . . .7

To Tilt the Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

To Rotate the Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

To Move the Flex Conductor’s Stand . . . . . . . . . . . . . . .8

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Flex Conductors Stand

with Polycarbonate Desk

Flex Conductors Stand

with High-Pressure Laminate Desk

SAFETY PRECAUTIONS

Make sure t at anyone working wit

t e Flex Conductor’s Stand as read

and understands t ese instructions.

!CAUTION

Failure to comply wit t e

Warnings and Cautions in t is

document can result in damage

to property or serious injury.

!CAUTION

Throughout this manual you may find cautions and warnings which are defined as follows.

• WAR I G means that failure to follow the instruction may result in serious injury or death.

• CAUTIO means that failure to follow the instruction may result in serious injury or damage to

property.

Read all of the safety instructions before assembling or using the Flex Conductor’s Stand.

IMPORTANT USER INFORMATION

GE ERAL

any form or by any means including graphic, electronic, or mechanical methods or photocopying,

recording, or information storage and retrieval systems without the written permission of the publisher,

unless it is for the purchaser's personal use.

Printed and bound in the United States of America.

The information in this manual is subject to change without notice and does not represent a commitment

on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any

errors that may appear in this manual.

In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for

direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this

manual.

The information in this document is not intended to cover all possible conditions and situations that might

occur. The end user must exercise caution and common sense when assembling or installing Wenger

Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-733-0393.

MA UFACTURER

The Flex Conductor’s Stand is manufactured by:

Wenger Corporation

555 Park Drive

Owatonna, MN 55060

1-800-4WENGER (493-6437) • 1-507-455-4100

www.wengercorp.com

ITE DED USE

•This product is intended for indoor use in normal ambient temperature and humidity conditions —

it must not be exposed to prolonged outside weather conditions.

•This product is intended to be assembled and used only as described in these instructions.

WARRA TY

This product is guaranteed free of defects in materials and workmanship for five full years from date

of shipment. A full warranty statement is available upon request.

REQUIRED TOOLS

PARTS LIST

Item Qty Description

11Hex Head Capscrew, 5/16-18 x 2”

21Washer, 3/8 ID x 1-1/4 OD

31Base

41Oval Mast

Desk Surface

(Polycarbonate or High Pressure aminate)

61Carriage Bolt, 5/16-18 x 5”

72Nylon Washer, .375 ID x 1.43 OD

81ock Nut, 5/16-18

91Desk ip (High Pressure aminate only)

10 4 Binding Post Screw, #8-32 x 3/8

(High Pressure aminate only)

11 4 Binding Post Barrel, #8-32

(High Pressure aminate only)

• 1/2" Socket or Open/Box End Wrench

• Flat Head Screwdriver

(for High-Pressure Laminate Desk Lip only)

BASE ASSEMBLY

Attach the Oval Mast to the Base:

1. Insert the Oval Mast (#4) into the oval shaped hole at the top of the Base (#3).

Push the Oval Mast until it is flush with the bottom of the Base.

2. Secure the Mast to the Base with one 5/16-18 x 2-inch Hex Head Capscrew (#1)

and 3/8 ID x 1-1/4 OD Washer (#2).

3. Using a 1/2" Socket or Open End Wrench, tighten the Capscrew.

To prevent possible t read damage, only tig ten to a maximum torque of 240 in-lb.

ASSEMBLY

Do not force t e Oval Mast into t e Base.

Damage to t e components could occur.

!CAUTION

Oval Mast

(#4)

Base

(#3)

5/16-18 x 2” Hex

Head Capscrew

(#1)

3/8 ID x 1-1/4 OD

Washer

(#2)

ATTACH DESK

Attach the Desk to the Base Assembly:

1. Position the Desk Surface (#5) over the Neck Mounting Tube at the top of the Base Assembly.

ote: The lever for the Dual ock Position Feature should be on the same side

as the Release Trigger.

2. Slide the 5/16-18 x 5” Carriage Bolt (#6) through the square side hole in the Desk Bracket,

.375 ID x 1.43 OD Nylon Washer (#7) and through the Neck Mounting Tube.

Another .375 ID x 1.43 OD Nylon Washer (#7) fits between the Neck Mounting Tube and

Desk Bracket before pushing the Carraige Bolt through the other side of the Desk Bracket.

3. Secure the Desk to the Base Assembly using a 5/16-18 ock Nut (#8) on the

5/16-18 x 5” Carriage Bolt as shown.

ASSEMBLY (continued)

Dual

Locking

Feature

Lock ut,

5/16-18

(#8)

.375 ID x 1.43 OD

ylon Washer

(#7) Square Hole

in Desk Bracket

Base

Assembly

Trigger

Lock

5/16-18 x 5”

Carriage Bolt

(#6)

eck

Mounting

Tube

Desk Surface

(#5)

.375 ID x 1.43 OD

ylon Washer

(#7)

Lock ut,

5/16-18

(#8)

5/16-18 x 5”

Carriage Bolt

(#6)

.375 ID x 1.43 OD

ylon Washer

(#7)

Polycarbonate Desk is shown.

Procedure for High-Pressure Laminate Desk is the same.

ATTACH DESK LIP (HIGH-PRESSURE LAMI ATE DESK OLY)

If attac ing t e Basket Accessory, consult t e Assembly Instructions 236C128 before proceding.

Attach the Desk ip to the Desk Surface:

1. Fit the Desk ip (#9) to fit on the underside of the Desk Surface.

Align the holes as shown.

2. Attach the Desk ip to the Desk Surface with four #8-32 x 3/8 Binding Post Screws (#10)

and #8-32 Binding Post Barrels (#11).

ASSEMBLY (continued)

#8-32 x 3/8

Binding Post Screw

(#10)

#8-32

Binding Post Barrel

(#11)

Desk Lip

(#9)

TOSET THE DESK HEIGHT:

1. Disengage the Release Trigger mechanism by grasping the support neck

under the desk and pulling the trigger while supporting the desk.

2. Raise or lower the desk to the desired position and release the trigger.

3. The desk will lock in the nearest locking position.

Desk height can be set in 2" increments.

TOTILT THE DESK:

Tilt the desk to the desired angle.

The desk is held in place by friction and should hold approximately 35 lbs

at any angle without rotating as a result of the load placed on the desk.

OPERATION

To prevent t e desk from falling w ile

adjusting t e eig t, old on to t e desk

w en t e Release Lever is disengaged.

!CAUTION

1. Clean the Flex Conductor’s Stand with a mild detergent.

Avoid using harsh or abrasive cleaning products.

2. Never apply oil or any lubricant to the height adjustment tube.

3. Periodically check fasteners to ensure that they have not loosened during use.

MAINTENANCE

TOROTATE THE DESK:

1. The desk has lock positions at the 0 and 180 degree

positions.

2. Press upward on the ocking ever under the center

of the desk and simultaneously rotate the desk.

The desk automatically locks when rotated to the

180 or 0 degree position.

TOMOVE THE FLEX CO DUCTOR STA D:

1. Tilt the stand towards the wheels at the front of the boomerang shaped

cast iron base.

2. Push or pull stand assembly by grasping the upright mast just under

the desk.

OPERATION

Inhaltsverzeichnis

Andere Wenger Inneneinrichtung Handbücher

Wenger

Wenger Gearboss Customizable Wood Lockers Bedienungsanleitung

Wenger

Wenger StageTek Chair Stop Bedienungsanleitung

Wenger

Wenger Ensemble Stücklistenhandbuch

Wenger

Wenger UltraStor Series Bedienungsanleitung

Wenger

Wenger StageTek Guardrail Acceossory Bedienungsanleitung

Wenger

Wenger Stringed Instrument Storage Cabinet Programmierhandbuch

Wenger

Wenger StageTek Roll-A-Deck Bedienungsanleitung

Wenger

Wenger Bookcases Bedienungsanleitung

Wenger

Wenger Diva Bedienungsanleitung

Wenger

Wenger Fixed Media Cabinets Bedienungsanleitung

Wenger

Wenger Tourmaster Choral Riser Bedienungsanleitung

Wenger

Wenger Violin Bedienungsanleitung

Wenger

Wenger Corner Cabinet Bedienungsanleitung

Wenger

Wenger Nota Stücklistenhandbuch

Wenger

Wenger 5-light 30" Studio Makeup Station Bedienungsanleitung

Wenger

Wenger teacherTAXI Bedienungsanleitung

Wenger

Wenger AcoustiCabinet Bedienungsanleitung

Wenger

Wenger UltraStor Cover Panel Bedienungsanleitung

Wenger

Wenger OnBoard 210A018 Bedienungsanleitung

Wenger

Wenger GearBoss Shelving Drawer Accessory Montage- und Bedienungsanleitung

Wenger

Wenger GearBoss AirPro Locker Bedienungsanleitung

Wenger

Wenger 029A105 Bedienungsanleitung

Wenger

Wenger UltraStor Bedienungsanleitung

Wenger

Wenger Conductor’s Chair Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

Furinno

Furinno 18089 Bedienungsanleitung

Munchkin

Munchkin Push to Close MK0001 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Anthro

Anthro GT03 Series Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung