WIKORA WKS 155 Technisches Dokument

Errors excepted.

WIKORA GmbH

Friedrichstr. 9

89568 Hermaringen

Phone: (07322) 9605-0

Fax: (07322) 9605-30

email: contact@wikora.de

Installation manual

Operating instructions

Chilled water buffer tank

WKS 155 –3005

Installation and commissioning must be

undertaken by a specialist.

General terms and conditions of warranty state that

all installations must be carried out by a suitably

trained and qualified plumber who observes the

local norms and regulations.

The installation and maintenance record must be

entirely completed and the user has to be

instructed accordingly.

Efficient operation can only be guaranteed if the

instructions of this manual are followed.

Warranty does not cover any damage caused due

to non-observance of this manual and the technical

rules in force.

The system is to be checked annually by a

specialized company. In addition, occurring defects

must be repaired immediately.

This document should be handed over to the

client on completion of the installation.

Index

1 General............................................................................................................................................................................. 2

2 Transport and installation .................................................................................................................................................. 2

3 Dimensions and connections............................................................................................................................................. 3

4 Technical data...................................................................................................................................................................4

5 Installation.........................................................................................................................................................................4

6 Commissioning..................................................................................................................................................................4

7 Maintenance and wear parts.............................................................................................................................................. 4

8 Recycling and disposal......................................................................................................................................................4

9 Warranties and guarantee.................................................................................................................................................5

10 Installation record .............................................................................................................................................................6

Errors excepted.

1 General

Depending on the type and design, WIKORA tanks are suitable for water storage. The maximum working pressure and working

temperature can be found in the technical data.

Set-up, installation and commissioning must be undertaken by a qualified specialist, who must observe these instructions.

The site of installation must be frost-protected according to DIN 4753.

When setting-up and installing the tank, the following regulations should be considered:

In addition to the technical rules in force DIN 1988, DIN 18160, DIN 4753, DIN 4109, DIN 4708, DIN 4751 section 2-4 energy

conservation law and VDE regulations are to be observed. Moreover, the relevant regulations of the suppliers as well as legal

building regulations are to be considered.

2 Transport and installation

In order to prevent damage during transport, the packaging should only be removed at the site of installation. During shipment,

it should be ensured that the tank does not come in contact with any spiky or sharp items, nor is damaged through dropping or

knocks.

During installation, the tank must be disconnected from any humidity carrying components. Moreover, sufficient space for

maintenance and cleaning purposes should be kept free in front of, beside, above and behind the tank.

The pre-assembled PS-jacket can be dismantled for installation. Damages which have been caused in the thermal insulation

during installation must be professionally repaired.

The PS-jacket including rosettes are to be placed at the site of installation before installing the pipeworks.

Errors excepted.

3 Dimensions and connections

Chilled water buffer tank on base ring, interior not coated, exterior primer-painted for thermal insulation, 25 mm thermal

insulation and PS-jacket in RAL 9220, pre-assembled with rosettes and cap.

Manufactured in compliance with AD 2000 regulations and company standards, manufacturer’s certificate for construction and

pressure testing.

llustration 1

Dimensions:

Type

[mm]

WKS 155

500

552

884

915

656

233

618

467

265

WKS 205

500

552

1128

1120

900

233

862

564

265

WKS 305

500

552

1641

1665

1413

233

1372

819

265

WKS 405

600

652

1635

1660

1395

265

1370

985

300

WKS 505

600

652

1895

1900

1655

265

1640

970

300

WKS 805

790

842

1802

1845

1520

290

1490

903

316

WKS 1005

790

842

2117

2150

1835

290

1805

1061

316

WKS 1505

1000

1052

2074

2130

1730

350

1680

1040

400

WKS 2005

1200

1252

2013

2100

1625

395

1575

1010

445

WKS 3005

1250

1302

2603

2680

2220

390

2170

1305

440

Chart 1

W = Tilting dimension; d = WKS excl. insulatione, D = WKS incl. insulation

Connections:

Type

WKS

155

WKS

205

WKS

305

WKS

405

WKS

505

WKS

805

WKS

1005

WKS

1505

WKS

2005

WKS

3005

Load flow / return

8/9

1 1/2

2 1/2

Vent

1 1/4

Sensor socket

1/2

Drain

(5)

1 1/4

Chart 2

Gi = female thread

Errors excepted.

4 Technical data

Description

WKS

155

WKS

205

WKS

305

WKS

405

WKS

505

WKS

805

WKS

1005

WKS

1505

WKS

2005

WKS

3005

Storage volume (real) acc.

to DIN EN 12897

[litre]

153

201

300

431

500

830

983

1535

2010

3035

Max. working temperature

[°C]

Min. working temperature

[°C]

Max. working pressure

[bar]

Max. rel. humidity

[%]

Max. env. temperature

[°C]

Weight (empty)

[kg]

100

103

122

151

206

234

273

359

431

Chart 3

5 Installation

All pipes connecting to the tank should have removable connections (fitting/flange). Pipe thread seals with teflon are to

be avoided.

All tank connecting pipes are to be planned, constructed and tested according to the technical rules in force, as well as to the

corresponding norms and regulations in accordance with their application and supply medium.

Sensors and thermostats necessary for temperature control must be securely and permanently positioned on the tank

(immersion sleeve and sensor rail).

The tank’s venting and draining facilities must have the appropriate dimensions and be correctly installed.

The installation company is responsible for the correct execution of work and for the safe and careful insulation of the pipes.

All factory-made, non-insulated surfaces must be insulated in a professional manner on site.

6 Commissioning

Before putting into operation, the entire system should be flushed through. Particles in the system compromise the

operating reliability.

Fill the heating system slowly with water and vent all the air.

Start-up the system.

Before the handover of the system to the end user/owner, the plumbing contractor should ensure that the

system is tested to full load, controls are set and that pipe work and connections are without leaks. Afterwards,

the end user has to be instructed in the operation and handling of the tank, as well as the system. The instruction

must to be documented in the installation and maintenance record.

Please note that the operation and lifetime of the system depend decisively on a regular maintenance.

7 Maintenance and wear parts

Regular maintenance increases the lifetime and operation reliability of the system.

A damp cloth is sufficient to clean the outer parts. Please avoid using any abrasive or solvent cleaning.

8 Recycling and disposal

The products are specified and manufactured according to VDI 2243. The products are mechanically separable and 100%

recyclable. Make sure that the components are disposed according to the relevant regulations.

Errors excepted.

9 Warranties and guarantee

The warranty for our products is based on the legal provisions of the general Civil Code and the Consumer Protection Act.

In addition, defective appliances are replaced within the framework of our full warranty within 1 year, as of the date of the

invoice, including the replacement, procurement and incidental costs. As far as our hot-water heaters and pressurized boilers

are concerned, the warranty amounts for 6 months, as of the date of the invoice.

Subsequent to the full warranty, defective tanks are replaced within the framework of our guarantee. The guarantee of the

different products and the conditions are shown in the table below.

All other claims are excluded. Repairs and costs which occur due to damage, inappropriate installation, chemical,

electrochemical or electrical influences, incorrect operation or improper manipulation, are excluded. Furthermore, the warranty

becomes invalid if th eappliance has been modified through the installation of externally supplied parts or through irregular

professional maintenance.

Subject to our general terms and conditions.

Legal

warranty

2 years

Guarantee

years*

Conditions

WBO T/ToF ●5 20 / 27

WBL ●5 20 / 27

WBO Uno ●5 20 / 27

WBO Duo ●5 20 / 27

WP/Sol ●5 20 / 27

WBO H ●5 20 / 27

GS ●5 20 / 27

Wikosol Twin ●10 27

Wikosol ●10 27

WPKR H Twin ●5 20 / 27

WPKR Twin ●5 20 / 27

WPKR ●5 20 / 27

WPK ●5 20 / 27

WPH-FW (tank) ●527

WPR-FW (tank) ●527

WPS ●5 20 / 27

WPH ●5 -

WPR ●5 -

WPRR ●5 -

WKS ●5 -

Cu-finned tube heatexchanger ●-27

Electric heating element ●- -

Conditions:

Coverage Germany:

Compliance with the limits of the valid DHW regulations(TrinkwV2001), especiallythe

limits in accordance with Appendix2,Part 1-2 and Appendix3

Coverage EU :

Compliance with the limits of the EG-Regulations 83/98

* Start of guarantee at date of invoice

Products

DHW storage tanks

Combi buffer tanks

Buffer tanks

Tank accessories

Under condition that the limits of the valid DHW regulations have been respected, the

anode has been examined for the first time after 2 years and afterwards annuallyand that

the anode has been replaced byan original Wikora anode (individual receipts needed) by

a specialized company.

Errors excepted.

10 Installation record

The installation has been completed according to DIN and the technical rules in force. In addition, the customer has received

instruction concerning the operation and maintenance.

Place……………………………………………….. Date…………………………………………………………

Customer Installer

……………………………………………………. ……………………………………………………………….

Signature Signature

Place of installation: ………………………………………………………………………………………………………………………

Name: ……………………………………………………………………………………………………………………...

ZIP Code/Place: …………………………………………………..………………………………………………………………….

Street: ……………………………………………………………………...………………………………………………

Phone: ……………………………………………………………………………...……………………………………...

Tank model: ………………………………. Serial number …………….………………..………………

Date of invoice ………………………………………………………...…………………………………………………………..

In the case of reclamation, the receipts for maintenance must be provided as proof. Please complete the data sheet, including

the reason for reclamation, and submit to Wikora.

Submitting the maintenance record does not ensure any promise of guarantee or claim.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere WIKORA Boiler Handbücher

WIKORA

WIKORA WBO 605 H Technisches Dokument

WIKORA

WIKORA WPKR 750 Technisches Dokument

WIKORA

WIKORA WBO 506 UNO Technisches Dokument

WIKORA

WIKORA WBL 150 Technisches Dokument

WIKORA

WIKORA WBO 155 UNO Technisches Dokument

WIKORA

WIKORA WBO 306 UNO Technisches Dokument

WIKORA

WIKORA WBO 505 UNO Technisches Dokument

WIKORA

WIKORA WBO 120 TB Technisches Dokument

WIKORA

WIKORA WBO 1005 UNO Technisches Dokument

WIKORA

WIKORA WBO 406 UNO Technisches Dokument

WIKORA

WIKORA WBO 120 TN Technisches Dokument

WIKORA

WIKORA WBO 1505 UNO Technisches Dokument

WIKORA

WIKORA WPH 300 Bedienungsanleitung

WIKORA

WIKORA WPS 805 Bedienungsanleitung

WIKORA

WIKORA WIKOSOL TWIN TRIVALENT Technisches Dokument

WIKORA

WIKORA WBO 405 UNO Technisches Dokument

WIKORA

WIKORA WBO 2005 UNO Technisches Dokument

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

Applimo

Applimo Edel AIR Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung