Witter F161U Bedienungsanleitung

# N A M E ?

W0001F161U-FIT$010802220000

Fitting

Instructions

TOWBAR

FOR Ford B-Max

2012-

F161U

MATERIALS

A 1 Cross Bar

B 2 Side Arm

C 4 M12 x 35 x 1.75 pitch Bolts, Lock Washers, Flat Washers (OD 30mm) and Witter Cage Nuts

D 4 M12 x 35 x 1.75 pitch Bolts and Serrated Flanged Nuts

E 2 M8 x 1.25 pitch Spigot Nuts and M10 Flat Washers

ZE 1 Retractable Electrical Plate

ZN 1 Neck Kit (3008 Series)

Note: This tow bar must be used with either a Witter Neck Kit (Series 3008) or Class A50-1 or A50-X tow ball, which dimensionally

conforms to A50-1 with a ‘D’ and 'S' value greater than or equal to that of the tow bar.

FITTING

1. Remove Bumper

2. Remove Steel Bumper Beam

3. Pre-assemble Witter Cage Nuts (C) to Side Arms (B) using separate Fitting Instructions. (Note the side to assemble to

as shown below)

4. Assemble Side Arms (B) into each Chassis rail and secure using fasteners (C)

5. Assemble Cross Bar (A) to the vehicle rear panel over the existing Steel Bumper Beam studs and so that the Side Arms

(B) protrude through the rectangular holes in the Cross Bar end plates.

6. Loosely secure to the vehicle using fasteners (E). (Note M10 washers fit over the spigot on M8 Nuts)

7. Loosely secure the protruding Side Arms (B) to the Cross Bar (A) using fasteners (D)

8. Assemble the chosen Neck Kit (ZN) and Retractable Electrical Kit (ZE) to Cross Bar (A) using separate instructions.

9. Fully tighten all fasteners

10. Refit bumper.

Recommended torque settings:

Grade 8.8 bolts: M8 - 24Nm, M10 - 52 Nm, M12 - 80 Nm, M14 - 130 Nm, M16 - 200 Nm

Grade 10.9: M12 –120Nm, M10 –70Nm M8- 35Nm

Notice de

Montage

ATTELAGE

Pour Ford B-Max

2012-

F161U

MATERIELS

A 1 Cross Bar Traverse principale

B 2 Side Arm Bras lateraux

C 4 M12 x 35 x 1.75 pitch Bolts, Lock Washers, Flat Washers (OD 30mm) and Witter Cage Nuts

D 4 M12 x 35 x 1.75 pitch Bolts and Serrated Flanged Nuts

E 2 M8 x 1.25 pitch Spigot Nuts and M10 Flat Washers

ZE 1 Retractable Electrical Plate

ZN 1 Neck Kit (3008 Series)

Note: This tow bar must be used with either a Witter Neck Kit (Series 3008) or Class A50-1 or A50-X tow ball, which dimensionally

conforms to A50-1 with a ‘D’ and 'S' value greater than or equal to that of the tow bar.

FITTING

11. Remove Bumper

12. Remove Steel Bumper Beam

13. Pre-assemble Witter Cage Nuts (C) to Side Arms (B) using separate Fitting Instructions. (Note the side to assemble to

as shown below)

14. Assemble Side Arms (B) into each Chassis rail and secure using fasteners (C)

15. Assemble Cross Bar (A) to the vehicle rear panel over the existing Steel Bumper Beam studs and so that the Side Arms

(B) protrude through the rectangular holes in the Cross Bar end plates.

16. Loosely secure to the vehicle using fasteners (E). (Note M10 washers fit over the spigot on M8 Nuts)

17. Loosely secure the protruding Side Arms (B) to the Cross Bar (A) using fasteners (D)

18. Assemble the chosen Neck Kit (ZN) and Retractable Electrical Kit (ZE) to Cross Bar (A) using separate instructions.

19. Fully tighten all fasteners

20. Cut bumper using the diagram below as a guide and refit to vehicle.

Recommended torque settings:

Grade 8.8 bolts: M8 - 24Nm, M10 - 52 Nm, M12 - 80 Nm, M14 - 130 Nm, M16 - 200 Nm

Grade 10.9: M12 –120Nm, M10 –70Nm M8- 35Nm

Inhaltsverzeichnis

Andere Witter Autozubehör Handbücher

Witter

Witter DT144AU Bedienungsanleitung

Witter

Witter FT74AU Bedienungsanleitung

Witter

Witter HY55U Bedienungsanleitung

Witter

Witter VW93 Bedienungsanleitung

Witter

Witter VW48C Bedienungsanleitung

Witter

Witter F181AU Installationsanleitung

Witter

Witter F105A Bedienungsanleitung

Witter

Witter F129AU Bedienungsanleitung

Witter

Witter KA47U Bedienungsanleitung

Witter

Witter F99CU Bedienungsanleitung

Witter

Witter CL114BU Bedienungsanleitung

Witter

Witter G125U Bedienungsanleitung

Witter

Witter F125U Bedienungsanleitung

Witter

Witter ZX302/EU Bedienungsanleitung

Witter

Witter F159 Installationsanleitung

Witter

Witter RN89 Installationsanleitung

Witter

Witter HY29B Bedienungsanleitung

Witter

Witter F177U Bedienungsanleitung

Witter

Witter RN117U Bedienungsanleitung

Witter

Witter ZX702 Bedienungsanleitung

Witter

Witter VW82U Installationsanleitung

Witter

Witter F166U Bedienungsanleitung

Witter

Witter F177U Bedienungsanleitung

Witter

Witter SK29U Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung