Whalen WSZB184872-GW5BMS Bedienungsanleitung

Date: 2019-12-27 Rev. 0001-N

Whalen Furniture Manufacturing

ITM. / ART. 991070

MODEL# WSZB184872-GW5BMS

Assembly Instructions

Customer Service: 1-866-942-5362 English, French and Spanish

Monday - Friday, 8:30 a.m. - 4:30 p.m. PST

(Telephone is not valid in Mexico, toll-free in U.S. and Canada only)

E-mail : parts@whalenfurniture.com

1. Please read instructions prior to assembly.

(Please note that there is a recommended

tool not included in this package).

2. Verify that there are no missing parts.

3. Two people are recommended for assembly.

4. Gently set parts on a flat, smooth surface.

5. For indoor use only.

“Adult assembly required due to the presence of small parts, points, and

edges as received.”

IMPORTANT, RETAIN FOR FUTURE REFERENCE:

READ CAREFULLY

SHELF MAXIMUM CAPACITY: 454 kg / 1000 lb EVENLY DISTRIBUTED.

ENTIRE UNIT MAXIMUM CAPACITY: 2268 kg / 5000 lb EVENLY DISTRIBUTED.

CONCENTRATED LOAD CAPACITY: 732.6 kg / 1615 lb PER SQUARE METER

(0.45 kg / 1 lb PER SQUARE INCH)

Storage Rack is NOT recommended for outdoor use.

1. Do not exceed 454 kg / 1000 lb per shelf. Do not exceed 2268 kg / 5000 lb per unit.

2. Weight should be evenly distributed on the shelf surface. Weight that is concentrated

in the center of the shelf will reduce the shelf capacity.

3. Load small stable items on the top shelves, heavier and bulkier items should be

stored on the lower shelves. Load unit placing objects from the bottom to top. This

will ensure stability of overall unit.

4. Never climb or stand on the unit and do not use as a ladder.

5. Not intended to be used by children.

6. Do not alter the product in any way as it could compromise the performance of the

unit as intended and will void all warranties.

Note: Larger heavier items

stored on the bottom

levels and smaller lighter

items stored on the upper

levels.

Use caution when placing

items on each shelf.

Dropping items onto the

shelf can cause an impact

load that could result in

shelf failure.

Failure to follow these guidelines can result

in properly damage or personal injuries.

Parts List

Please read completely through the instructions and verify that all parts listed are present before

beginning assembly

Tool Required: Rubber Mallet (NOT INCLUDED)

PART# PART DESCRIPTION QUANTITY

A- Angle Post

B-Long Z-beam 10

C-Short Z-beam

D- Shelf Deck

E- Post Cap

F- Post Inserts

G- Post Clips

H - Tipping Restraint

Hardware Kit

ATTENTION

1. Use some type of lubricant to ease the joining of the angle posts and beams.

2. Use a cloth or wood block to protect the surface finish of the product when using a

rubber hammer.

3. Must drive the rivets to the bottom of the keyhole by hitting the beam near the joint.

4. Assemble the unit on a sturdy and level surface. Avoid assembly on carpet.

OPTION #1 5-SHELF STORAGE RACK

Note: To facilitate assembly we recommend having two persons assemble the unit. If you

do not understand these directions, or have any doubts about the safety of the installation,

please call a qualified contractor or contact Whalen Storage at 1-866-942-5362 for

assistance. If you have any defective parts please do not use, improper installation may

result in damage or injury.

Assembly Instructions

1. Start the End Assembly by joining a Short Z-beam (part C) into the two bottom keyholes of an

Angle Post (part A). Install the Z-beam in the upright position, as shown in detail #1. Drive the

rivets to the bottom of the keyhole by hitting the beam near the joint with a rubber mallet to lock

the pieces together.

Repeat last step to the second Angle

Post (part A) creating an End Assembly.

2. Assemble a Long Z-beam (part B) to the other two bottom keyholes of the End Assembly.

Assure all Z-beams are assembled in the upright position, as shown in detail #2. Hit the beam

near the joint with a rubber mallet to lock pieces together.

Note: Don’t hit too hard so you will not damage or bend the beams.

Repeat last step to add an additional Long Z-beam, the other Short Z-beam and two Angle

Posts to the End Assembly to create the Bottom Frame Assembly, as shown in detail #2.

Note: Follow the order 1st through 5th as shown in detail #2 to facilitate the assembly. Hit the

beams near the joints to lock the pieces into place.

3rd

2nd

Assembly Instructions

3. Now pick up a Short Z-beam (part C) and join into the top two keyholes of the other 2 Angle

Posts (part A) to create a Top End Assembly. Drive the rivets to the bottom of the keyhole

with a rubber mallet. Make sure the flat edge of the Z-beam point up, as shown in detail #3.

Repeat last step for the opposite side Top End Assembly.

4. Before joining the Top End Assembly to the Bottom Frame Assembly insert Post Inserts (part F)

into the Angle Posts (part A) on the Bottom Frame Assembly, as shown in detail #4.

Proceed to assemble the Top End Assembly on to the Post Insert (part F), as shown in detail #4.

Repeat last 2 step for the opposite Top End Assembly.

5. Add a Short Z-beam (part C) to mid section at the joint by inserting the top rivet of the Z-beam

into the bottom keyhole of the Top End Assembly, and the bottom rivet of the Z-beam into the

top keyhole of the Bottom Frame Assembly, as shown in detail #5. Make sure all Z-beams are

in the upright position. Drive the rivets to the bottom of the keyholes by hitting the beam

near the joints to lock top and bottom of rack together.

Repeat last step to add an additional Short Z-beam (part C) and two Long Z-beams (part B).

6. Proceed to add two additional Long Z-beams (part B) to top two keyholes of the Angle Posts

(part A). As shown in detail #6 install the Z-beams in the upright position. Be sure to have the

rivets in the keyholes before hitting the beams near the joints to lock the pieces together.

7. Assemble the remaining Long and Short Z-beams (part B and C) to your desired location on

the Angle Post (part A) to create two additional shelves, as shown in detail #7. Be sure to

install the Z-beams in the upright position. Hit the beams near the joints to lock pieces

together.

Note: The posts are adjustable in 3.8 cm / 1.5 in increments. You can adjust the shelves to

your desired height.

Assembly Instructions

8. Now lay the Shelf Decks (part D) in between the Z-beams. See detail #8A.

Insert the Post Caps (part E) on the top of the Angle Posts (part A), as shown in detail #8B

OPTION #2 Side by Side

9. Repeat steps 1 through 2 to create a Bottom Frame Assembly.

Now insert two Short Z-beams and two Long Z-beams

(part C and B) in the top keyholes of the Angle Posts.

Hit the beams near the joints with a rubber mallet to

Lock pieces together, as shown in detail #9.

Add two additional Short Z-beams and two

Long Z-beams (part C and B) to create a

shelf at your desired level. Be sure all

Z-beams are assembled in the upright

position, as shown in detail #9.

10. Now start the Add-on Unit by joining the first Short Z-beam (part C) into the top two keyholes

of the other two Angle Posts (part A), as shown in detail #10. Hit the beam near the joints with

a rubber mallet to lock pieces together.

Repeat for the opposite end assembly.

Z-beam

Shelf Deck

Assembly Instructions

11. Complete the Add-on Unit by adding two Long Z-beams (part B) at the top keyholes of the

Angle Posts (part A), as shown in detail #11. Install all Z-beams in the upright position. Hit the

beams near the joint with a rubber mallet to lock joints into place.

12. Now lay the Shelf Decks (part D) in between the Z-beams. Make sure all Z-beams are in the

upright position, as shown in detail #12.

13. To secure the frames together, align the four middle Angle Posts (part A) of the frames, as

shown in detail #13. Start with the two back middle Angle Posts. Align the indents on the Post

Clips (part G) and two keyholes of the back middle Angle Posts. Firmly clamp together a Post

Clip and the two angle posts. Repeat the step to clamp the two front middle angle posts.

Note: To remove Post Clips use a screwdriver. Insert the Post Caps (part E) on the top of the

Angle Posts (part A), as shown in detail #13.

14. Periodically inspect the unit to ensure all Z-beams are seated properly and firmly connected to

the Angle Posts.

Shelf Dec

Flat

dge on

top

Upright Position

(Z-beam)

NOTE: The tipping restraint hardware included is for wooden stud wall construction. It must be attached to a wall

stud. Depending upon your wall construction, different anchor hardware maybe required. Please contact your local

hardware store for assistance. Young children can be seriously injured by tipping furniture. You must install the

tipping restraint hardware with the unit to prevent the unit from tipping, causing any accidents or damage. The

tipping restraints are intended only as a deterrent, they are not a substitute for proper adult supervision. The tipping

restraints are not earthquake restraints. If you wish to add the extra security of earthquake restraints, they must be

purchased and installed separately.

Care and Maintenance

 Use a soft, clean cloth that will not scratch the surface when dusting.

 Use of furniture polishes is not necessary. Should you choose to use polishes, test first in an inconspicuous

area.

 Using solvents of any kind on your furniture may damage your furniture’s finish.

 Never use water to clean your furniture as it may cause damage to the finish.

 Stains or marks from crayons or ink markers will be difficult to remove.

 Do not use any harsh abrasives or chemicals to clean any metal surfaces as it may damage the

protective coating.

 Metal will rust if the finish is scratched or if your furniture is exposed to excessive humidity, particularly in

salt water locations.

 Most metal furniture has a protective coating to prevent rust, however rust may occur if the finish is

marred or wears away over time.

 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call

a professional to repair your furniture.

 Check rivets and post clips periodically and tighten them if necessary.

Wooden stud

Screw

LIMITED LIFETIME WARRANTY

This Whalen product (exclusive of shelves) is warranted to the original purchaser. If there is a failure in this

unit due to defects in materials or workmanship, Whalen Storage will repair or replace this item at our

discretion without charge. Warranty is void if product has been assembled incorrectly, misused, abused by

overloading, altered in any way or damaged due to accident. This warranty is not transferable and does not

cover chipping, flaking, scratches, rust, dents, or other damages to the surfaces of this product.

Responsibility of Whalen Storage is limited to repair or replacement of this product. Whalen Storage is not

responsible for consequential incidental, or other damages or losses resulting from product failure.

This warranty is in lieu of all other expressed warranties. Some adapt for Canada do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation may not apply to you. This

warranty gives you specific legal rights and you may have other rights which vary from adapt for Canada.

In case of product failure, damage or defective parts refer to:

Whalen Furniture Manufacturing

1578 Air Wing Rd.

San Diego, Ca. 92154 USA

1-866-942-5362

KEEP THESE INSTRUCTIONS FOR FURTHER REFERENCE

Your assembly should now be complete.

Thank you for your purchase.

Serious or fatal crushing injuries can occur from furniture

tip-over. To help prevent tip-over:

 Place heaviest items on the lowest rack.

 Do not place heavy objects on the top of this product.

 Never allow children to climb or hang on the shelves.

Use of tip-over restraints may only reduce but not eliminate the risk of tip-over.

Contact your local hardware store for tip-over restraints that will best meet the

are

a where

nit wi

ll be used.

AUSTRALIA: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable

quality and the failure does not amount to a major failure.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Whalen Inneneinrichtung Handbücher

Whalen

Whalen Annual Event WMFP41BT-2 Bedienungsanleitung

Whalen

Whalen Sonoma Ridge Desk Bedienungsanleitung

Whalen

Whalen LWS30DCVAG Bedienungsanleitung

Whalen

Whalen Cecile ODUS-48CD-B Bedienungsanleitung

Whalen

Whalen WF36FVB Bedienungsanleitung

Whalen

Whalen ODUS-TWVD Bedienungsanleitung

Whalen

Whalen Bayside FURNISHINGS 369333 Bedienungsanleitung

Whalen

Whalen BSKY-368036 Bedienungsanleitung

Whalen

Whalen WF60EVB Bedienungsanleitung

Whalen

Whalen odus-tdpd Bedienungsanleitung

Whalen

Whalen Bayside CSCGLBST-4-UK-BL Bedienungsanleitung

Whalen

Whalen WSHD5PSB Bedienungsanleitung

Whalen

Whalen Vellore Barstool Bedienungsanleitung

Whalen

Whalen Bayside CSC7PD-12-UK Bedienungsanleitung

Whalen

Whalen Sagemoor SAGE7PD-E Bedienungsanleitung

Whalen

Whalen Peruzzi SPLS-PE48D Bedienungsanleitung

Whalen

Whalen Kendal Chair Gray Bedienungsanleitung

Whalen

Whalen WF60AVG Bedienungsanleitung

Whalen

Whalen Midland Twin over Full Bunk Bed Bedienungsanleitung

Whalen

Whalen Bayside CSC9PD-6 Bedienungsanleitung

Whalen

Whalen Bayside FURNISHINGS CSC3N1C-56-6 Bedienungsanleitung

Whalen

Whalen Dulzura SPUS-DZMF-LBM Bedienungsanleitung

Whalen

Whalen LWS60DCVAG Bedienungsanleitung

Whalen

Whalen BBHC60DBC Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung