Winegard Carryout Bedienungsanleitung

Quick Start Guide

For up-to-date information on receiver compatibility

and programming, visit www.winegard.com/receivers

Before using your Carryout®antenna, there may be some initial steps

required to set up your Carryout antenna for use with your receiver. This

is a one-time process. Follow the steps here for a typical installation. If

you have additional questions, consult the full Users Manual.

1)Programming the Carryout Antenna

The Carryout antenna comes factory pre-set for DIRECTV®.

DISH®users should follow the steps shown below.

DIRECTV users can skip to Wiring the Carryout Antenna.

First you’ll need to identify

the electronics box on

the Carryout antenna.

After removing the dome,

you will find the main

electronics housing

located directly behind the

reflector.

On the side of the electronics board, you will see dip-switches that control

what service provider the Carryout antenna is set for. It is factory pre-set for

DIRECTV with

the 8th switch

down.

Factory pre-set for DIRECTV

DISH settings

To set for DISH,

push the 4th

and 7th switches down,

and leave the 8th down.

There are additional switch options shown in the Carryout manual

for alternate DISH settings or Bell TV™settings.

Connect the supplied power cable

to the quick disconnect socket.

Connect a coax cable from the

primary receiver to the main port.

If applicable, connect a second

coax cable from the secondary

receiver to the secondary port.

The coaxial cable needs to run

DIRECTLY from the Satellite In

port on the back of the Satellite

Receiver. If wiring through a wall plate

on the side of the coach, consult

Using Outside Receptacle

steps on back.

2)Wiring the Carryout Antenna

Before plugging in power, be sure that your satellite receiver is set up

for use with the Carryout antenna, as shown inside this guide.

The power plug needs to be

connected to a 12V power source

- or -

connect to an AC to DC

power converter

(like GM-1200 below).

Then, plug converter

into 110V outlet.

If using a Power Converter, it must be able to supply up to 5 amps of current.

Front

Back

Carryout

plug

Press Menu on

your remote.

Select option 6,

System Setup.

Select option 1,

Installation.

Select option 1,

Point Dish.

Select Check

Switch.

With the antenna still

turned off, select Test.

It will go through a number

of steps, then return to

the screen shown here

with previous information

cleared. If at any point it

asks you to save, select

Save or Yes.

Next, select Test again.

This time it will install the

proper switch for use with

the Carryout antenna. Once

the steps are complete, you

will see a similar screen to

what is shown to the right.

The wording and look used

in your receiver may differ

slightly. Press Menu, then

select Parental, Fav’s &

Setup.

Then select

System Setup.

In your Receiver’s Menu,

you will need to identify

the Satellite Menu.

Once there, find the option

for Satellite Setup.

Select the option for

3 LNBs or 3 Satellites.

If given the option of

SWM or Multiswitch,

select Multiswitch.

The receiver will

automatically verify

your setup.

You may see errors

for certain satellites

during this step, but

that is normal.

DISH Receiver Setup DIRECTV Receiver Setup

BEFORE turning the antenna on, follow the steps

below to clear any existing receiver settings.

Now turn on the Carryout antenna. Allow it 3–4 minutes to acquire satellites.

When you see SW64 as the Installed Switch, the Carryout antenna is ready for use. The Carryout antenna is now ready for use.

Check out online receiver setup guides for your antenna at

www.winegard.com/receivers/setupguide.php.

Plug in the antenna and allow it a few minutes to acquire

the satellites. Then, follow the steps shown below.

Check out online receiver setup guides for your antenna at

www.winegard.com/receivers/setupguide.php.

www.winegard.com

Technical Service: 1-800-788-4417

For up-to-date information on receiver compatibility

and programming, visit www.winegard.com/receivers

Winegard and Carryout are registered trademarks of Winegard Company. DISH is a registered trademark of DISH Network L.L.C.

DIRECTV is a registered trademark of DIRECTV, Inc., a unit of Hughes Electronics Corp. Bell TV is a registered trademark of Bell Canada, Inc.

Using Outside Receptacle

Cable

If your outside TV receptacle is wired for satellite, locate where the oustide

receptacle leads to in your RV, and connect

your satellite receiver directly to this

corresponding inside receptacle.

If the outside TV receptacle is wired for

cable, the wiring will have to be modified

for use with satellite. The coaxial cable

cannot run through any other devices or

switches BEFORE the satellite receiver.

Typically, if wired for cable, the wiring will either run through a Winegard

power supply or video switch. The easiest way to fix this is to disconnect the

cable from that device, use a barrel connector, and connect a new cable that

runs directly to the receiver, bypassing the power supply or video switch.

TIP: If experiencing problems, connect the Carryout coaxial cable directly to the receiver by

running the cable through your RV door to ensure the antenna is running properly.

Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000

800/788-4417 • FAX 319/754-0787 • www.winegard.com

Video Switch Video Switch AFTERBEFORE

2452172

www.winegard.com

For Technical Services, call 1-800-788-4417

For Receivers and Programming, call 1-866-609-9374

DO NOT RETURN ANTENNA TO PLACE OF PURCHASE.

For up-to-date information on receiver compatibility and

programming, visit www.winegard.com/receivers

Product Registration

Please register your Winegard product by filling out and returning

the Product Registration Card provided or by completing the online

registration form at http://www.winegard.com/registration.

Trademarks

Disclaimer

Safety Recommendations

Models

Specifications

Carryout Antenna 2

1 Carryout Antenna

Do not paint this antenna. Painting the antenna will void your warranty.

The Carryout antenna is meant for stationary use only and will not function

while in motion. The Carryout antenna is not intended for permanent

mounting on a commercial vehicle.

While the Carryout antenna is designed with Winegard’s focus on quality

and durability in mind, it is still an electronic device, and care should be

taken when transporting and setting up the Carryout antenna. Do not toss

or drop the Carryout antenna.

Winegard and Carryout are registered trademarks of Winegard Company. DISH is

a registered trademark of DISH Network L.L.C. DIRECTV is a registered trademark

of DIRECTV, Inc., a unit of Hughes Electronics Corp. Bell TV is a trademark of Bell

Canada, Inc. Reference made to products or services provided by companies,

other than Winegard Company, does not represent any endorsement of those

products or services.

Although every effort has been made to ensure that the information in this manual

is correct and complete, no company shall be held liable for any errors or omissions

in this manual. Changes and technological advances are continuously being made

in the satellite market. Information provided in this manual was accurate at time

of printing. If the Carryout antenna does not function as expected, please contact

Winegard Company at 1-800-788-4417, or visit our website at www.winegard.com.

Dome

•One button operation

•Supports up to two receivers

•Depending on receiver type and

location, can access the following

satellites:

DISH®Western Arc:

110°, 119°, 129°

DISH Hybrid:

110°, 119°, 61.5°

DISH Eastern Arc:

61.5°, 72°, 77°

DIRECTV®:119° or 101° (will not receive

HD on 110° or any KA-band HD on 99° and 103°)

Bell TV™:91° or 82°

•Gray plastic base

•Elevation range 20° to 92°

•Azimuth +360° (0-692°)

•UV-protected plastic dome

•Compact size

20” diameter, 15.6” height

Shipping size: 23” x 23” x 17¾”

•Operating temperature: -13° F to

+140° F

•Specifications for max amperage:

5.0 A

•Specifications for unit operating

voltage: 10.5–13.8 V

•Specifications for supply voltage:

12–13.8 V

Base

GM-1518, CB-1518 (white dome) GM-1599, CB-1599 (camouflage dome)

Switch Settings

The Carryout antenna switch settings are preset for DIRECTV. To set the antenna

for any other programming provider, remove the dome and set the switches

according to the appropriate diagram below. Otherwise, proceed to “Installing the

Carryout Handle” on the next page.

Hybrid mode is for use in areas where the 129° satellite is not available.

Eyelet

Handle

DISH Hybrid



    



1 2 3 4 5 6 7 8

Bell TV



1 2 3 4 5 6 7 8

DIRECTV

  

1 2 3 4 5 6 7 8

0= Up

1= Down

Key



DISH





1 2 3 4 5 6 7 8

3 Carryout Antenna Carryout Antenna 4

Installing the Dome

Installing the Carryout Handle

Selecting a Location for the Carryout

Connecting the Power

Connecting the Cables

Plug the power cord into the quick disconnect socket in the Carryout base. Make

sure that the lock ‘clicks’ when you plug the cord in. This will ensure a good

connection.

Connect coax to the main connection on the base of the antenna. Do not use a

wrench to tighten the cable. The coax provided uses weatherproof connectors,

which can be damaged if over-tightened.

If you have changed the switch settings under the dome, you will need to re-install

the dome. Place the Carryout Dome over the unit so that the Carryout decal on the

Dome is directly above the connections on the base of the unit. Line up the holes

in the dome with the inserts in the Carryout base. Insert all of the dome screws

except the two nearest to the cable connections on the base. Do not tighten the

screws at this time. Continue with “Installing the Carryout Handle” below.

If you have changed the switch settings under the dome, install the Carryout

handle by threading two screws through the handle and then through the two

holes nearest the cable connections on the base. Installing the handle here will

help protect the cable connections from accidental damage.

If using DIRECTV, simply remove the two screws nearest the coax and power

connectors on the base and use these screws to install the handle.

Tighten all of the dome screws using a Phillips screwdriver.

Try to find a location that is fairly level and has a clear view of the southern sky.

The location should provide a stable enough surface to keep the Carryout from

falling over during use, and the surface must be ±5° of level.

Other things to consider when choosing a location for the Carryout are traffic

patterns and the weather. Placing the Carryout near a walking path may cause

people to trip over the cables or knock the Carryout off of the signal.

TIP The Carryout antenna comes with 50’ of cable. Keep this in mind when

selecting a location.

NOTE If the receiver is used for DIRECTV HD programming at home, make sure

that the B-Band converter has been removed prior to connecting the

Carryout antenna.

The Carryout antenna comes with two coax ports set in the base. The MAIN

port will control the toggle function and should always be connected when the

Carryout antenna is in use. This cable should run to the “Sat In” port on the back

of the receiver that will be used most often.

Once the Carryout antenna is connected to your receiver, you can plug it into a

12 V Cigarette plug outlet in your vehicle or a 120 V to 12 VDC converter with a

cigarette style outlet.

When connecting the Carryout antenna, Winegard recommends using a 120 V

to 12 VDC power converter or 12 VDC power source that meets power supply

specifications.

Before turning the Carryout antenna on, refer to “DISH Receiver Setup” on page 5

or “DIRECTV Receiver Setup” on page 11.

Main Port

Secondary Port

Quick

Disconnect

Socket

MAIN SEC

Carryout Antenna 6

5 Carryout Antenna

DISH Receiver Setup DISH Receiver Setup

Select Test.

It will go through a number of

steps, then return to the screen

shown here with previous

information cleared.

If at any point it asks you to save,

select Save or Yes.

Reconnect the coaxial cable to the “Sat In” port on back of receiver. Now turn on

the antenna. Allow it 3–4 minutes to acquire satellites.

If setting up a DISH 311, 301, or 500 series receiver, in some cases you may need

to check the boxes next to Superdish and Alternate before running the Check

Switch test. Then, select Test and continue with normal receiver setup.

Select option 1, Point Dish.

Before turning the Carryout antenna on, follow the steps

below to clear out any existing receiver settings. If your

receiver differs from the options shown, you may need to

consult your receiver manual. The wording and display used

in your receiver may differ slightly.

For help, call 1-800-788-4417

Before starting, disconnect coax

cable from “Sat In” on back of

receiver. Press Menu on your

remote. Select option 6, System

Setup.

Select option 1, Installation.

Disclaimer: Receiver setup instructions are accurate at time of printing and may change without

notice. Call Winegard tech line for assistance: 1-800-788-4417.

Select Check Switch.

Check that there are no

checkmarks by SuperDISH or

Alternate.

Next, select Test again.

This time it will install the

SW64 switch. This SW64 switch

is a DISH receiver setting, not a

physical part.

When you see the SW64 as the

installed switch, the antenna is ready for use.

SW64

Carryout Antenna 8

7 Carryout Antenna

Receiver Recommendations

DISH Satellite Coverage

DISH Satellite Coverage, Cont.

DISH Eastern Arc

The Carryout antenna will operate with most DISH receivers. Winegard does

not recommend using receivers with hard drives not recommended by the

manufacturer for mobile applications. Winegard recommends using a single

tuner DISH receiver.

The antenna will locate and toggle between satellites 110°, 119° and 129° in

Western Arc Mode. The Carryout antenna will not operate in all areas where

satellites 110°, 119° and 129° are available.

The antenna will locate and toggle between satellites 110°, 119° and 61.5° in

Hybrid mode. The antenna will not operate in all areas where satellites 110°, 119°

and 61.5° are available.

Satellite coverage maps are based on level, stationary operation. Reception

interruption may also occur during adverse weather conditions.

DISH satellites 110° &119° coverage map

(Dotted area indicates coverage.)

Coverage maps are for reference only and do not guarantee coverage.

DISH satellite 61.5° &129° coverage map

Hybrid mode is for use with DISH in the Northeast where the 129° satellite is not

available. If neither DISH Western Arc nor DISH Hybrid Mode will provide an HD

signal, then the Eastern Arc may be used.

Consult the map above. If you are in the 61.5° coverage area, use the DISH

Eastern Arc. See switch settings below.

DISH satellite 61.5°

Carryout antenna coverage map

DISH satellite 129°

Carryout antenna coverage map



DISH Eastern Arc

 

1 2 3 4 5 6 7 8





Carryout Antenna 10

9 Carryout Antenna

DIRECTV Receiver Setup

If your receiver differs from the options shown, you may

need to consult your receiver manual. The wording and

display used in your receiver may differ slightly.

For more information on receiver compatibility and

programming, visit www.winegard.com/receivers.

For help, call 1-800-788-4417

DIRECTV Receiver Setup

Disclaimer: Receiver setup instructions are accurate at time of printing and may change without

notice. Call Winegard tech line for assistance: 1-800-788-4417.

Select 3-LNB (18”x20”) or 3

Satellites. If given the option

of SWM or Multi-switch, select

Multiswitch.

Now power on the Carryout

antenna, and allow it a few

minutes to acquire signal.

If you want to check signal strengths, choose Signal Strength from the menu

options before returning to this screen.

Now, press Continue.

In your receiver menu, you will

need to identify the Satellite

Menu. Once there, find the

option for Satellite Setup.

Press Menu on your remote,

and then select Parental, Fav’s &

Setup.

Select System Setup.

After pressing Continue, the

receiver will automatically verify

your setup.

You may be required to press the

DASH (-) before proceeding

(underneath #7 on the remote).

Continue with step 7 on the next page.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Winegard Antenne Handbücher

Winegard

Winegard RoadTrip SD Bedienungsanleitung

Winegard

Winegard DS-4248 Bedienungsanleitung

Winegard

Winegard Movin' View MV-1111 Bedienungsanleitung

Winegard

Winegard HD7698 Bedienungsanleitung

Winegard

Winegard Pathway X1 Bedienungsanleitung

Winegard

Winegard RD-9046 Bedienungsanleitung

Winegard

Winegard A3-2000 Betriebsanleitung

Winegard

Winegard RZ-6035 Bedienungsanleitung

Winegard

Winegard MM-3084 Bedienungsanleitung

Winegard

Winegard Trav'ler Bedienungsanleitung

Winegard

Winegard TRAV'LER Series Bedienungsanleitung

Winegard

Winegard Sensar HV CC-10HV Bedienungsanleitung

Winegard

Winegard TR-6018 Bedienungsanleitung

Winegard

Winegard HD7694 Bedienungsanleitung

Winegard

Winegard PR-8800 Bedienungsanleitung

Winegard

Winegard SENSAR III ANTENNA Bedienungsanleitung

Winegard

Winegard HD9065P Bedienungsanleitung

Winegard

Winegard In-Motion MVT-35W Bedienungsanleitung

Winegard

Winegard FlatWave Micro Bedienungsanleitung

Winegard

Winegard TRAV'LER DIRECTV SK-SWM3 Bedienungsanleitung

Winegard

Winegard HD7082P Bedienungsanleitung

Winegard

Winegard HD7000R Bedienungsanleitung

Winegard

Winegard Sensar HV CC-25HV Bedienungsanleitung

Winegard

Winegard TRAV’LER DISH 1000 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung