Whelen Engineering Company 2022 Series Bedienungsanleitung

Page 1

Form No.13437F (102207)

Installation Guide:

2022 Series Strobe Beacons

(Polycarbonate Base)

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Fax: (860) 526-4078

Internet: www.whelen.com

Sales e-mail: autosale@whelen.com

Canadian Sales e-mail: autocan@whelen.com

Customer Service e-mail: custserv@whelen.com

Automotive: Beacons

Safety First

This document provides all the necessary information to allow your Whelen product to be properly and safely installed.

Before beginning the installation and/or operation of your new product, the installation technician and operator must

read this manual completely. Important information is contained herein that could prevent serious injury or damage.

• Proper installation of this product requires the installer to have a good understanding of automotive electronics,

systems and procedures.

• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other

vital parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling

begins. Also de-burr the holes and remove any metal shards or remnants. Install grommets into all wire passage

holes.

• If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro®, clean the

mounting surface with a 50/50 mix of isopropyl alcohol and water and dry thoroughly.

• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or

located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a

projectile that could cause serious personal injury or death. Refer to your vehicle owner’s manual for the air bag

deployment area. The User/Installer assumes full responsibility to determine proper mounting location, based

on providing ultimate safety to all passengers inside the vehicle.

• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be

made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE

(-) battery post (this does not include products that use cigar power cords).

• If this product uses a remote device for activation or control, make sure that this device is located in an area

that allows both the vehicle and the device to be operated safely in any driving condition.

• Do not attempt to activate or control this device in a hazardous driving situation.

• This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination of these

lights. Do not stare directly into these lights. Momentary blindness and/or eye damage could result.

• Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens cracking

(crazing) and discoloration. Lenses in this condition have significantly reduced effectiveness and should be

replaced immediately. Inspect and operate this product regularly to confirm its proper operation and mounting

condition. Do not use a pressure washer to clean this product.

• It is recommended that these instructions be stored in a safe place and referred to when performing

maintenance and/or reinstallation of this product.

•FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE TO

THE PRODUCT OR VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!

ENGINEERING COMPANY INC.

For warranty information regarding this product, visit www.whelen.com/warranty

Page 2

#4 X 1/2"

PHILLIPS PAN

HEAD SMS

PCB

ASS'Y

OPTIC

DOME

BASE

#10X5/8"

PPH SMS

FASTEX

GROMMET

When inserting the flash

tube assembly into the

strobe power supply

assembly, align the 3

prongs on the flash tube

with the slots in the

power supply.

BASE

SEAL

#6 X 5/8" PAN HD.

THX HD. SCREW

#6 X 5/16" HEX WSHR

HD THD FORM. SCREW

FLASH

TUBE

ASS'Y

IMPORTANT:

Keep drain hole

in base facing

rear of vehicle.

HI /LOWGH POWER

If you wish to control Hi/Low Power

externally, cut the VIOLET wire off at this

point and exit with the BLACK and RED

wires. Ground this wire to go to high

power. You may install an SPST switch

(customer supplied).

FLASH PATTERN SELECTION

To achieve any of the 4 flash patterns,

you must either cut-out or leave-in one,

two, both or neither of the two jumpers.

you do not touch the jumpers the beacon

will default to QuintFlash.

PCB ASSEMBLY (COMPONENT SIDE)

JU1

BLK

JU2

RED

JU6

QuintFlash

DoubleFlash

RapidRandom

ActionFlash™

JU1 JU2

CUT

FLASH PATTERNS

FLASH PATTERN SELECTION

HI/LOW POWER CONTROL

O-RING

GASKET

Assembly and Operation:

Specifications:

Input Voltage.................................................................. 12.8 / (25.6) VDC

Input Current..................................................2.5 Amps & 1.25 Amps avg.

Input Power............................................................................... 31.5 Watts

Flashrate: QuintFlash™.......................... 72 QuintFlashes (5) Per Minute

DoubleFlash .......................... 115 Double Flashes Per Minute

RapidRandom......................150-370-150 Flashes Per Minute

ActionFlash ....... 1 QuintFlash & 4 Single Flashes Per Minute

Energy ........................................................8.6 / 2.5 / 2.5 / 2.5 / 2.5 Joules

Output Power............................................................................... 22 Watts

WARNING!The strobe power supply is a high voltage device. Do not

remove flash tubes or dismantle the strobe light head

assembly while in operation. Wait 10 minutes after turning

power off before starting work or trouble shooting.

Mounting:

1 Inch (NPT) Pipe Mount:

1. Threading for a 1 inch (NPT) pipe mounting is precast in the base.

Feed power cable through pipe and connect cable to beacon.

2. Screw strobe beacon to threads on the pipe, taking precaution not to

damage the power wires. NOTE: Do not tighten base too hard

onto pipe so as not to damage the threads on the base.

Permanent Mount:

1. Use the base as a template and mark the three mounting holes onto

the mounting surface. After removing the base, mark in the center

between the 3 mounting holes, the location of the wire access hole.

2. Drill the mounting holes using a #16 drill bit. Drill a wire access hole

using a 3/8” drill bit. Remove the burrs from the wire access hole so

as not to damage the wires. It is recommended that you install a

rubber grommet to further protect the wires. A gasket will be used

between the beacon base and the mounting surface.

3. After connecting the beacon to the power cable, feed the wires

through the cable access hole and place the base with the gasket on

the mounting surface, lining up the mounting holes in the base with

the mounting holes in the mounting surface. Secure beacon firmly to

the mounting surface with the #10 X 5/8 Sheet Metal Screws.

Temporary Mount:

Magnetic/suction: Thoroughly clean the proposed mounting surface prior

to mounting. For suction cup mounting, wipe the suction cup clean, place

the beacon onto its mounting surface and apply gentle pressure to ensure

a good seal. The Magnetic/Suction Cups mount the same way as

standard suction cups but are best suited to a flat, steel surface.

Magnetic: Place beacon onto mounting surface and plug into cigar lighter.

WARNING! Beacons equipped with cigar cords are intended for

shortduration, intermittent operation only! Prolonged

operation requires the beacon to be wired to the vehicle.

WARNING! The presence of any temporarily mounted warning light

on the outside of a vehicle in motion is not

recommended and is at the sole discretion and liability

of the user!

WARNING! All customer supplied wires that connect to the positive

terminal of the battery must be sized to supply at least

125% of the maximum operating current and FUSED at

the battery to carry the load. DO NOT USE CIRCUIT

BREAKERS WITH THIS PRODUCT!

DC voltage models are polarity sensitive. If the positive and negative wires

are reversed the unit will not function. The fuse is installed between the

power source and the beacon, in the positive (+) wire (RED) and must be

fused at the battery. A 7.5 AMP Fuse is Recommended for this unit.

1. Connect the RED wire on the beacon to positive voltage (+). A

customer supplied single pole single throw (SPST) switch may be

used to control the ON/OFF function of the beacon.

2. Connect the BLACK wire on the beacon to a negative (-) ground.

10-24

ELASTIC

STOP NUT

(QTY 4)

10-24 X 5/8

U-BOLT

(QTY 2)

1. Secure the bracket to the mirror

2 supplied U-Bolts and elastic1.

or other part of the vehicle using the

stop nuts.

Mirror Mount Bracket

10-24 X 7/8

PPHMS

(QTY 3)

10-24

ELASTIC

STOP NUT

(QTY 3)

2. using the supplied sheet metal

screws

Secure the Beacon to the bracket

and elastic stop nuts.2.

Page 3

01-0683147LAV

25-0510523-05

14-130216-160

06-143328-000

13-130111-073

69-1340052-00

08-1583927-05

38-0441331-00

68-2180452-10

01-0683147LAP

15-065410-100

36-0341567-00

15-041416-080

02-0168306-00

06-181468-001

38-0241596-00

68-2180483-10

15-101416-100

01-0461585-00

15-066939-056

06-182589-001

01-0683147HAP

01-0683147LAM

111

STROBE LIGHT ASSY MODEL 2022MP/VP422MP/

STROBE LIGHT ASSY MODEL 2022LV/

STROBE LIGHT ASSY MODEL 2022LP/

STROBE LIGHT ASSY MODEL 2022HP/

SUCTION CUP / MAGNET SUCTION CUP MOUNT

#6 x 5/16" HEX WASHR HD. THD. FORMING SCREW

DOME AMBER HIGH//

FLASH TUBE ASS'Y FTU 20W/

#4 X 1/2" PHILLIPS PAN HD SMS SS

PCB ASSY MODEL 2022 SERIES/

BASE STROBE PLASTIC//

SEAL-BASE MODEL 2000 SERIES B/

#10 x 5/8" PPH SHEET METAL SCREW

#6 X 5/8" PAN HD. THD. FORM SCREW

DOME AMBER/

BUTT TERMINAL #34071

1/4-20 X 1" PPHMS SS SCREW

BASE VACUUM MOUNT STROBE LIGHT ASS'Y/

1/4-20 WIZ CAD PLATED NUT

CIGAR CORD PORTABLE/

O-RING ROTATING BEACON ASSEMBLY/

KIT MAGNET MOUNT 2000 SERIES B//

BASE STROBE PLASTIC MAG. MT.///

ITEM PART NUMBER DESCRIPTION

QTY QTY QTY QTY

111

BLACK / GROUNDRED / +12 VDC

1" NPT PIPE

(2) BUTT

TERMINALS

POWER

SUPPLY

WIRING DIAGRAM

RED BLACK

GROOVED

SMOOTH

GROMMET

1/4X11/4PHSMS

PHILLIPS TYPE AB

1/4 SPLIT

LOCKWASHER

MAGNET

SEE WIRING

DIAGRAM

SEE WIRING

DIAGRAM

MAGNETIC MOUNT

OPTION

CIGAR PLUG

& CORD

FOAM GASKET

SUCTION/MAGNET MOUNT

OPTION

PERMANENT MOUNT

OPTION

DOME:

H - HIGH DOME

L - LOW DOME

BASE:

P - PERM MOUNT

M - MAGNETIC MT.

V - VACUUM MT.

COLOR:

R - RED

B - BLUE

G - GREEN

A - AMBER

C - CLEAR

V - VIOLET

DOME

HEIGHT

PART N0. KEY: BASIC PART NUMBER

+ 3 LETTERSPART N0. KEY:

01-0683147___

COLOR BASE

TYPE

STROBE LIGHT BEACON / MODEL 2022 / PARTS

MTG. HOLES FOR

#10 SCREWS (3)

3/8" DIA. WIRE

ACCESS HOLE

5.937" DIA. B.C.

MOUNTING DIMENSIONS

PERMANENT MOUNT

WIRING DIAGRAM

ALL FUSES AND SWITCHES

ARE CUSTOMER SUPPLIED

(+)

Battery

(-)

BLACK / GROUND

VIOLET / HI/LOW

RED / POSITIVE

SPST

SWITCH

SPST

SWITCH

5 AMP FUSE

Andere Whelen Engineering Company Sicherheitssystem Handbücher

Whelen Engineering Company

Whelen Engineering Company IPS 400 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company L21LAM Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Super-LED L31HBF Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 3012 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Traffic Advisor TA837A Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 1010 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WPS-2900 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Super-LED L32-Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WS295HFS1 Series Montageanleitung

Whelen Engineering Company

Whelen Engineering Company IS3 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company RB6PAPS Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company GTT 795DM Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company SS361 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company B6MM Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WS2100 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 2015 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company IS1 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company RB6T Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 72000 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company ISB Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 1502M Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company L21 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 6220-01-057-0746 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company RB6 Series Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung