Winmate W05TA3S-PCT3 Bedienungsanleitung
5" Access Control System
W05TA3S-PCT3
User Manual V1.0
FCC Statement
This device complies with part 15 FCC rules. Operation is subject to the
following two conditions：
This device may not cause harmful interference.
This device must accept any interference received including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a class "a" digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at him own expense.
Copyright Notice
ALL RIGHTS RESERVED. No part of this document may be reproduced, copied, translated, or
transmitted in any form or by any means, electronic or mechanical, for any purpose, without
the prior written permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective
owners.
Disclaimer
We reserve the right to make changes, without notice, to any product, including circuits
and/or software described or contained in this manual in order to improve design and/or
performance. We assume no responsibility or liability for the use of the described product(s),
conveys no license or title under any patent, copyright, or masks work rights to these
products, and makes no representations or warranties that these products are free from
patent, copyright, or mask work right infringement, unless otherwise specified. Applications
that are described in this manual are for illustration purposes only. We make no
representation or warranty that such application will be suitable for the specified use
without further testing or modification.
Warranty
We warrant that each of its products will be free from material and workmanship defects for
a period of one year from the invoice date. If the customer discovers a defect, We will, at its
option, repair or replace the defective product at no charge to the customer, provided it is
returned during the warranty period of one year, with transportation charges prepaid. The
returned product must be properly packaged in it’s original packaging to obtain warranty
service.
If the serial number and the product shipping data differ by over 30 days, the in-warranty
service will be made according to the shipping date. In the serial numbers the third and
fourth two digits give the year of manufacture, and the fifth digit means the month (e. g.,
with A for October, B for November and C for December).
For example, the serial number 1W07Axxxxxxxx means June of year 2009.
Customer Service
We provide service guide for any problem as follow steps. The first, contact with your
distributor, sales representative, or our customer service center for technical support if you
need additional assistance. You may have the following information ready before you call：
Product serial number
Peripheral attachments
Software (OS, version, application software, etc.)
Description of complete problem
The exact wording of any error messages
In addition, free technical support is available from our engineers every business day. We are
always ready to give advice on application requirements or specific information on the
installation and operation of any of our products. Please do not hesitate to call or e-mail us.
Manufacturer：WinMate Communication Inc.
Address： 9F, Number 111-6, Shin-De Rd., San-Chung City, Taipei 241, Taiwan, R.O.C.
TEL：+886-2-8511-0288
FAX：+886-2-8511-1108
Safety Information
WARNING!
Always completely disconnect the power cord from your chassis whenever you
work
with the hardware. Do not make connections while the power is on.
Sensitive electronic components can be damaged by sudden power surges.
Only
experienced electronics personnel should open the PC chassis.
Caution!
Always ground yourself to remove any static charge before touching the CPU card.
Modern
electronic devices are very sensitive to static electric charges. As a safety
precaution, use a
grounding wrist strap at all times. Place all electronic components
in a static-dissipative
surface or static-shielded bag when they are not in the chassis.
Safety Precautions
•
Please read these safety instructions carefully.
•
Please keep this user’s manual for later reference.
•
Please disconnect this equipment from any AC outlet before cleaning. Do not
use liquid or spray detergents for cleaning. Use a damp cloth.
•
Do not touch the LCD panel surface with sharp or hard objects.
•
For pluggable equipment, the power outlet must be installed near
the
equipment and must be easily accessible.
•
Keep this equipment away from humidity.
•
Place this equipment on a reliable surface during installation. Dropping it or
letting it fall could cause damage.
•
The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
•
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
•
Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
•
All cautions and warnings on the equipment should be noted.
•
If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient over-voltage.
•
Never pour any liquid into an opening. This could cause fire or electrical shock.
•
Never open the equipment. For safety reasons, only qualified service personnel
should open the equipment.
•
If any of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the
user’s manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
•
Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -20°C (-4°F) or above 60°C (140°F). It may damage the
equipment.
•
Caution – Use recommended mounting apparatus to avoid risk of injury.
•
WARNING – Only use the connection cords which comes along with the
product, when in doubt, please contact the manufacturer.
•
Provision shall be made to provide transient protection device to be set at a
level
not exceeding 140% of the rated voltage at the power supply terminals of
the
apparatus.
•
WARNING – Explosion Hazard – Do not disconnect equipment unless power has
been switched off or the area is known to be non-hazardous.
•
WARNING – The equipment should be adequately protected from direct light
when installed indoor or outdoor.
•
WARNING – DO NOT OPEN, MAINTAIN OR SERVICE IN AN AREA WHERE AN
EXPLOSIVE ATMOSPHERE MAY BE PRESENT.
Contents
Chapter1: Product Specification ....................................................................................... 2
1.1 Product Specification ................................................................................................... 3
1.2 RFID Reader Specification ........................................................................................... 4
1.3 Accessories .................................................................................................................. 5
Chapter2: Product Drawing & Dimension ......................................................................... 6
2.1 Product Overview ......................................................................................................... 7
2.2 Product Dimension ....................................................................................................... 8
Chapter3: First Operating ................................................................................................ 10
3.1 Turn on the Device ..................................................................................................... 11
3.1 Turn ooff the Device ................................................................................................... 11
3.3 System Block diagram ............................................................................................... 12
2
Users Manual
5” ACCESS Control
Chapter 1 Product Specification
C H A P T E R
1
3
Users Manual
5” ACCESS Control
1.1 Product Specification
Display Spec
Screen Size 5” LED backlight panel
Resolution 800 x 480
Brightness 300 nit
Contrast 500 : 1
Viewing Angle -70~70(H),-50~70(V)
Touch Screen
Projected Capacitive
Hardware Specification
CPU TI Cortex A8 AM3354 1GHz with DSP
RAM 1 x DDR2 533(Default 512 MB, Max 1GB)
LAN / PoE 1 x RJ45 10/100/1000 Mpbs
(Support PoE function IEEE 802.3AT)
Graphic PowerVR SGX 3D Gfx
Storage 1GB 8bit Nand Flash(OS)
1 x 8G Micro SD Card Slot(Compatible with SDHC)
Peripheral
Digital I/O 2 x Digital in, 2 x Digital out (Phoenix Type)
LAN 1 x RJ45
USB Ports 1 x USB Type-A Receptacle
Video 1 x 2MP camera module
1 x MIC in
Motion Sensor 1 x Proximity Sensor support 80cm(MAX)
Power input 1 x 12V DC IN (Phoenix Type)
PoE with IEEE 802.3AT(25W)
Power Consumption 10W (Full Loading)
Operating
Temperature
0°C ~ 55°C
Operating System Android 4.2
4
Users Manual
5” ACCESS Control
1.2 RFID Reader Specification
Andere Winmate IP-Zugriffskontrollsysteme Handbücher
