Westermo Lynx DSS L206-S2 Bedienungsanleitung

www.westermo.com

Lynx DSS

L106-S2/L206-S2

Industrial Ethernet

6-port Device Server Switch

WeOS

26643-2240

6643-2240

General information

Legal information

The contents of this document are provided “as is”. Except as required by applicable law,

no warranties of any kind, either express or implied, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose, are made in

relation to the accuracy and reliability or contents of this document. Westermo reserves

the right to revise this document or withdraw it at any time without prior notice.

Under no circumstances shall Westermo be responsible for any loss of data or income or

any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following address:

www.westermo.com

Software tools

Related software tools are available in the folder software tools under technical support

on the Westermo website.

License and copyright for included Free/Libre Open Source Software

This product includes software developed by third parties, including Free/Libre Open

Source Software (FLOSS). The specific license terms and copyright associated with the

software are included in each software package respectively. Please visit the product web

page for more information.

Upon request, the applicable source code will be provided. A nominal fee may be charged

to cover shipping and media. Please direct any source code request to your normal sales

or support channel.

WeOS Management Guide

This product runs WeOS (Westermo Operation System). Instructions for quick start,

configuration, factory reset and use of USB port are found in the WeOS Management

Guide at www.westermo.com.

46643-2240

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure that

you understand it fully. Check that your application does not exceed the safe operating

specifications for this unit.

Warning - Hazardous voltage

The product must be installed by qualified service personnel

and built in to an apparatus cabinet or similar, where access is

restricted to service personnel only.

Before powering up, a protective earthing conductor must

be connected to the protective earthing terminal. Westermo

recommends a cross-sectional area of at least 4 mm2 on the

protective earthing conductor.

Do not open a connected product. Hazardous voltage may occur

when connected to a power supply.

Disconnect all network connectors and cable distribution system

connectors, including power supply, before disconnecting the

protective earthing terminal.

Warning - Protective fuse

The power supply wiring must be sufficiently fused. It must be

possible to disconnect manually from the power supply. Ensure

compliance to national installation regulations. Refer to the user

guide for detailed information.

Replacing the internal fuse must only be performed by Westermo

qualified personell.

Warning - Reduce the risk of fire

To reduce the risk of fire, use only no. AWG 26 or larger

telecommunication line cord.

6643-2240

Caution - Electrostatic discharge (ESD)

Prevent damage to internal electronic parts from electrostatic

discharge (ESD) by discharging your body to a grounding point

(e.g. use of a wrist strap).

Caution - Hot surface

Be aware of that the surface of this product may become hot.

When it is operated at high temperatures, the external surface

may exceed Touch Temperature Limit according to EN/IEC/UL

60950-1.

Westermo’s products are fanless and use convection cooling.

To avoid obstructing the airflow around the product, follow the

spacing recommendations.

Caution - Wiring

Ensure that the temperature rating of the cable is sufficient for the

application before connecting to the field wiring terminals.

Note

This unit can be connected to two different power sources.

66643-2240

Product disposal

This symbol means that the product shall not be treated

as unsorted municipal waste when disposing of it. It needs

to be handed over to an applicable collection point for

recycling electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will

help to reduce hazardous substances and prevent potential

negative consequences to both environment and human

health, which could be caused by inappropriate disposal.

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfill

the warranty obligations:

• Do not drop, knock or shake the unit. Rough handling above the specification may

cause damage to internal circuit boards.

• Do not use harsh chemicals, cleaning solvents or strong detergents to clean the

unit.

• Do not paint the product. Paint can clog the product and prevent proper operation.

If the unit is not working properly, contact the place of purchase, nearest Westermo

distributor office or Westermo technical support.

6643-2240

Agency approvals and standards compliance

Type Approval / Compliance

EMC EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrial environments

EN 61000-6-3, Emission residential environments

EN 61000-6-4, Emission industrial environments

EN 50121-4, Railway signalling and telecommunications apparatus

IEC 62236-4, Railway signalling and telecommunications apparatus

Safety UL/IEC/EN 60950-1, IT equipment

Marine DNV GL rules for classification – Ships and offshore units

FCC Part 15.105

Notice:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

… Reorient or relocate the receiving antenna

… Increase the separation between the equipment and receiver

… Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

… Consult the dealer or an experienced radio/TV technician for help.

Corrosive

environment

Notice:

This product has been successfully tested in a corrosion test according to IEC 60068-

2-60, method 3. This means that the product meets the requirements to be placed in an

environment classified as ISA-S71.04 class G3.

Simplified EU declaration of conformity

Hereby, Westermo declares that the equipment is in compliance with EU directives. The

full EU declaration of conformity and other detailed information are available at the

respective product page at www.westermo.com. .

Caution - Corrosive gases

If the product is placed in a corrosive environment, it is important

that all unused connector sockets are protected with a suitable

plug, in order to avoid corrosion attacks on the gold plated

connector pins.

86643-2240

Type tests and environmental conditions

Environmental phenomena Basic standard Description Test levels

Electrostatic discharge EN 61000-4-2 Enclosure Contact: ±6 kV

Air: ±8 kV

Fast transients EN 61000-4-4 Power port ±2 kV

Ethernet

Status out/Digital in

Serial ports

Enclosure

Surge EN 61000-4-5 Power port L-L: ±0.5 kV, 2 Ω, 18 μF

L-E: ±2 kV, 42 Ω, 0.5 μF

L-L: ±1 kV, 42 Ω, 0.5 μF

L-E: ±2 kV, 12 Ω, 9 μF

L-L: ±1 kV, 12 Ω, 9 μF

Ethernet L-E: ±2 kV, 2Ω, 0.5 μF

Status out/Digital in L-E: ±2 kV, 42 Ω, 0.5 μF

L-L: ±1 kV, 42 Ω, 0.5 μF

RS-232 L-E: ±2 kV, 2 Ω, 0.5 μF

RS-422/485 L-E: ±2 kV, 42 Ω, 0.5 μF

Power frequency magnetic field EN 61000-4-8 Enclosure 300 A/m; 0, 16.7, 60 Hz

1000 A/m; 50 Hz

Pulsed magnetic field EN 61000-4-9 Enclosure 300 A/m

Radiated RF immunity EN 61000-4-3 Enclosure 20 V/m @ (80 – 2700) MHz

10 V/m @ (2700 – 6000) MHz

1 kHz sine, 80% AM

Conducted RF immunity EN 61000-4-6 Power port 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz

Ethernet

Status out/Digital in

Serial ports

Earth port

Radiated RF emission CISPR 16-2-3

ANSI C63.4

(FCC Part 15)

Enclosure Class B / DNV bridge

Conducted RF emission CISPR 16-2-1

ANSI C63.4

(FCC Part 15b)

Power port Class B / DNV bridge

Ethernet Class B

Dielectric strength EN 60950-1 Power port to all

other ports

1.5 kVrms, 50 Hz, 1 min

Ethernet ports to all

other ports

RS-232 port to all

other ports

RS-422/485 port to all

other ports

6643-2240

Environmental

Temperatures EN 60068-2-1

EN 60068-2-2

Operating –40 to +70°C (–40 to +158°F)*

Storage and transport –50 to +85°C (–58 to +185°F)

Humidity EN 60068-2-30 Operating 5 to 95 % relative humidity

Storage and transport 5 to 95 % relative humidity

Altitude Operating 2 000 m / 70 kPa

MTBF MIL-C217F2,

Parts count

Ground Benign, 25°C

(77°F)

593 000 hours

Service life Operating 10 year

Vibration IEC 60068-2-6

(sine)

Operating 3 – 13.2 Hz: 1mm

13.2 – 100 Hz: 0.7 g

5.5 – 30 Hz: 1.5 g

30 – 50 Hz: 0.42 mm

50 – 500 Hz: 4.2 g**

IEC 60068-2-64

(random)

5 – 20 Hz: 2 m²/s³,

20 – 2000 Hz: – 3 dB/oct

Shock IEC 60068-2-27 Operating 30 g, 11 ms

100 g, 6 ms**

Bump IEC 60068-2-27 Operating 10 g, 11 ms

Packaging

Enclosure EN 60950-1 Zinc Fire enclosure

Dimension W x H x D

With connectors

52.5 x 100 x 101 mm

52.5 x 119 x 101 mm

Weight 0.7 kg

Degree of protection EN 60529 Enclosure IP 40

Cooling Convection

* Refer to “Safety” section in User Guide.

** Might require Ethernet cables to be fastened close to the unit.

Description

L106-S2/L206-S2 is an Industrial switch and device server made for harsh environments.

WeOS is the operating system of L106-S2/L206-S2 enabling the unit to operate in two

functional levels. The switch can be used in either 10 or 100 Mbit networks.

Lynx DSS L106-S2/L206-S2 has two serial ports, one that supports RS-232 and the other

configurable for RS-232/422/485 as well as serial protocols for interconnection with

legacy equipment.

Our unique FRNT (Fast Recovery of Network Topology) technology is the fastest

protocol on the market to re-configure a network in the event of any link or hardware

failure. That is why our equipement are used in safety critical applications such as tunnels,

traffic signal control and railway systems.

10 6643-2240

Interface specifications

Power

Operating voltage Rated: 24 to 48 VDC

Operating: 19 to 60 VDC

Rated current 150 mA (300 mA) @ 24 VDC (with 500 mA USB load)

80 mA (150 mA) @ 48 VDC (with 500 mA USB load)

Rated frequency DC

Inrush current, I2t 22.7·10-3 A2s @ 48 VDC

Startup current* 2 x Rated current

Polarity Reverse polarity protected

Redundant power input Ye s

Isolation to All other

Connection Detachable screw terminal

Conductor cross section 0.2 – 2.5 mm2(AWG 24 – 12)

Stripping length cable 7 mm

Tightening torque, terminal screw 0.5-0.6 Nm

Tightening torque, screw flange 0.3 Nm

Shielded cable Not required

* External supply current capability for proper start-up

Ethernet TX

Electrical specification IEEE std 802.3. 2005 Edition

Data rate 10 Mbit/s, 100 Mbit/s, manual or auto

Duplex Full or half, manual or auto

Circuit type TNV-1

Transmission range Up to 150 m with CAT5e cable or better*

Isolation to All other

Connection RJ-45, auto MDI/MDI-X

Cabling Shielded CAT5e or better is recommended

Conductive housing Ye s

Number of ports 4

* Refer to Safety section.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Westermo Schalten Handbücher

Westermo

Westermo Lynx SERIES Bedienungsanleitung

Westermo

Westermo SDW-500 Bedienungsanleitung

Westermo

Westermo Viper-12-PoE Bedienungsanleitung

Westermo

Westermo MRI-128-F4G-PSE Series Bedienungsanleitung

Westermo

Westermo Viper TBN Series Bedienungsanleitung

Westermo

Westermo U200 series Bedienungsanleitung

Westermo

Westermo Viper-112A-P8-HV Bedienungsanleitung

Westermo

Westermo SDW-500 Bedienungsanleitung

Westermo

Westermo RedFox 5528 Series Bedienungsanleitung

Westermo

Westermo Viper-TBN Series Bedienungsanleitung

Westermo

Westermo RedFox-5728-F4G-T24G-LV Bedienungsanleitung

Westermo

Westermo Lynx-3510-F2G-P8G-LV Bedienungsanleitung

Westermo

Westermo Lynx L206-F2G-EX Bedienungsanleitung

Westermo

Westermo MRI-128-F4G Series Bedienungsanleitung

Westermo

Westermo Lynx DSS L108-F2G-S2 EX Bedienungsanleitung

Westermo

Westermo L105-S1 Bedienungsanleitung

Westermo

Westermo Viper-120A-P8-HV Bedienungsanleitung

Westermo

Westermo RedFox 5528 Series Bedienungsanleitung

Westermo

Westermo Lynx DSS L106-F2G EX Bedienungsanleitung

Westermo

Westermo Viper 12A-PoE Series Bedienungsanleitung

Westermo

Westermo Lynx SERIES Bedienungsanleitung

Westermo

Westermo Lynx L206-F2G Bedienungsanleitung

Westermo

Westermo RFIR-127-F4G-T7G-DC Bedienungsanleitung

Westermo

Westermo Lynx SERIES Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung