Whispbar K324W Bedienungsanleitung
K324W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 8 x 4 x 4 x 4
Revision No: 6F 1
Fitting Kit EN
K324W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
2
Fitting Kit EN
K324W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
3
Fitting Kit EN
K324W
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Select a guttermount assembly from fitting
kit. Unscrew and remove clamps.
4
Fitting Kit EN
K324W
●Assemble guttermount assembly into leg
(ensure guttermount blade interlocks with
leg).
●Using short capscrew and washer, secure
assembly onto leg (use Hex Screwdriver
supplied with crossbar to assist)
●Tighten firmly (3Nm).
●Use two M5 x 12mm self tapping screws to
secure the leg to the guttermount blade.
●Do not over tighten.
●Repeat for all legs.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
5
Fitting Kit EN
K324W
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Place crossbar into gutter of vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Loosely position crossbar ensuring the
guttermount blade is hard against the
inside of the vehicle gutter.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
6
Fitting Kit EN
K324W
●Loosely line up clamp over the vehicle
gutter.
●Use same capscrew and washer to secure
clamp onto leg.
●Once crossbars are in position, tighten
screw to 3 Nm (2.2 ft lb).
●Repeat for all legs.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
7
Fitting Kit EN
K324W
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
8
Fitting Kit EN
K324W
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
9
Fitting Kit EN
K324W
●Check and replace worn out or defective
parts.
●Keep the product clean and maintained.
●Never drive into a car wash with the roof
rack system fitted.
●Lubricate locks and adjusting screws at
regular intervals.
●Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
●Yakima Australia Pty Ltd
17 Hinkler Court
Brendale QLD 4500
AUSTRALIA
www.whispbar.com
www.whispbar.com.au
www.whispbar.co.nz
www.whispbar.co.uk
www.whispbar.co.za
www.whispbar.eu
www.whispbar.ca
10
Inhaltsverzeichnis
Andere Whispbar Autozubehör Handbücher
Whispbar
Whispbar K816W Bedienungs- und Installationshandbuch
Whispbar
Whispbar K426W Bedienungsanleitung
Whispbar
Whispbar K068W Bedienungsanleitung
Whispbar
Whispbar K581W Bedienungs- und Installationshandbuch
Whispbar
Whispbar K554W Bedienungsanleitung
Whispbar
Whispbar K586W Bedienungsanleitung
Whispbar
Whispbar K077W Bedienungs- und Installationshandbuch
Whispbar
Whispbar K409W Bedienungsanleitung
Whispbar
Whispbar K905W Bedienungsanleitung
Whispbar
Whispbar K568W Bedienungs- und Installationshandbuch
Whispbar
Whispbar K069W Bedienungsanleitung
Whispbar
Whispbar K582W Bedienungsanleitung
Whispbar
Whispbar K082W Bedienungsanleitung
Whispbar
Whispbar K097W Bedienungsanleitung
Whispbar
Whispbar K907W Bedienungsanleitung
Whispbar
Whispbar K393W Bedienungsanleitung
Whispbar
Whispbar K857W Bedienungsanleitung
Whispbar
Whispbar K783W Bedienungsanleitung
Whispbar
Whispbar K475W Bedienungsanleitung
Whispbar
Whispbar K478W Bedienungs- und Installationshandbuch
