Wilson Electronics 460008 Bedienungsanleitung

Contents:

How it Works ...................................1

Before Getting Started............................2

Quick Installation Overview ........................2

Installing the Outside Antenna......................2

Installing the Low-Profile Antenna ...................3

Installing a Wilson Electronics Signal Booster. . . . . . . . . . 3

Powering Up a Wilson Electronics Signal Booster ......3

Understanding the Signal Booster Lights .............4

Warnings and Recommendations ...................4

Guarantee and Warranty ..........................6

Signal Booster Specifications ..............Back Cover

Note: This manual contains important safety and operating information.

Please read and follow the instructions in this manual. Failure to

do so could be hazardous and result in damage to your Signal

Booster.

Mobile 4G

Smart Technology ™

Signal Booster

Appearance of device and accessories may vary.

1 2

Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660

Or email: [email protected] Mon.- Fri. Hours: 7am to 6 pm MST.

Signal Booster

DC power supply

5V / 2.5A (859948)

How it Works

Your new Wilson Signal Booster has been carefully engineered to significantly improve the performance

of your cell phone and cellular data card in mobile applications. Together with an Outside Antenna, the

Signal Booster’s state-of-the-art technology is designed to increase your signal, reduce dropped calls

and increase data communication rates.

The Outside Antenna will collect the cell tower signal and send it through the cable to the Signal

Booster which is then boosted and sent to the Inside Antenna. Result – improved signal!

KIT CONFIGURATION

Wilson Electronics manufactures a wide variety of antennas to help you customize your Signal Booster for your specific application.

See your dealer or visit www.WilsonElectronics.com.

Installation Instructions for the Following Wilson Electronics Signal Boosters:

Mobile 4G Smart Technology ™Signal Booster

Model # 460008 FCC ID: PWO460008

INSIDE ANTENNA OPTIONS

OUTSIDE ANTENNA OPTIONS

311127 - Slim Low Profile w/ 10’ RG174

311106 - Low Profile w/ 10’ RG58

Mini-Mag

301126 w/ 12.5 RG174 cable- SMA

301113 w/ 12.5 RG174 cable - FME

12” Mag Mount

311103 w/ 12.5’ RG174

311125 w/ 12.5’ RG174

311128 w/ 12.5’ RG174

314202 w/ 12.5’ RG174

311703 w/ 12.5’ RG174

Trucker Antenna

311101 w/10.5’ RG58

311701 w/10.5’ RG58

Trucker Antenna

311119 w/13.5’ RG58

311133 w/13.5’ RG58

Marine Antenna

311130-5810 w/10.5’ RG58

Glass Mount

311102 w/14’ RG58

311114 w/14’ RG58

NMO Antenna

Kit 311104-5810

• 800/1900 NMO Antenna

• 10’ RG58 Cable

Kit 311112-5810

• 800/1900 NMO Antenna

• 10’ RG58 Cable

Kit 314203-5810

• 800/900/1900 NMO Antenna

• 10’ RG58 Cable

Kit 311112-40015

• 800/1900 NMO Antenna

• 15’ LMR400 cable

Kit 314203-40015

• 800/900/1900 NMO antenna

• 15’ LMR400 cable

Kit 311104-40015

• 800/1900 NMO Antenna

• 15’ LMR400 Cable

Kit 311104-17410

• 800/1900 NMO antenna

• 10’ RG174 cable

Kit 311112-17410

• 800/1900 NMO antenna

• 10’ RG174 cable

Kit 314203-17410

• 800/900/1900 NMO antenna

• 10’ RG174 cable

Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660

Or email: [email protected] Mon.- Fri. Hours: 7am to 6 pm MST.

Warning: In a wireless installation, do not

plug the Signal Booster directly into the cell

phone and/or data card using an antenna

adapter. It may damage the Signal Booster,

cell phone and/or data card.

Quick Installation Overview

Magnet - Mount

Antenna Shown

Part #301103

Carefully

Pull Down

Door Seal

Run Cable

Under Seal

Tuck Cable

Under Seal

Installing the Outside Antenna

To receive the best cell signal, select a location in the

center of the vehicle’s roof 12 inches away from any other

antennas or windows. If the vehicle has a sunroof, it is

important to separate the Inside and Outside Antennas by

at least five feet. This prevents the Signal Booster from

overloading or oscillating. As shown above. Follow the

specific antenna installation instructions included with the

Outside Antenna.

Separation of the Inside and Outside Antennas is very

important. The metal roof of the vehicle acts as a barrier

and helps shield the two antennas from each other,

preventing oscillation (feedback).

The Outside Antenna must be installed vertically. Signal

performance will be degraded if the antenna is not vertical.

The antenna cable may run through the door to the Signal

Booster.

For a more professional looking installation, run the

antenna cable under the door seal. The antenna cable is

small enough to easily tuck under the door seal or plastic

molding. Carefully pull down the door seal. Run the cable

through the seal and push the seal back into place. This

prevents constant wear and tear on the cable as the door

opens and closes.

Warning: Do not plug in the DC power

supply until the Outside and Inside

Antenna cables are attached to the Signal

Booster.

HUMMER

Installation Diagram

Outside

Antenna

Inside

Antenna

Distance between antennas

through a sunroof must be 5

feet or more.

DC Power

Supply

Signal

Booster

Cell Phone

PDA

Notebook

Before Getting Started

This guide will help you properly install your Wilson Electronics Five Band Mobile Wireless Signal

Booster. It is important to read through all of the installation steps for your particular application

prior to installing any equipment. Read through the instructions, visualize where all the equipment

will need to be installed and do a soft installation before mounting any equipment. Contact Wilson

Electronics Technical Support Team with any questions at 866-294-1660.

3 4

Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660

Or email: [email protected] Mon.- Fri. Hours: 7am to 6 pm MST.

Installing a Wilson Electronics Signal Booster

Warning: Do not install the Low-Profile Antenna within four

inches of metal. (Metal found inside the vehicle’s seat will not

affect the antenna’s performance.)

Signal Booster

Low-Profile

Antenna

Installing the Low-Profile Antenna

Warning: Do not plug in the DC power supply until the Outside

and Inside Antenna cables are attached to the Signal Booster.

Select a location to install the Signal Booster that is away from excessive heat, direct sunlight, moisture

and has proper ventilation.

Run the cable from the Outside Antenna and attach it to the connector labeled “Outside Antenna” on the

Signal Booster.

Attach the Low-Profile Antenna cable to the connector labeled “Inside Antenna” on the Signal Booster.

NOTE: The aluminum casing of a Wilson Signal Booster will adjust very quickly to the ambient

temperature of its environment. For example, in the summer, when the inside of a car can reach 140

degrees Fahrenheit, the Signal Booster temperature may be 150 degrees or higher. The casing will

be hot to the touch, similar to a metal door handle or a steering wheel. Such high temperatures will

not damage the Signal Booster, nor do they pose a fire risk to the vehicle. As recommended in these

instructions, install the Signal Booster in a location with adequate ventilation. Keep the area free of items

that could block air flow to the Signal Booster.

Connect the power cable from the DC plug-in power supply

to the Signal Booster marked “POWER” and insert the large

end into DC power socket (the vehicle power adapter outlet).

The Signal Booster may remain on all the time. However,

leaving the Signal Booster on in a vehicle when it is not

running can discharge or drain the battery in a day or two.

Switch the power supply off when not in use.

A good option is to power the Signal Booster through the

ignition switch so the Signal Booster is turned on and off with

the vehicle.

An available option to do this with is the Hardwire Kit from

Wilson Electronics (#859923).

IMPORTANT:

Do not power up the Signal Booster unless

antenna cables are attached to Signal Booster.

ON/OFF SWITCH

5 V DC / POWER

Powering up a Wilson Electronics Signal Booster

Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660

Or email: [email protected] Mon.- Fri. Hours: 7am to 6 pm MST.

If the indicator lights on the Signal Booster are green, the unit is powered up and working

properly.

If one or more lights on the Signal Booster are red, this indicates that the Signal Booster

has shut down on that frequency to prevent an oscillation (feedback). First, make sure that

all connections are tight. The Outside Antenna needs to be moved farther from the Inside

Antenna. Move the Outside Antenna on the roof of the car to the rear of the car, but at least

8-12 inches from the rear or side windows. Reset the Signal Booster by disconnecting then

reconnecting the power to the signal booster.

If one or more of the lights on the Signal Booster are blinking red, this means that the Signal

Booster has shutoff due to close proximity to the handset or mobile device. Increase the

distance between the handset and the Inside Antenna until the light is no longer flashing red.

Contact Wilson Electronics Technical Support Team for assistance.

Lights and Troubleshooting

This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation. Changes or modications not expressly

approved by Wilson Electronics could void the authority to operate this equipment.

Warnings and Recommendations

Warning: In a wireless installation, do not plug the Signal Booster directly into the cell phone or

cellular data card using an antenna adapter. It will damage the Signal Booster, cell

phone or cellular data card.

Warning: Do not plug in the DC power supply until the Outside and Inside Antenna cables are

attached to the Signal Booster.

Warning: The Inside Antennas must have 18 inches of separation distance from all active users.

Warning: RF Safety: Any antenna used with this device must be located at least 8 inches from

all persons and can be found on page 1 of the Install Guide.

Warning: Use only the power supply provided in this package. The power supply must be 6 V DC

Output.

Warning: The Outside Antenna must be installed no higher than 10 meters (32’9”) above ground.

Green:

Red:

Blinking

Red:

BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your

provider’s consent. Most wireless providers consent to the use of signal boosters. Some

providers may not consent to the use of this device on their network. If you are unsure, contact

your provider.

You MUST operate this device with approved antennas and cables as specified by the

manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person.

You MUST cease operating this device immediately if requested by the FCC or a licensed

wireless service provider.

WARNING. E911 location information may not be provided or may be inaccurate for calls served

by using this device.

This is a CONSUMER device.

5 6

Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660

Or email: [email protected] Mon.- Fri. Hours: 7am to 6 pm MST.

About Wilson Electronics

Wilson Electronics, LLC has been a leader in the wireless communications industry for over 40

years. The company designs and manufactures Signal Boosters, antennas and related components

that significantly improve cellular phone signal reception and transmission in a wide variety of

applications, mobile (vehicle, RV, marine) and in-building (home, office, machine to machine).

With extensive experience in antenna and Signal Booster research and design, the company’s

engineering team uses a state-of-the-art testing laboratory, including an anechoic chamber and

network analyzers, to fine-tune antenna designs and performance. For its Signal Boosters, Wilson

Electronics uses a double electrically shielded RF enclosure and cell tower simulators for compliance

testing.

Wilson Electronics Signal Boosters feature patent-pending Smart Technology ™ that enables them

to automatically adjust their power based on cell tower requirements. By detecting and preventing

oscillation (feedback), signal overload and interference with other users, these Smart Technology ™

Signal Boosters improve network cell phone areas without compromising carrier systems.

All products are engineered and assembled in the company’s 100,000 square-foot headquarters

in St. George, Utah. Wilson Electronics has product dealers in all 50 states as well as in countries

around the world.

Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660

Or email: [email protected] Mon.- Fri. Hours: 7am to 6 pm MST.

30-Day Money-Back Guarantee

All Wilson Electronics products are protected by Wilson Electronics 30-day money-back

guarantee. If for any reason the performance of any product is not acceptable, simply return the

product directly to the reseller with a dated proof of purchase.

2-Year Warranty

Wilson Electronics Signal Boosters are warranted for two (2) years against defects in

workmanship and/or materials. Warranty cases may be resolved by returning the product

directly to the reseller with a dated proof of purchase.

Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense,

with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied

by Wilson Electronics. Wilson Electronics shall, at its option, either repair or replace the product.

Wilson Electronics will pay for delivery of the repaired or replaced product back to the original

consumer within the continental U.S..

This warranty does not apply to any Signal Boosters determined by Wilson Electronics to have

been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or

electronic properties.

RMA numbers may be obtained by contacting Technical Support at 866-294-1660.

Disclaimer: The information provided by Wilson Electronics, LLC is believed to be complete and

accurate. However, no responsibility is assumed by Wilson Electronics, LLC for any business

or personal losses arising from its use, or for any infringements of patents or other rights of third

parties that may result from its use.

U.S. Patent Nos. – 7,221,967; 7,729,669; 7,486,929; 7,409,186; 7,783,318; 8,583,034; 8,583,033

111322_RevP_01.21.14

Wilson Electronics, LLC

3301 East Deseret Drive, St. George, UT 84790

For additional Technical Support visit www.WilsonElectronics.com

or email at: [email protected]

Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432

www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular

Signal Booster Specifications

Model Number 460008

Connectors SMA

Antenna Impedance 50 Ohms

Frequency 704-746 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz

3Power output for single cell phone (dBm) 700 MHz Band 17 700 MHz Band 13 800 MHz 1900 MHz 1700 MHz

Uplink 25.7 24.4 25.1 25.2 23.8

3Power output for single cell phone (dBm) 700 MHz Band 17 700 MHz Band 13 800 MHz 1900 MHz 2100 MHz

Downlink -4.3 -4.1 -1.2 4.0 5.6

Noise Figure (typical downlink/uplink) 3 dB nominal

Isolation > 90 dB

Power Requirements 5 V 2.5 A

Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the

hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster

is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the

Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1

minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing

power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor.

Inhaltsverzeichnis

Andere Wilson Electronics Extender Handbücher

Wilson Electronics

Wilson Electronics WilsonPro A500 Bedienungsanleitung

Wilson Electronics

Wilson Electronics PRO Series Bedienungsanleitung

Wilson Electronics

Wilson Electronics weboost DRIVE REACH OTR FLEET Bedienungsanleitung

Wilson Electronics

Wilson Electronics SLEEK 2B5225 Bedienungsanleitung

Wilson Electronics

Wilson Electronics 801105 Bedienungsanleitung

Wilson Electronics

Wilson Electronics iDEN 800 MHz 274080 Bedienungsanleitung

Wilson Electronics

Wilson Electronics AG Pro 75 Bedienungsanleitung

Wilson Electronics

Wilson Electronics WILSON PRO 1050 Bedienungsanleitung

Wilson Electronics

Wilson Electronics DB Pro 462105 Bedienungsanleitung

Wilson Electronics

Wilson Electronics Mobile 4G SmarTech III 460108 Bedienungsanleitung

Wilson Electronics

Wilson Electronics MobileMaxx 3G 460011 Bedienungsanleitung

Wilson Electronics

Wilson Electronics 801213 Bedienungsanleitung

Wilson Electronics

Wilson Electronics weBoost DRIVE X 475021R Bedienungsanleitung

Wilson Electronics

Wilson Electronics AG Pro 70 Bedienungsanleitung

Wilson Electronics

Wilson Electronics AG Pro 75 Bedienungsanleitung

Wilson Electronics

Wilson Electronics weboost Drive Reach OTR Installationsanleitung

Wilson Electronics

Wilson Electronics weBoost DRIVE 4G-X OTR 470210R Bedienungsanleitung

Wilson Electronics

Wilson Electronics Signal 3G Bedienungsanleitung

Wilson Electronics

Wilson Electronics Signal 4G SmarTech III Bedienungsanleitung

Wilson Electronics

Wilson Electronics weboost 472061 Bedienungsanleitung

Wilson Electronics

Wilson Electronics Sleek Bedienungsanleitung

Wilson Electronics

Wilson Electronics SIGNALBOOST 811210 Bedienungsanleitung

Wilson Electronics

Wilson Electronics AG Pro Quint 461104 Bedienungsanleitung

Wilson Electronics

Wilson Electronics WilsonPro A1000 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung