WHEELSWING VOLT 1 Bedienungsanleitung

WHEELSWING VOLT 1

User Manual

[ Please read before using the product! ]

WHEELSWING VOLT 1

User Manual

This manual has been produced as of the present, and there may be technical or editorial errors or omissions.

For product performance improvement, product changes may be made without notice to the user.

Electricity production may vary depending on the driving speed and driving conditions of the bike. Please note this.

A contactless rim dynamo : it can be mounted on rim brake bikes, spin bikes, and stationary bikes.

A contact rim dynamo : it can be mounted on all types of bikes, spin bikes, and stationary bikes.

To obtain information on installation and adjustment of products not included in the user manual,

Please contact customer center. (Refer to Page 9 “Product specification and C/S”)

For safety, please read the user manual carefully before using the product and follow it for correct use.

Caution and Prohibition: Users of pacemakers and implantable cardiac defibrillators should not move

or use this bicycle generator near the heart as the magnetic field of the bicycle generator can cause

the failure of these medical devices.

● Be sure to read all instructions carefully before installing any part.

● Do not leave the product in a hot place, such as a heat source or a vehicle parked under

direct sunlight. To avoid damage to the product, remove it from the vehicle or store it out of

direct sunlight.

● Do not drop the product from high places. It may cause problems with product functionality.

● Before boarding, please check whether the alignment between the body and the wheels is correct

If the alignment is not correct, the amount of power generation may be small, or power generation

may not be possible.

● We do not guarantee the loss of functionality due to normal wear and tear of the product over time

and daily use.

● This product has waterproof function (IPx5), but damage caused by flooding is not guaranteed.

Do not immerse the product in water or wash it with high pressure water.

● This product can be used even on rainy days but be careful not to get water into the USB terminal.

● If you have any problems with maintenance or use, please contact the customer center.

● Do not disassemble, modify, reassemble, break, or damage this product.

● Before boarding, make sure that the product is securely fixed to the side of the wheel and

that the bolts are fully tightened. If the product becomes loose and the product is caught between

the spokes or the frame and the wheels, serious injury may result.

● After reading the user manual, keep it in a safe place for future reference.

● Do not overtighten the screws during the installation process. The bracket or product connection

may be damaged.

● This product is a 5V, 500mAh output product. Do not connect products with high voltage and

current to the input or output USB ports. It may cause malfunction.

Failure to pay attention to the following may result in

unexpected damage due to incorrect usage.

Warning

Failure to pay attention to the following may result in personal injury

or property damage, or adversely affect the function of the device.

Important safety and product information

Warning

WHEELSWING VOLT 1

Key features

Non-contact drive system

The world's first and the world's only bike generator

Self-generation

Charge with homemade electricity!

You can continue to create and use electricity

while riding.

Built-in battery

Built-in 1A Li-ion battery allows you to charge with

stored electricity even while your bike is at a standstill.

(VOLT1-NCB / CB)

USB charging method

You can easily and conveniently charge all devices

connected by USB.

Simple installation

Self-installation is possible

without expert assistance.

Universal bracket

It mitigates vibration in two steps and can be installed

anywhere on the front/rear wheel.

Hybrid method

By simply replacing the rubber ring, you can quickly

change the driving method to a contact type.

(VOLT1-NCB / NCD)

The contact type is driven by mounting two types of

self-developed rubber rings (booster rings).

Light pedaling

Unlike ordinary bicycle generators,

the pedaling is light and the driving feel is smooth.

Reliability test

This product has undergone rigorous testing for safety.

Waterproof design

IPX5 waterproof design makes life waterproof.

WHEELSWING

Contactless

System

Battery

built-in

USB

Recharging

Light

pedaling

Simple

Install

Universal

bracket

Hybrid

generator

Durability

test

USB

Charger Phone Bettery Light GPS Earphone Action

camera Cycling

computer NavigationSpeaker

Product composition

Contactless generator

(NCB/NCD)

Equipped with thin bumper ring

Contact generator (CB/CD)

Equipped with thick booster ring

WHEELSWING VOLT1 consists of the generator body, bracket, crescent, rubber ring, rubber pad,

bolt/nut, and installation guide.

Filler gaugeBumper ring Booster ring N Booster ring W Booster ring N

Contactless Contact

Rubber pad S Rubber pad R Bolt/Nut Installation

Generator body Bracket Crescent P Crescent R

● How to assemble the bracket (for both a contactless/contact rim dynamo)

Installation of a contactless/contact rim dynamo

What you will need is the bracket, crescents,

and rubber pads

Assemble the bracket by combining rubber pads and

crescents according to how thick forks and seat stays are

● How to secure the bracket and generator body

(for both a contactless/contact rim dynamo)

What you will need is the assembled bracket,

generator body, bolts, and nuts

Using an installation guide, check whether the end of

the generator’s head sits near the rim’s end side

Insert the bracket into either forks or seat stray,

and secure it with bolts and nuts

(Don’t secure it tight; you will need to

adjust the position later)

Insert the generator body to the bracket,

and secure it with bolts and nuts

Installation of a contactless/contact rim dynamo

● Installation of a contactless rim dynamo

Insert the gauge into the gap of the rim

Move the tire forward so that the gauge is placed

between the head of the generator body and the tire

Slightly adjust the bracket and generator body

left/right or up/down so that there is no empty space

between the gauge and the body

Make sure that the marked point on the picture has

no crack or gap between the gauge and the body

Firmly tighten the bracket

and bracket-generator body fixing bolts and nuts

Installation finished

● Installation of a contact rim dynamo

Slightly adjust the bracket and generator body

left/right or up/down so that the booster ring

touches the rim

Firmly tighten the bracket and bracket-generator

body fixing bolts and nuts

Installation finished

● How to use a contactless rim dynamo

When installed incorrectly, it can cause vibration and noise.

It might fail to generate an adequate amount of electricity

or do not work at all.

Check the angle of the generator body

Place the bumper ring on the border of the rim.

How to use properly

*What you need to check before every ride

● How to use a contact rim dynamo

*What you need to check before every ride

Use a tweezer to slightly lift the rubber ring and remove it,

when it is difficult to replace it using hands.

Replace rubber rings

Be sure to install the booster ring sitting near the bicycle tire,

but not touching it. It can cause extra wear on tires.

Contact of the rubber rings

It is important for the magnet inside the generator head and

the rim to work properly. Therefore, the larger the surface area is,

the more electricity the dynamo would generate.

When the surface area is small, the dynamo might produce a

different amount of electricity or do not work at all.

Check the surface area where the rim and

generator head faces

Put the head as close to the rim as possible without touching the rim.

(Keep a distance of 1-2mm between the head and the rim)

If they are too far or too close, the dynamo might produce a

different amount of electricity or do not work at all.

Check the distance between the rim and

the generator head

Product specification and C/S

Product Registration

Failure occurred within the warranty period under normal use according to the precautions in the user manual.

In this case, you can get free repair.

Even within the warranty period, repair fees are incurred in the following cases.

1) Breakdown and damage due to misuse or improper repair, disassembly, or modification

2) Failure or damage due to transportation or dropping after purchase

3) Failure and damage due to natural disasters such as fire, earthquake, flood, lightning, and pollution

4) Damage caused by external factors when used in a manner not described in the user manual

5) Breakdown and damage caused when used for purposes other than general bike generators

If you would like to make a request for repair, please contact the customer center.

This warranty is only valid in the country and region of purchase.

● [Contactless] Product specifications

Product Name Contactless battery built-in type bike generator

WHEELSWING VOLT1-NCB

148X134X67.5mm (5.8X5.2X2.6X in)

390g (0.85lb)

Li-ion battery 1,000mAh

Model Name

Size

Weight

Material

Capacity

Battery

● [Contact] Product specifications

● Common

● C/S regulation

Contact battery built-in type bike generator Contact direct charging type bike generator

WHEELSWING VOLT1-CB

148X134X67.5mm (5.8X5.2X2.6X in)

345g (0.76lb)

PC, rubber, silicone, etc.

USB2.0 (5V,500mAh output)

Li-ion battery 1,000mAh

WHEELSWING VOLT1-CD

148X134X67.5mm (5.8X5.2X2.6X in)

320g (0.7lb)

PC, rubber, silicone, etc.

USB2.0 (5V,500mAh output)

Manufacturer

Country of Origin

Manufacturing date

Warranty period

Customer Center

WITHUS & EARTH Co., Ltd. within 1 year after purchase

Tel : +82-53-213-8802

E-mail : [email protected]o.kr

Republic of Korea

Separately indicated

PC, rubber, silicone, etc.

USB2.0 (5V,500mAh output)

Contactless direct charging type bike generator

WHEELSWING VOLT1-NCD

148X134X67.5mm (5.8X5.2X2.6X in)

365g (0.8lb)

PC, rubber, silicone, etc.

USB2.0 (5V,500mAh output)

Within two weeks after purchasing the product, scan the QR code on the customer center in

the manual, add KakaoTalk Plus Friend [WHEELSWING] as a friend, and then register the

product. Please take a picture of the [Quality assurance certificate] in the black and white

manual enclosed with the product and send it to us.

Customer benefits upon product registration

Product Name

Model Name

Size

Weight

Material

Capacity

Battery

- Free C/S for 1 year after purchase

- Notify when new information is updated

- Provide customer convenience service

For more details and installation method, you can check the website and YouTube video.

The Generator for all bike in the world

Website YouTube Customer Center

WHEELSWING VOLT 1

User Manual

For users

Andere Handbücher für VOLT 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere WHEELSWING Fahrradzubehör Handbücher

WHEELSWING

WHEELSWING VOLT 1 Bedienungsanleitung

Beliebte Fahrradzubehör Handbücher anderer Marken

Sigma

Sigma BC 16.16 Bedienungsanleitung

Playcore

Playcore Dero Setbacks Bedienungsanleitung

VDO Cyclecomputing

VDO Cyclecomputing x3dw Bedienungsanleitung

Cateye

Cateye RAPID X2 Bedienungsanleitung

buratti meccanica

buratti meccanica Clorofilla Trail Bedienungsanleitung

Shimano

Shimano SG-8R20 Betriebsanleitung

BOB

BOB YAK Bedienungsanleitung

APLIC

APLIC 303303/20190717TW012 Bedienungsanleitung

SRAM

SRAM AXS BlipBox Bedienungsanleitung

Garmin

Garmin EDGE 500 Bedienungsanleitung

Shimano

Shimano FD-RX810 Bedienungsanleitung

Cateye

Cateye V2C - Gebrauchsanweisung

KMART

KMART 43115907 Bedienungsanleitung

SIGMA SPORT

SIGMA SPORT Buster 2000 Bedienungsanleitung

NVO Components

NVO Components STEM Bedienungsanleitung

DAXYS

DAXYS BP188 Bedienungsanleitung

XLC

XLC BV-W17 Bedienungsanleitung

Deda Elementi

Deda Elementi SUPERBOX Bedienungsanleitung