Westermo Lynx SERIES Bedienungsanleitung

Industrial Ethernet

8-port Switch

www.westermo.com

REV.B 6640-2001 2008.08 Mälartryck AB, Eskilstuna, Sweden

©Westermo Teleindustri AB

User Guide

6640-2001

Lynx

SERIES

26640-2001

Legal information

The contents of this document are provided “as is”. Except as required by applicable

law, no warranties of any kind, either express or implied, including, but not limited to,

the implied warranties of merchantability and fitness for a particular purpose, are made

in relation to the accuracy and reliability or contents of this document. Westermo

reserves the right to revise this document or withdraw it at any time without prior

notice.

Under no circumstances shall Westermo be responsible for any loss of data or income

or any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

http://www.westermo.com

6640-2001

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure

that you understand it fully. Check that your application does not exceed the safe

operating specifications for this unit.

This unit should only be installed by qualified personnel.

This unit should be built-in to an apparatus cabinet, or similar, where access is

restricted to service personnel only.

The power supply wiring must be sufficiently fused, and if necessary it must be

possible to disconnect manually from the power supply. Ensure compliance to

national installation regulations.

This unit uses convection cooling. To avoid obstructing the airflow around the unit,

follow the spacing recommendations (see Cooling section).

Before mounting, using or removing this unit:

Prevent access to hazardous voltage by disconnecting the unit from power supply.

Warning! Do not open connected unit. Hazardous voltage may occur within this

unit when connected to power supply.

Class 1 Laser Product

Do not look directly into fibre optical fibre port or any connected fibre although

this unit is designed to meet the Class 1 Laser regulations.

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfil

the warranty obligations.

This unit must not be operating with removed covers or lids.

Do not attempt to disassemble the unit. There are no user serviceable parts inside.

Do not drop, knock or shake the unit, rough handling above the specification may cause

damage to internal circuit boards.

Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.

Do not paint the unit. Paint can clog the unit and prevent proper operation.

Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit is not water-

proof. Keep the unit within the specified humidity levels.

Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical

part may be damaged.

If the unit is not working properly, contact the place of purchase, nearest Westermo dis-

tributor office or Westermo Tech support.

Fibre connectors are supplied with plugs to avoid contamination inside the optical port.

As long as no optical fibre is mounted on the connector, e.g. for storage, service or

transportation, should the plug be applied.

46640-2001

Note. Fibre Optic Handling

Fibre optic equipment needs special treatment. It is very sensitive to dust and dirt. If

the fibre will be disconnected from the modem the protective hood on the transmitter/

receiver must be connected. The protective hood must be kept on during transportation.

The fibre optic cable must also be handle the same way.

If this recommendation not will be followed it can jeopardise the warranty.

Cleaning of the optical connectors

In the event of contamination, the optical connectors should be cleaned by the use of

forced nitrogen and some kind of cleaning stick.

Recommended cleaning fluids:

• Methyl-, ethyl-, isopropyl- or isobutyl-alcohol

• Hexane

• Naphtha

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified

conditions.

Agency approvals and standards compliance

Type Approval / Compliance

EMC EN 61000-6-2, Immunity industrial environments

EN 55024, Immunity IT equipment

EN 61000-6-3, Emission residential environments

FCC part 15 Class B

EN 50121-4, Railway signalling and telecommunications apparatus

IEC 62236-4, Railway signalling and telecommunications apparatus

Safety EN 60950-1, IT equipment

FCC Part 15.105 Notice: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a partic-

ular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

… Reorient or relocate the receiving antenna

… Increase the separation between the equipment and receiver

… Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

… Consult the dealer or an experienced radio/TV technician for help.

6640-2001

Declaration of Conformity

Westermo OnTime AS, Corp. identity number 981 567 560

Gladsvei 20, 0489 Oslo, Norway www.ontimenet.com

Tel +47 22090303 Fax +47 22090310 e-mail: co[email protected]

CE Certificate of Conformity

Westermo OnTime AS declares that the listed products conform to the Council Directives and standards:

73/23/EEG Low Voltage Directive (LVD)

89/336/EEG Electromagnetic Compatibility (EMC –directive)

EN 61000-2

EN 61000-6-2

EN 61000-6-4

EN 50121-4

EN 50121-3-2 (except conducted measurement values)

EN 50155-1

EN 50155-2 all temperature classes

EN 50155-3

EN 50155-4 MTBF >180.000 hrs at 55°C (MIL2.17)

EN 50155-5 chap. 5.1:OnTime Quality Manual after ISO9001:2000 principles

chap. 5.3: not conforming according to ISO 9002

EN 50155-6

EN 50155-7 chap. 7.7: With protective coating

chap. 7.9: With wall mounting brackets

EN 50155-8 chap. 8.2: not conforming

EN 50155-9 defined documents available for customer after signing of Non-Disclosure-

Agreement

EN 50155-10 chap. 10.2.11: With wall mounting brackets

IEC 60945, 8.7 Sinusoidal vibration

IEC 60068-2-6 test Fc

IEC 60068-2-64 tests Fh

IEC 60068-2-27 tests Ea

IEC 60068-2-29 tests Eb

IEC 60068-2-30 test Db

IEC 68-2-2 test Bd Dry Heat

Type of Equipment: Industrial Ethernet Switches

Models: U208, R208, T208 all versions,

Lynx series

Reference: U/R/T200 Operator Manual, Lynx Operator Manual

U/R/T200 Install Guide, Lynx Install Guide

Øyvind Holmeide, sign.

Managing Director

March 27th, 2006

66640-2001

Type tests and environmental conditions

Environmental phenomena Basic standard Description Test levels

EMC

ESD EN 61000-4-2 Enclosure contact ± 6 kV

Enclosure air ± 8 kV

RF field AM modulated IEC 61000-4-3 Enclosure 20 V/m 80% AM (1 kHz), 80 – 2 000 MHz

RF field 900 MHz ENV 50204 Enclosure 20 V/m pulse modulated 200 Hz, 900 ± 5 MHz

Fast transient EN 61000-4-4 Signal ports ± 2 kV

Power ports ± 2 kV

Surge EN 61000-4-5 Signal ports ± 2 kV line to earth, ± 2 kV potential difference

Power ports ± 2 kV line to earth, ± 2 kV line to line

RF conducted EN 61000-4-6 Signal ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz

Power ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz

Power frequency magnetic field EN 61000-4-8 Enclosure 1000 A/m, 50 Hz

Pulse magnetic field EN 61000-4-9 Enclosure 300 A/m

Voltage dips and interruption EN 61000-4-29 DC power ports Voltage interruption - 3 x 30 s within 5 minutes:

19V to 0 V & 62.4 V to 0V

Power supply variation - 3 x 1 minute

30% increase and 25% reduction

Radiated emission EN 55022 Enclosure Class B

FCC part 15 Class B

IEC 60945 Complying with the limit line

Conducted emission EN 55022 Signal ports Class B

EN 55022 DC power ports Class B

IEC 60945 Complying with the limit line

Dielectric strength EN 60950-1 Signal port to

other isolated

ports

1.5 kVrms 50 Hz 1 min

Power port to

other isolated

ports

1.5 kVrms 50 Hz 1 min

Environmental

Temperature Operating –40 to +70ºC

Storage &

Transport

–50 to + 85ºC

Humidity Operating 5 to 95% relative humidity

Storage &

Transport

5 to 95% relative humidity

Altitude Operating 2 000 m / 70 kPa

Service life Operating 10 year

Vibration IEC 60068-2-6 Operating 1 mm, 3 – 13.2 Hz

0.7 g, 13.2 – 100 Hz

1.5 g, 5.5 – 30 Hz

0.42 mm, 30 – 50 Hz

4.2 g, 50 – 500 Hz

IEC 60068-2-64 Operating 0.23 g, 3 – 2000 Hz

Shock IEC 60068-2-27 Operating All directions: 2 g, 11 ms

Z-axis: 30 g, 11 ms

Bump IEC 60068-2-29 Operating 2 g, 11ms

Packaging

Enclosure UL 94 Aluminium Flammability class V-1

Dimension W x H x D

With connectors

52.5 x 100 x 101 mm

52.5 x 119 x 101 mm

Weight 0.6 kg

Degree of protection IEC 529 Enclosure IP 40

Cooling Convection

Mounting Horizontal on 35 mm DIN-rail

6640-2001

Description

Lynx is a range of switches consisting of three different function levels and four different

type approvals, giving you the ability to select the perfect switch for your application

providing optimum functionality at the best value.

Our unique FRNT (Fast Recovery of Network Topology) technology is the fastest proto-

col on the market to re-configure a network in the event of any failure of a link or hard-

ware. That is why the Lynx-series is used in safety critical applications such as tunnels,

traffic signal control and railway systems.

Installations in harsh environments and places with heavy electrical interference demand

the use of a reliable media. The Lynx-series provides a number of solutions using fibre

optic transceivers. Multi- or singlemode transceivers can be used to build point-to-point

or redundant ring networks with ranges up to 120 km between each switch. Our BIDI

transceiver, which transmits and receives data on a single fibre can be used in applications

where the number of fibre cores is limited.

Real-time properties are implemented in the Lynx-series in order to achieve determinism

for real time critical applications. The Lynx-switches supports QoS (Quality of Service)

with four priority queues and strict priority scheduling as well as HoL (Head of Line

Blocking Prevention). All to assure that the data network is deterministic.

86640-2001

Interface specifications

Power

Operating voltage 19 to 60 VDC

Rated current 146 mA @ 24 VDC

80 mA @ 48 VDC

Rated frequency DC

Inrush current, I2t 49·10-4 A2s @ 48 VDC

Startup current* 250 mA @ 24 VDC

Polarity Reverse polarity protected

Redundant power input Yes

Isolation to All other

Connection Detachable screw terminal

Connector size 0.2 – 2.5 mm2 (AWG 24 – 12)

Shielded cable Not required

* External supply current capability for proper startup

Ethernet TX

Electrical specification IEEE std 802.3. 2000 Edition

Data rate 10 Mbit/s, 100 Mbit/s, manual or auto

Duplex Full or half, manual or auto

Circuit type SELV

Transmission range 150 m, according to long cable specification

Isolation to Power

Connection TX connectors: RJ-45 shielded, auto MDI/MDI-X

Shielded cable Not required, except when installed in Railway applications as

signalling and telecommunications apparatus and located close

to rails.

Conductive housing Isolated to all other circuits

Number of ports 6

6640-2001

Ethernet SFP pluggable connections (FX or TX)

Electrical specification IEEE std 802.3. 2000 Edition

Data rate 100 Mbit/s, 1000 Mbit/s manual or auto

Duplex Full or half, manual or auto

Circuit type SELV

Transmission range Depending on tranceiver

Isolation to Power

Connection TX connectors: RJ-45 shielded, auto

MDI/MDI-X FX connectors: LC

Shielded cable Not required

Conductive housing Isolated to all other circuits

Number of ports 1 or 2

Status relay

Contact resistance 25 Ω

Isolation to 1500 VDC

Connection Detachable screw terminal

Connector size 0.2 – 2.5 mm2 (AWG 24 – 12)

10 6640-2001

FX (Fibre) SM-LC80 SM-LC40 SM-LC15 MM-LC2

Fibre connector LC duplex LC duplex LC duplex LC duplex

Fibre type Singlemode

9/125 mm

Singlemode

9/125 mm

Singlemode

9/125 mm

Multimode,

62.5/125 and

50/125 mm

Wavelength 1550 nm 1310 nm 1310 nm 1310 nm

Transmitter

Output optical power min/max

–5/0 dBm** –5/0 dBm** –15/–8 dBm** –20/–14 dBm*

Receiver

Input sensitivity, max

–34 dBm –34 dBm –31 dBm –31 dBm

Receiver

Input optical power, max

–5 dBm*** –3 dBm*** –8 dBm –8 dBm

Optical power budget,

worst-case

29 dB 29 dB 16 dB 11 dB

Transceiver type Small Form Factor Pluggable (SFP)

Multi-Sourcing Agreement (MSA) compliant

Laser class Class 1, IEC 825-1 Accessible Emission Limit (AEL)

Optical Power Budget

The allowed link length is calculated from the optical power budget (OPB), the available optical

power for a fibre-optic link, and the attenuation of the fibre, comprising losses due to in-line

connectors, splices, optical switches and a margin for link ageing (typical 1.5 dB for 1300 nm).

The worst-case optical power budget (OPB) in dB for a fibre-optic link is determined by the differ-

ence between the transmitter’s output optical power (min) and the receiver input sensitivity (max).

FX (Fibre) Bi-di

LC-60

Bi-di

LC-40

Bi-di

LC-20

Bi-di

MM LC-2

Fibre connector LC Simplex LC Simplex LC Simplex LC Simplex

Fibre type Singlemode

9/125 μm

Singlemode

9/125 μm

Singlemode

9/125 μm

Multimode

62.5/125 and

50/125 μm

Wavelength nm, connector 1

Wavelength nm, connector 2

Tx 1310, rx

1550 Tx 1550,

rx 1310

Tx 1310, rx

1550 Tx 1550,

rx 1310

Tx1310, rx

1550 TX

1550, rx 1310

Tx 1310, rx

1550 Tx 1550,

rx 1310

Transmitter

Output optical power min/max

–5/0 dBm ** –8/0 dBm ** -10/0 dBm ** –10/–8 dBm *

Receiver

Input sensitivity, max

–34 dBm –34 dBm –28 dBm –28 dBm

Receiver

Input optical power, max

0 dBm*** 0 dBm*** 0 dBm –0 dBm

Optical power budget,

worst-case

29 dB 26 dB 18 dB 18 dB

Transceiver type Small Form Factor Pluggable (SFP)

Multi-Sourcing Agreement (MSA) compliant

Laser class Class 1, IEC 825-1 Accessible Emission Limit (AEL)

* Output power is power coupled into a 62.5/125 mm multimode fibre

** Output power is power coupled into a 9/125 mm singlemode fibre

*** The optical power should be reduced by at least 5 dB (SM-LC80 and Bi-di LC-60) or 3dB (SM-LC-40

and Bi-di LC-40) between the optical output and input.

Andere Handbücher für Lynx SERIES

Inhaltsverzeichnis

Andere Westermo Schalten Handbücher

Westermo

Westermo Viper TBN Series Bedienungsanleitung

Westermo

Westermo RedFox 5528 Series Bedienungsanleitung

Westermo

Westermo MRI-128-F4G-PSE Series Bedienungsanleitung

Westermo

Westermo Viper-TBN Series Bedienungsanleitung

Westermo

Westermo SD-300 Series Bedienungsanleitung

Westermo

Westermo Lynx L110 F2G EX Bedienungsanleitung

Westermo

Westermo SDW-500 Bedienungsanleitung

Westermo

Westermo MDI-110 Series Bedienungsanleitung

Westermo

Westermo Lynx DSS L205-S1-EX Bedienungsanleitung

Westermo

Westermo PMI-110-F2G Bedienungsanleitung

Westermo

Westermo Viper-112A-P8-HV Bedienungsanleitung

Westermo

Westermo RedFox 5728 Series Bedienungsanleitung

Westermo

Westermo RedFox RFI-119-F4G-T7G Bedienungsanleitung

Westermo

Westermo RedFox 7528 Series Bedienungsanleitung

Westermo

Westermo L110-F2G Bedienungsanleitung

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Bedienungsanleitung

Westermo

Westermo Viper 12A Series Bedienungsanleitung

Westermo

Westermo Viper 108 Bedienungsanleitung

Westermo

Westermo RedFox 5528 Series Bedienungsanleitung

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Bedienungsanleitung

Westermo

Westermo Lynx DSS L206-S2-EX Bedienungsanleitung

Westermo

Westermo RedFox Industrial EX Series Bedienungsanleitung

Westermo

Westermo Lynx DSS L206-S2 Bedienungsanleitung

Westermo

Westermo RedFox-5528-E-T28G-LV Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung