Westermo Lynx L206-F2G-EX Bedienungsanleitung

www.westermo.com

Lynx L206-F2G-EX

Industrial Ethernet 6-port Switch

26643-22001

6643-22001

General information

Legal information

The contents of this document are provided “as is”. Except as required by applicable law,

no warranties of any kind are made in relation to the accuracy and reliability or contents

of this document, either expressed or implied, including but not limited to the implied

warranties of merchantability and fitness for a particular purpose. Westermo reserves

the right to revise this document or withdraw it at any time without prior notice.

Under no circumstances shall Westermo be responsible for any loss of data or income or

any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at www.westermo.com

Software tools

Related software tools are available at www.westermo.com/support/software-tools.

License and copyright for included Free/Libre Open Source Software

This product includes software developed by third parties, including Free/Libre Open

Source Software (FLOSS). The specific license terms and copyright associated with the

software are included in each software package respectively. Please visit the product web

page for more information.

Upon request, the applicable source code will be provided. A nominal fee may be

charged to cover shipping and media. Please direct any source code request to your nor-

mal sales or support channel.

WeOS Management Guide

This product runs WeOS (Westermo Operation System). Instructions for quick start,

configuration, factory reset and use of USB port are found in the WeOS Management

Guide at www.westermo.com.

46643-22001

Safety and Regulations

Warning signs are provided to prevent personal injuries and/or damages to the product.

The following levels are used:

Level of warning Description Consequence

personal injury

Consequence

material damage

WARNING

Indicates a potentially

hazardous situation

Possible death or

major injury

Major damage to the

product

CAUTION

Indicates a potentially

hazardous situation

Minor or moderate

injury

Moderate damage to

the product

NOTICE

Provides information

in order to avoid

misuse of the

product, confusion or

misunderstanding

No personal injury Minor damage to the

product

NOTE

Used for highlighting

general, but important

information

No personal injury Minor damage to the

product

6643-22001

Before installation:

Read this manual completely and gather all information on the product. Make sure that

you understand it fully. Check that your application does not exceed the safe operating

specifications for this product.

WARNING - SAFETY DURING INSTALLATION

The product must be installed by qualified service personnel

and built in to an apparatus cabinet or similar, where access is

restricted to service personnel only.

During installation, ensure a protective earthing conductor is

first connected to the protective earthing terminal (only valid for

metallic housings). Westermo recommends a cross-sectional area

of at least 4 mm2.

If the product does not have a protective earthing terminal, then

the DINrail must be connected to protective earth. Upon removal

of the product, ensure that the protective earthing conductor, or

the connection to earth via the DIN-rail, is disconnected last.

WARNING - PROTECTIVE FUSE

It must be possible to disconnect manually from the power supply.

Ensure compliance to national installation regulations. Replacing

the internal fuse must only be performed by Westermo qualified

personell.

WARNING - HAZARDOUS VOLTAGE

Do not open an energized product. Hazardous voltage may occur

when connected to a power supply.

WARNING - POWER SUPPLY CONNECTION

There are safety regulations on which power sources that shall

be used in conjunction with the product. Refer to Interface

Specifications.

66643-22001

WARNING - REDUCE THE RISK OF FIRE

To reduce the risk of fire, use only telecommunication line cords

with a cable diameter of AWG 26 or larger. Regarding power

cable dimensions, see Interface Specifications.

CAUTION - CORROSIVE GASES

If the product is placed in a corrosive environment, it is important

that all unused connector sockets are protected with a suitable

plug, in order to avoid corrosion attacks on the gold plated

connector pins.

CAUTION - ELECTROSTATIC DISCHARGE (ESD)

Prevent electrostatic discharge damages to internal electronic

parts by discharging your body to a grounding point (e.g. use a

wrist strap).

CAUTION - CLASS 1 LASER PRODUCT

Do not look directly into a fibre optical port or any connected

fibre, although the product is designed to meet the Class 1 Laser

regulations and complies with 21 CFR 1040.10 and 1040.11.

CAUTION - HANDLING OF SFP TRANSCEIVERS

SFP transceivers are supplied with plugs to avoid contamination

inside the optical port. They are very sensitive to dust and dirt. If

the fibre is disconnected from the product, the protective plugs

on the transmitter/receiver must be connected. The protective

plugs must be kept on during transportation. The fibre optics

cables must be handled the same way.

6643-22001

CAUTION - HOT SURFACE

Be aware of that the surface of this product may become hot.

When it is operated at high temperatures, the external surface

may exceed Touch Temperature Limit according to the product's

relevant electrical safety standard.

CAUTION - CABLE TEMPERATURE RATING FOR

FIELD TERMINAL WIRES

There may be a requirement on the minimum temperature rating

of the cable to be connected to the field wiring terminals, see

Interface Specifications.

Product disposal

This symbol means that the product shall not be treated

as unsorted municipal waste when disposing of it. It needs

to be handed over to an applicable collection point for

recycling electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will

help to reduce hazardous substances and prevent potential

negative consequences to both environment and human

health, which could be caused by inappropriate disposal.

Care recommendations

Follow the care recommendations below to maintain full operation of product and to

fulfill the warranty obligations:

• Do not drop, knock or shake the product. Rough handling above the specification

may cause damage to internal circuit boards.

• Use a dry or slightly water-damp cloth to clean the product. Do not use harsh

chemicals, cleaning solvents or strong detergents.

• Do not paint the product. Paint can clog the product and prevent proper operation.

If the product is used in a manner not according to specification, the protection provided

by the equipment may be impaired.

If the product is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo technical support.

86643-22001

ATEX certification

ATEX certification number

Baseefa12ATEX0119X

Standards

EN 60079-0, EN 60079-15

Certification code

Ex nA IIC T3 Gc (-40°C ≤ Ta ≤ +70°C)

ATEX code

II 3G

Specific Conditions of Use

The equipment must be installed in an area of not more than pollution degree 2 in

accordance with IEC/EN 60664-1, and in an enclosure that provides a minimum degree of

protection of at least IP54 and complies with the relevant requirements of EN 60079-0

and EN 60079-15.

All external connections to the equipment and, where applicable, the SFP modules must

not be inserted or removed unless either the area in which the equipment is installed is

known to be non-hazardous, or the circuits connected have been de-energized.

The network cables once installed must be properly fixated by the use of cable ties or

similar to reduce the risk of accidently withdrawing the plugs.

Equipment input parameters

Power Connector: +DC1, +DC2 & -COM

Working Voltage Range = 24 V to 48 VDC.

I/O Connector: ‘Status +’ & ‘Status -’ and ‘Digital in +’ and ‘Digital in -’

Maximum I/P Voltage = 60 VDC.

6643-22001

SFP option approved transceivers

SFP Transceivers, 100 Mbit

1100-0131 MLC2, Multimode, LC-Connector, 2 km, 1310 nm

1100-0132 SLC20, Singlemode, LC-Connector, 20 km, 1310 nm

1100-0133 SLC40, Singlemode, LC-Connector, 40 km, 1310 nm

1100-0134 SLC80, Singlemode, LC-Connector, 80 km, 1550 nm

1100-0140 SLC120, Singlemode, LC-Connector, 120 km, 1550 nm

BiDi Transceivers, 100 Mbit

1100-0145 SLC15-BiDi-A, Singlemode, BiDi, 20 km, 1310 nm TX, 1550 nm RX

1100-0146 SLC15-BiDi-B, Singlemode, BiDi, 20 km, 1550 nm TX, 1310 nm RX

1100-0152 MLC2-BiDi-A, Multimode, BiDi, 2 km, 1310 nm TX, 1550 nm RX

1100-0153 MLC2-BiDi-B, Multimode, BiDi, 2 km, 1550 nm TX, 1310 nm RX

SFP Transceivers, 1 Gbit

1100-0144 GMLC550-SX, Multimode, LC-Connector, 550 m, 850 nm, SX

1100-0147 GMLC2-SX+, Multimode, LC-Connector, 2 km, 1310 nm, SX+

1100-0141 GSLC10-LX, Singlemode, LC-Connector, 10 km, 1310 nm, LX

1100-0142 GSLC50-XD, Singlemode, LC-Connector, 50 km, 1550 nm, XD

1100-0143 GSLC80-ZX, Singlemode, LC-Connector, 80 km, 1550 nm, ZX

1100-0171 GSLC110-EZX, Singlemode, LC-Connector, 110 km, 1550 nm, EZX

BiDi Transceiver, 1 Gbit

1100-0156 GSLC20-BiDi-A, Singlemode, BiDi, 20 km, 1310 nm TX, 1490 nm RX

1100-0157 GSLC20-BiDi-B, Singlemode, BiDi, 20 km, 1490 nm TX, 1310 nm RX

Copper Transceiver, 1 Gbit

1100-0148 GC100, Copper, RJ45, 100 m, 1000BaseT

10 6643-22001

ATEX-Zertifizierung

ATEX-Zulassungsnummer

Baseefa12ATEX0119X

Standards

EN 60079-0, EN 60079-15

Zertifizierungscode

Ex nA IIC T3 Gc (-40°C ≤ Ta ≤ +70°C)

ATEX-Code

II 3G

Spezifische Einsatzbedingungen

Die Geräte müssen in einem Bereich welcher einem maximalen Verschmutzungsgrad der

Stufe 2 gemäß IEC/EN 60664-1 entspricht und in einem Gehäuse, das einen Schutzgrad

von mindestens IP54 bietet und die relevanten Anforderungen von N 60079-0 und EN

60079-15 erfüllt, installiert werden.

Alle äußeren Anschlüsse des Gerätes und auch die SFP-Module dürfen nur dann verbun-

den oder getrennt werden, wenn entweder der Bereich, in dem das Gerät installiert ist,

nachweislich ungefährlich ist, oder die verbundenen Stromkreise spannungsfrei sind.

Die Netzwerkkabel müssen nach der Installation mithilfe von Kabelbindern oder ähnli-

chem Material ordnungsgemäß befestigt werden, um ein versehentliches Abziehen der

Stecker zu verhindern.

Eingangsparameter der Geräte

Stromversorgung: +DC1, +DC2 & -COM

Betriebsspannungsbereich = 24 V to 48 VDC.

I/O-Anschluss: ‘Status +’ & ‘Status -’ und ‘Digital in +’ und ‘Digital in -’

Maximale I/P-Spannung = 60 VDC.

Inhaltsverzeichnis

Andere Westermo Schalten Handbücher

Westermo

Westermo Viper 108 Bedienungsanleitung

Westermo

Westermo RedFox RFI-119-F4G-T7G Bedienungsanleitung

Westermo

Westermo SDW-500 Bedienungsanleitung

Westermo

Westermo Lynx DSS L206-S2-EX Bedienungsanleitung

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Bedienungsanleitung

Westermo

Westermo Lynx L206-F2G Bedienungsanleitung

Westermo

Westermo Lynx DSS L108 Bedienungsanleitung

Westermo

Westermo Viper-112A-P8-HV Bedienungsanleitung

Westermo

Westermo Viper-12-PoE Bedienungsanleitung

Westermo

Westermo RedFox 5528 Series Bedienungsanleitung

Westermo

Westermo RedFox-5528-E-T28G-LV Bedienungsanleitung

Westermo

Westermo Viper-208-TBN Series Bedienungsanleitung

Westermo

Westermo Viper 12A Series Bedienungsanleitung

Westermo

Westermo Lynx L210-F2G-EX Bedienungsanleitung

Westermo

Westermo SD-300 Series Bedienungsanleitung

Westermo

Westermo Viper 008 Bedienungsanleitung

Westermo

Westermo Viper TBN Series Bedienungsanleitung

Westermo

Westermo MRI-128-F4G-PSE Series Bedienungsanleitung

Westermo

Westermo Lynx DSS L205-S1-EX Bedienungsanleitung

Westermo

Westermo Lynx-3510-F2G-P8G-LV Bedienungsanleitung

Westermo

Westermo RedFox Industrial EX Series Bedienungsanleitung

Westermo

Westermo RFIR-127-F4G-T7G-DC Bedienungsanleitung

Westermo

Westermo RFI-211-T3G Bedienungsanleitung

Westermo

Westermo L105-S1 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch