Westermo RFIR-127-F4G-T7G-DC Bedienungsanleitung

Industrial Routing Switch

www.westermo.com

©Westermo Teleindustri AB

User Guide

6641-22810

RedFox

Industrial Rack

SERIES

WeOS

Status-

Status+

Digital In-

Digital In+

26641-22810

Legal information

The contents of this document are provided “as is”. Except as required by applicable

law, no warranties of any kind, either express or implied, including, but not limited to,

the implied warranties of merchantability and fitness for a particular purpose, are made

in relation to the accuracy and reliability or contents of this document. Westermo

reserves the right to revise this document or withdraw it at any time without prior

notice.

Under no circumstances shall Westermo be responsible for any loss of data or income

or any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

http://www.westermo.com

Software tools

Related software tools are available in the folder software tools under

technical support on the Westermo website.

6641-22810

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure

that you understand it fully. Check that your application does not exceed the safe

operating specifications for this unit.

This unit should only be installed by qualified personnel. This unit should be built-in to

an apparatus cabinet, or similar, where access is restricted to service personnel only.

The power supply wiring must be sufficiently fused, and if necessary it must be

possible to disconnect manually from the power supply. Ensure compliance to

national installation regulations.

This unit uses convection cooling. To avoid obstructing the airflow around the unit,

follow the spacing recommendations (see Cooling section).

Before powering-up, a protective earthing conductor must be connected to the

protective earthing terminal and have a cross-sectional area of at least 1.5 mm².

Before mounting, using or removing this unit:

Warning! Do not open connected unit. Hazardous voltage may occur within this

unit when connected to power supply. Prevent access to hazardous voltage by

disconnecting the unit from power supply.

Caution: Double pole/neutral fusing (AC models only)

Class 1 Laser Product. Do not look directly into fibre optical fibre port or

any connected fibre, although this unit is designed to meet the Class 1 Laser

regulations. Complies with 21 CFR 1040.10 and 1040.11.

Caution: To reduce the risk of fire, use only No. 26 (e.g. 24 AWG) UL listed or

CSA certified Telecommunication Line Cord.

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfil

the warranty obligations.

This unit must not be operating with removed covers or lids.

Do not attempt to disassemble the unit. There are no user serviceable parts inside.

Do not drop, knock or shake the unit, rough handling above the specification may cause

damage to internal circuit boards.

Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.

Do not paint the unit. Paint can clog the unit and prevent proper operation.

Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit is not

waterproof. Keep the unit within the specified humidity levels.

Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical

part may be damaged.

If the unit is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo Tech support.

Fibre connectors are supplied with plugs to avoid contamination inside the optical port.

As soon as no optical fibre is mounted on the connector, e.g. for storage, service or

transportation, the plug should be applied.

6641-22810

Note. Fibre Optic Handling

Fibre optic equipment needs special treatment. It is very sensitive to dust and dirt. If the

fibre will be disconnected from the unit the protective hood on the transmitter/receiver

must be connected. The protective hood must be kept on during transportation. The

fibre optic cable must also be handle the same way.

If these recommendations are not followed the warranty might be jeopardized.

Cleaning of the optical connectors

In the event of contamination, the optical connectors should only be cleaned by the use

of recommended cleaning fluids and correct cleaning equipment.

Recommended cleaning fluids:

• Methyl-, ethyl-, isopropyl- or isobutyl-alcohol

• Hexane

• Naphtha

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

6641-22810

Agency approvals and standards compliance

Art.no Model Type Approval/compliance

3641-4020

3641-4030

3641-4005

3641-4015

3641-4025

3641-4035

RFIR-127-F4G-T7G-DC

RFIR-127-F4G-T7G-AC

RFIR-219-F4G-T7G-DC

RFIR-219-F4G-T7G-AC

RFIR-227-F4G-T7G-DC

RFIR-227-F4G-T7G-AC

EMC EN 50121-4, Railway applications –

Electromagnetic compatibility – Emission and

immunity of the signalling and telecommunications

apparatus

EN 55022, Information technology equipment –

Radio disturbance characteristics – Limits and

methods of measurement

EN 55024, Information technology equipment –

Immunity characteristics Limits and methods of

measurement

EN 61000-6-1, Electromagnetic compatibility –

Immunity for residential environments

EN 61000-6-2, Electromagnetic compatibility –

Immunity for industrial environments

EN 61000-6-4, Electromagnetic compatibility –

Emission for industrial environments

IEC 62236-4, Railway signalling and

telecommunications apparatus

Safety UL/IEC/EN 60950-1, IT equipment

Marine DNV GL rules for classification – Ships and

offshore units

DNV GL rules for classification

Type Temperature Humidity Vibration EMC Enclosure

RFIR-xxx-F4G-T7G-AC C B A A A/IP40

RFIR-xxx-F4G-T7G-DC D B A B A/IP40

FCC Part 15.105

Notice:

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

EN 55022 Notice: This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

66641-22810

Safety control drawing

Position Direction/

description Input/Output values

Status+ IO / Status + Uin = 60 VDC max

Status-- IO / Status – Iin = 80 mA max

Digital In+ IO / Digital in + Uin = 60 VDC max

Digital In- IO / Digital in – Iin = 2.9 mA max

Position Direction/

description Output values

1 In / VBUS

U = 5 VDC max

I = 100 mA max

2 In/out / D–

3 In/out / D+

4 Not connected

5 Functional earth

Degree of protection: IP 40

Ambient temperature: –40 °C to +70 °C (DC), –40 °C to +55 °C (AC)

Position Direction/

description Input/output values

1 In/out / BI_DA+

Per port:

U = ± 1 V (4V/us)

I = ± 20 mA

Data rate:

10/100/1000 Mbit/s

2 In/out / BI_DA–

3 In/out / BI_DB+

4 In/out / BI_DC+

5In/out / BI_DC–

6 In/out / BI_DB–

7 In/out / BI_DD+

8 In/out / BI_DD–

Shield Functional earth

Galvanically isolated via signal transformers and

capacitively isolated to GND/Functional earth

through a 2kV 1000pF capacitor.

See user manual for proven transient protection.

Status-

Status+

Digital In-

Digital In+

Position Direction/

description Output values

1 Out / VBUS

Uout = 5 VDC max

Iout = 500 mA max

2 In/out / D–

3 In/out / D+

4 GND

Shield Functional earth

Direction/

description Input values

In / +DC1

Uin = (16 – 60) VDC

Iin = 2.0 A@16 VDC*

PIn = 32 W@16 VDC*

In / +DC2

In / COM

DC Power supply AC Power supply

Direction/

description Input values

In / P

Uin = (100–240) VAC,

50–60 Hz

Iin = 360 mA@100 VAC**

In / N

In / NC

In /

+DC1

+DC2

COM

* RFIR-227-T7G-F4G-DC

** RFIR-227-T7G-F4G-AC

6641-22810

1000 Base-X1000 Base-T

Safety control drawing

Position Direction* / description Input/output values

Rx In / Receive port Max 5 dBm

Tx Out / Transmit port

Position Direction* / description Input/output values

1 In/out / BI_DA+

Per port:

U = ± 1 V (4V/us)

I = ± 20 mA

Data rate:

100/1000 Mbit/s

2 In/out / BI_DA–

3 In/out / BI_DB+

4 In/out / BI_DC+

5 In/out / BI_DC–

6 In/out / BI_DB–

7 In/out / BI_DD+

8 In/out / BI_DD–

Shield Functional earth

Galvanically isolated via signal transformers and capacitively

isolated to functional earth through a 2kV 1000pF

capacitor. See user manual for proven transient protection.

* Direction relative this unit!

10/100 Base-TX

Position Direction* / description Input/output values

1 In/out / TD+

Per port:

U = ± 1 V (4V/us)

I = ± 20 mA

Data rate:

10/100 Mbit/s

2 In/out / TD–

3 In/out / RD+

4 Not connected

5Not connected

6 In/out / RD–

7 Not connected

8 Not connected

Shield Functional earth

Galvanically isolated via signal transformers and capacitively

isolated to functional earth through a 2kV 1000pF

capacitor.

See user manual for proven transient protection.

6641-22810

Declaration of Conformity

Westermo Teleindustri AB

Declaration of Conformity

Org.nr/

Postadress/Postal address

Tel.

Telefax

Postgiro

Bankgiro

Corp. identity number

Registered office

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna

Sweden Int+46 16428000 Int+46 16428001

The manufacturer Westermo Teleindustri AB

SE-640 40 Stora Sundby, Sweden

Herewith declares that the product(s)

Type of product Models

Industrial Ethernet Switch

for 19 inch Rack mounting

RFIR-x19-F4G-T7G-DC, RFIR-x27-F4G-T7G-DC

RFIR-x19-F4G-T7G-AC, RFIR-x27-F4G-T7G-AC

is in conformity with the following EU directive(s).

No Short name

2014/30/EU Electromagnetic Compatibility (EMC)

2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic equipment

(RoHS)

2014/35/EU Low Voltage Directive (LVD)

1 Model Differences: x = 1 or 2 and indicates Software Class

References of standards applied for this EU declaration of conformity.

No Title Issue

EN 50121-4 Railway applications – Electromagnetic compatibility – Emission and

immunity of the signalling and telecommunications apparatus

2015

EN 55022 Information technology equipment – Radio disturbance characteristics –

Limits and methods of measurement

2010

EN 55024 Information technology equipment – Immunity characteristics

Limits and methods of measurement

2010

EN 61000-6-1 Electromagnetic compatibility – Immunity for residential environments 2007

EN 61000-6-2 Electromagnetic compatibility – Immunity for industrial environments 2005

EN 61000-6-4 Electromagnetic compatibility – Emission for industrial environments 2007

+A1:2011

EN 50581 Technical documentation for the assessment of electrical and electronic

products with respect to the restriction of hazardous substances

2012

EN 60950-1 Information technology equipment - Safety - Part 1: General

requirements

2006

+A11: 2009

+A1: 2010

+A12: 2011

+A2: 2013

The last two digits of the year in which the CE marking was affixed: 16

Pierre Öberg

Technical Manager

March 2016

6641-22810

Type tests and environmental conditions

Phenomena Test Description Test levels

ESD EN 61000-4-2 Enclosure contact ± 6 kV

Enclosure air ± 8 kV

RF field AM modulated IEC 61000-4-3 Enclosure 20 V/m 80% AM (1 kHz), 80 – 2700 MHz

10 V/m 80% AM, 1kHz sine, 2700 – 6000 MHz

Fast transient EN 61000-4-4 Signal ports ± 2 kV

Power ports ± 2 kV

Surge EN 61000-4-5 Signal ports ± 2 kV line to earth, ± 1 kV line to line

Power ports ± 2 kV line to earth, ± 2 kV line to line

(AC models)

± 2 kV line to earth, ± 1 kV line to line

(DC models)

RF conducted EN 61000-4-6 Signal ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz

Power ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz

Power frequency

magnetic field

EN 61000-4-8 Enclosure 300 A/m 0, 16.7, 50, 60 Hz

Pulse magnetic field EN 61000-4-9 Enclosure 300 A/m

Radiated emission CISPR 16-2-3 Enclosure Class A

ANSI C63.4

(FCC part 15)

Enclosure Class B, 30 – 6500 MHz

Conducted emission EN 55022 AC and DC power

ports

Telecommunication

ports Class B

Class B

FCC part 15 AC and DC power

ports

Class B

Dielectric strength EN 60950 Signal port to other

isolated ports

1.5 kVrms 50 Hz 1 min

Power port to other

isolated ports

1.5 kVrms 50 Hz 1 min

Temperature EN 60068-2-1

EN 60068-2-2

Operating -40 to +70ºC (DC models)

-40 to +55ºC (AC models)

Storage & Transport -40 to +85ºC (all models)

Maximum surface

temperature

135 °C (temperature class T4)

Humidity EN 60068-2-30 Operating 5 to 95% relative humidity

Storage & Transport 5 to 95% relative humidity

Altitude Operating 2 000 m / 70 kPa

Service life Operating 10 years

Vibration IEC 60068-2-6 Operating 7.5 mm, 5 – 8 Hz

2 g, 8 – 500 Hz

(19" rack mounting according to IEC 60297,

DIN 41494)

Shock IEC 60068-2-27 Operating 15 g, 11 ms

(19" rack mounting according to IEC 60297,

DIN 41494)

Enclosure UL 94 Aluminium / Zink Flammability class V-0 (all models)

6641-22810

Description

The RFIR (RedFox Industrial Rack) is a high performance industrial Ethernet switch

designed for high network traffic applications. Various port configurations are available

that can be further customized with SFP transceivers. RFIR is powered by the Westermo

WeOS network operating system.

RFIR is designed for 19” cabinet according to ETSI standard making it suitable for use

in control room networks as well as for cabi¬nets installed along railway trackside or

maritime installations. RFIR is designed to run efficiently from an AC or DC power supply,

the unit is also equipped with configurable I/O fault contact that make it ideal for easy

installation and monitoring in industrial applications.

RedFox Industrial Rack models

Westermo

article number

Denomination Description

3641-4020 RFIR-127-F4G-T7G-DC

16 x 10/100 Mbit/s, Ethernet TX, RJ-45

7 x 10/100/1000 Mbit/s, Ethernet TX, RJ-45