Westermo BRD-355A Bedienungsanleitung
www.westermo.com
BRD-355A & BRD-355B
Industrial ADSL/VDSL Routers
26623-2232
3
6623-2232
General information
Legal information
The contents of this document are provided “as is”. Except as required by applicable law,
no warranties of any kind, either express or implied, including, but not limited to, the
implied warranties of merchantability and fitness for a particular purpose, are made in
relation to the accuracy and reliability or contents of this document. Westermo reserves
the right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Westermo be responsible for any loss of data or income or
any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at www.westermo.com
46623-2232
Safety and Regulations
Warning signs are provided to prevent personal injuries and/or damages to the product.
The following levels are used:
Level of warning Description Consequence
personal injury
Consequence
material damage
WARNING
Indicates a potentially
hazardous situation
Possible death or
major injury
Major damage to the
product
CAUTION
Indicates a potentially
hazardous situation
Minor or moderate
injury
Moderate damage to
the product
NOTICE
Provides information
in order to avoid
misuse of the
product, confusion or
misunderstanding
No personal injury Minor damage to the
product
NOTE
Used for highlighting
general, but important
information
No personal injury Minor damage to the
product
5
6623-2232
Before installation:
Read this manual completely and gather all information on the product. Make sure that
you understand it fully. Check that your application does not exceed the safe operating
specifications for this product.
WARNING - SAFETY DURING INSTALLATION
The product must be installed by qualified service personnel
and built in to an apparatus cabinet or similar, where access is
restricted to service personnel only.
During installation, ensure a protective earthing conductor is
first connected to the protective earthing terminal (only valid for
metallic housings). Westermo recommends a cross-sectional area
of at least 4 mm2.
If the product does not have a protective earthing terminal, then
the DIN-rail must be connected to protective earth. Upon removal
of the product, ensure that the protective earthing conductor, or
the connection to earth via the DIN-rail, is disconnected last.
WARNING - PROTECTIVE FUSE
It must be possible to disconnect manually from the power supply.
Ensure compliance to national installation regulations. Replacing
the internal fuse must only be performed by Westermo qualified
personell.
WARNING - HAZARDOUS VOLTAGE
Do not open an energized product. Hazardous voltage may occur
when connected to a power supply.
WARNING - POWER SUPPLY CONNECTION
There are safety regulations on which power sources that shall
be used in conjunction with the product. Refer to Interface
Specifications.
66623-2232
WARNING - REDUCE THE RISK OF FIRE
To reduce the risk of fire, use only telecommunication line cords
with a cable diameter of AWG 26 or larger. Regarding power
cable dimensions, see Interface Specifications.
CAUTION - ELECTROSTATIC DISCHARGE (ESD)
Prevent electrostatic discharge damages to internal electronic
parts by discharging your body to a grounding point (e.g. use a
wrist strap).
CAUTION - CABLE TEMPERATURE RATING FOR
FIELD TERMINAL WIRES
There may be a requirement on the minimum temperature rating
of the cable to be connected to the field wiring terminals, see
Interface Specifications.
7
6623-2232
Care recommendations
Follow the care recommendations below to maintain full operation of product and to
fulfill the warranty obligations:
• Do not drop, knock or shake the product. Rough handling above the specification
may cause damage to internal circuit boards.
• Use a dry or slightly water-damp cloth to clean the product. Do not use harsh
chemicals, cleaning solvents or strong detergents.
• Do not paint the product. Paint can clog the product and prevent proper operation.
If the product is used in a manner not according to specification, the protection provided
by the equipment may be impaired.
If the product is not working properly, contact the place of purchase, nearest Westermo
distributor office or Westermo technical support.
Product disposal
This symbol means that the product shall not be treated as
unsorted municipal waste when disposing of it. It needs to
be handed over to an applicable collection point for recy-
cling electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help to reduce hazardous substances and prevent potential
negative consequences to both environment and human
health, which could be caused by inappropriate disposal.
86623-2232
Agency approvals and standards compliance
Type Approval / Compliance
EMC EN 55032, Multimedia equipment, Emission Requirements
EN 55035, Multimedia equipment, Immunity Requirements
Safety EN 62368-1, Safety Communication Technology
Simplified EU declaration of conformity
Hereby, Westermo declares that the product is in compliance with applicable EU
directives. The full EU declaration of conformity and other detailed information is
available at the respective product page at www.westermo.com/support/product-
support.
EN 62368-1
Notice:
This product has been tested and found compliant to EN 62368-1, Safety for
Communication Technology. In accordance with the definitions of the standard, this
product shall be handled by skilled personell. Energy source classifications are according
to following:
Electrical energy source Power port ES1
Serial port ES1
Ethernet port ES1
Power source Power port PS3
Thermal energy source Enclosure TS1
Mechanical energy source Enclosure MS1
Radiation energy source SFP Not applicable
9
6623-2232
Type tests and environmental conditions
Phenomena Test Description Test levels
ESD EN 61000-4-2 Enclosure contact ± 6 kV (crit B)
Enclosure air ± 8 kV (crit A)
Radiated RF immunity IEC 61000-4-3 Enclosure 20 V/m (crit A)
(80 – 6000 MHz)
Fast transient EN 61000-4-4 DC power ports ± 2 kV (crit B)
Ethernet ports ± 2 kV (crit B)
Serial port ± 2 kV (crit B)
xDSL ports ± 2 kV (crit B)
Surge EN 61000-4-5 DC power ports ± 2 kV (crit B), 42 Ω
± 500 V (crit A), 12 Ω
Ethernet ports ± 4 kV (crit B), (shielded cable)
xDSL ports ± 4 kV (crit B)
RF conducted EN 61000-4-6 DC power ports 10 V/m, (crit A), (0.15 – 80 MHz)
Ethernet ports 10 V/m, (crit A), (0.15 – 80 MHz)
10 V/m, (crit B), (0.15 – 80 MHz)
xDSL ports 10 V/m (crit A), (0.15 – 80 MHz)
10 V/m (crit B), (0.15 – 80 MHz)
Radiated emission CISPR 16-2-3 Enclosure EN 61000-6-3
Conducted emission CISPR 16-2-1 DC power ports
EN 61000-6-3
CISPR 32 Ethernet ports
xDSL port
Dialectric strenght EN 62368-1
IEEE 802.3
Power port to all other ports
1.5 kVrms, 50 Hz, 1 minSignal port to all other ports
xDSL port to all other ports
Temperature EN 60068-2-1
EN 60068-2-2
Operating –25 to +70°C (–13 to +158°F)
Storage & Transport –40 to +85°C (–40 to +185°F)
Humidity EN 60068-2-30 Operating 0 to 90% relative humidity non
condensing.
Storage & Transport 0 to 90% relative humidity non
condensing.
Altitude Operating 2000 m / 70 kPa
Service life Operating 10 years
Dimension W x H x D 53 x 103 x 97 mm
(2.08 x 4.05 x 3.81 in)
Weight 0.40 kg
Degree of protection IEC 529 Enclosure IP 40
Cooling Convection
Mounting Horizontal on 35 mm DIN-rail
10 6623-2232
Description
Remote access removes boundaries, eliminates the need for time consuming site visits
and provides a network infrastructure suitable for today's “always-on” society. The BRD-
355 is an industrially designed xDSL (ADSL/VDSL2) broadband router built to cope with
harsh environments and the characteristics of industrial applications. The unit supports a
wide range of xDSL-standards and has support for long lines.
Most devices today comes equipped with an Ethernet port for communications,
therefore the BRD-355 has a built-in two port Ethernet switch. For legacy connectivity
the unit also features one RS-232-port to provide multiple connection possibilities for
both new and legacy replacement installations. Designed to be installed on a DIN-rail
all connectors and LEDs have been positioned in the front of the unit, facing the user
for easy access and fast status feedback. With wide power input range, the unit can be
powered from 10 to 60 VDC and has low power consumption.
The cybersecurity features of the BRD-355 prevent unauthorized access and secure
the communication for Internet-enabled applications. The easy to use firewall filters
incoming traffic, allowing only approved packets to pass through. To inter-connect units
with each other securely over the Internet multiple VPN technologies are supported,
including IPsec and OpenVPN.
Upgrading legacy solutions to become IP-enabled can prove both costly and tedious
therefore the BRD-355 includes a wide feature set for various legacy applications
including both modem replacement methods as well as serial to Ethernet conversion.
If there are applications that require extra attention Westermo's extensive experience
from over 35 years within industrial data communications and over 5 years of industrial
xDSL expertise will be available to assist you.
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Westermo Netzwerk-Router Handbücher
Westermo
Westermo Viper-12 Series Bedienungsanleitung
Westermo
Westermo DDW-02-B1 Bedienungsanleitung
Westermo
Westermo Lynx 5600 Series Bedienungsanleitung
Westermo
Westermo SDI-550 Bedienungsanleitung
Westermo
Westermo SDW-500 Bedienungsanleitung
Westermo
Westermo Lynx L106-F2G Bedienungsanleitung
Westermo
Westermo MR-210 Bedienungsanleitung
Westermo
Westermo DR-250 Bedienungsanleitung
Westermo
Westermo Ibex-330 Series Bedienungsanleitung
Westermo
Westermo Viper 008 Bedienungsanleitung
Westermo
Westermo MRD-405 Bedienungsanleitung
Westermo
Westermo Viper 008 Bedienungsanleitung
Westermo
Westermo RFI-219-T3G Bedienungsanleitung
Westermo
Westermo MRD-415 Bedienungsanleitung
Westermo
Westermo SDW-550 E-mark Bedienungsanleitung
Westermo
Westermo BRD-355 Bedienungsanleitung
Westermo
Westermo MRD-315 Bedienungsanleitung
Westermo
Westermo Lynx DSS Bedienungsanleitung
Westermo
Westermo MRD-315 Bedienungsanleitung
Westermo
Westermo Viper 408 Bedienungsanleitung
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise