Winmate FM08 Bedienungsanleitung
Winmate FM08
Vehicle Mounted Computer
Microsoft ®Windows ®7 Professional for Embedded System
Microsoft ®Windows ®Embedded 8.1 Industry Pro
Quick Start Guide
1
FM08 Quick Start Guide
About This Guide
This guide contains the following:
Contents
About This Guide 1
i. Features 2
ii. Unpacking 3
iii. Docking and Undocking the Device 4
a. Dock the device into vehicle dock 4
b. Undock the device 4
iv. Cabling Installation 5
a. Connecting the power cable for office testing 5
b. Connecting the power cable on the vehicle 6
v. Power On Behavior 8
a. Power Button 9
b. Standby / Wakeup Behavior 9
vi. Defroster 10
vii. Antenna Installation 12
viii. RAM Mounts Installation 13
a. Component of RAM Mounts kits 13
b. RAM Mounts assembly 13
c. Keyboard Mounting Installation 14
For more detail information about this device, please refer to the FM08 User Manual available at
http://www.winmate.com/
2
FM08 Quick Start Guide
i. Features
3
FM08 Quick Start Guide
ii. Unpacking
Computer FM08
Dock with latch locking key
Power cable (5 m) with 2 x fuse kit
USB Cable (0.3 m)
Stylus Kit with Screw
Cable clamp kit
2 x WiFi External Antenna
Quick Start Guide and Driver CD
Power cable for Testing*
4
FM08 Quick Start Guide
Note
Users are highly recommended to purchase this power cable for
testing purpose
iii. Docking and Undocking the Device
a.Dock the device into vehicle dock
To dock the device, perform the following:
1. With the device screen side facing out, align and insert the device into the guide pins on
the vehicle dock.
2. Push the device against the dock to ensure the terminal contacts are properly connected.
3. Secure the device by pulling the latch forward until a “click” is heard, indicating the latch is
fully engaged.
b.Undock the device
To undock the device from the vehicle dock, perform the following:
1. While supporting the device with one hand, push the latch backward until it fully
disengaged.
2. Remove the device from the vehicle dock.
1.
2.
3.
1.
2.
5
FM08 Quick Start Guide
iv. Cabling Installation
Warning
This procedure require a trained service personnel only,
improper installation can cause serious damage to the vehicle
or the device
a.Connecting the power cable for office testing
Note
Users are highly recommended to purchase this power cable for
testing purpose
1. Place the device on the vehicle dock and make sure the device is Off
2. Connect the CN2 to the FM08 vehicle dock by aligning the connector pins and then push it,
twist to fasten the connection.
3. Connect the AC plug to the electrical outlet
* The Positive (+) and Ignition is
connected inside the cable
6
FM08 Quick Start Guide
4. Switch the power switch On, located on the back of the vehicle dock
5. Press the On button, the device is ready for testing
b.Connecting the power cable on the vehicle
Warning
This power cable should only be used on the 12, 24, 36, or 48
Volt forklifts.
Warning
Select a mounting location and make sure it is not located on
the outside the vehicle
Color
Symbol
Red
VCC+
Black
VCC-
Green
Ground
Blue
Ignition input (optional)
Warning
Do not perform the installation on a moving or live electric
forklift
1. Remove the vehicle battery before connecting the power cable
2. Connect the Green Wire (Ground) to the vehicle‟s chassis (grounding), which can also
be negative pole of the battery. See diagram 6-1 and 6-2
3. Place the fuse and fuse holder in-line of the Red (VCC +) and Blue (ignition) wires as
shown below.
7
FM08 Quick Start Guide
Fuse Specification :
Two Fuses , 15A, 250Volt, UDA Type Fuses
Warning
All power wiring must use the supplied power cable
4. Slide tubing over wires , remove the wires and insert it to the fuse holder, crimp it
5. Connect the red wire to the vehicle‟s positive power source. Connect the black wire to
the vehicle‟s negative power source.
6.1Connect the blue wire to the vehicle‟s ignition switch for the ignition function
Diagram 6.1 With Ignition Function
6.2The ignition cable (Blue cable) must be connected to the battery positive if the
customer does not want to have ignition function , as following
Diagram 6.2 Without Ignition Function
8
FM08 Quick Start Guide
7 Secure the power cable to the device using cable clamps and place the device in the dock.
See Power cable routing below
Warning
Use the proper cable clamps and not to over tighten it to
prevent it from break
8 Press the power switch on the back of the dock See Power switch
9 Press the power button on the front of the device See Power Button
v. Power On Behavior
The Following table shows the Ignition control power scheme on the vehicle installation and
office test.
Power On
Behavior
Office Test / Evaluation
Vehicle Installation
With Ignition
Without Ignition
Ignition delay
Default „”0 second”
Default „”0 second”
Default „”0 second”
Adjustable from 0-120 Second, through AP. See AP for Ignition below
Auto-ON
OFF, can be disable
through BIOS Switch
ON
ON
Power Button
√
X
X
9
FM08 Quick Start Guide
AP for Ignition Delay
a.Power Button
The Power button is located at lower right of
the FM08
Note
• The FM08 need to be docked in a powered
vehicle dock or UPS battery has a sufficient
charge to power the device.
• If no external power available and the UPS
battery does not have enough charge,
pressing the power button will cause no
action
Action
Button
Power Button
Backlight
Indicator
Turn On
Press the On button for “2 seconds”
until the battery indicator On (solid
green) and then release the button
Off
b.Standby / Wakeup Behavior
Andere Handbücher für FM08
2
Inhaltsverzeichnis
Andere Winmate Autozubehör Handbücher
Winmate
Winmate FM10Q Bedienungsanleitung
Winmate
Winmate FM10Q Installations- und Betriebshandbuch
Winmate
Winmate FM08 Installations- und Betriebshandbuch
Winmate
Winmate FM10A Installations- und Betriebshandbuch
Winmate
Winmate G-WIN Bedienungsanleitung
Winmate
Winmate FM08 Bedienungsanleitung
Winmate
Winmate FM07A Bedienungsanleitung
Winmate
Winmate FM07 Bedienungsanleitung
Winmate
Winmate FM10 Installations- und Betriebshandbuch
Winmate
Winmate FM10 Bedienungsanleitung
