Wren TOWER UNIT Bedienungsanleitung

2070 x 600

600 + 450 Appliance

2250 x 600 Tall

600 + 450 Appliance

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Assembly Guide

BEFORE YOU START

INSTALLATION

SHOULD BE

PERFORMED BY A

COMPETENT

PERSON ONLY.

THIS PRODUCT COULD

BE DANGEROUS

IF INCORRECTLY

INSTALLED

REQUIRED TOOLS

NOT to be used

with CAM DOWEL

& CAM LOCK

DRAWER

COVER

CAP

DRAWER SIDE

x1 Right Hand

DRAWER SIDE

x1 Left Hand

DRAWER

FRONT

FIXING

x 2

Deep Drawer (Packed Separately)

Fitting Pack Contents

(Y) x2

Gallery

Head

(J) x16

Drawer Runner

16mm Screws

(N) x1

Door Buer

(Q) x4

21mm

Screw

(L) x2

15mm

Screw

METAL BACK PANEL

x 1

DRAWER

BASE

x 1

DRAWER RUNNER

x 1 Right Hand

FRONTAL

(Supplied separately)

DRAWER RUNNER

x 1 Left Hand

GALLERY

RAIL

x 2

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.inddPage 1

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Drawer Assembly

Step 1.

Secure drawer base to drawer side using 4 x 16mm drawer

runner screws (J) in holes provided.

Seat the edge of drawer base tight into corner of casing, as

shown.

The decorative face of drawer base

to be positioned as shown.

Drawer

base

Fixing

clip

& (Q)

Fixing

clip

& (Q)

Drawer

side

Drawer side

xing clip

Step 2.

Clip on metal back panel

to drawer base & drawer

sides.

Y & L Y & L

Step 5.

Draw Adjustment

Screw point 1as shown to

adjust drawer frontal

right & left.

Step 6.

Fit Gallery Rail into the

top corners of Metal

Back-panel.

Locate front end of the

Gallery Rail into the

opening of the gallery

Head, which is secured to

the frontal as shown

Step 7.

Fit Drawer Cover Caps

over drawer side adjustment.

Drawer

Cover Cap

Drawer Frontal

Adjustment

Screw point 2a

as shown to adjust

drawer frontal up & down.

Tighten 2b

once in position.

Releasing xing clip.

Screw point 3

whilst applying downward pressure as

shown to release. View on side of drawer side

Deep

drawer

Front of drawer

Decorative

face

Drawer

base

JMetal back

panel

Drawer base

white decorative

face up

Step 3.

Screw back panel in position using

2 x 16mm screws (J) to drawer base in

holes provided.

Step 4.

Frontal Attachment

Secure Drawer Side Fixing Clips using

4 x 21mm screws (Q) and

Gallery Head (Y) using 2 x 21mm screws (L) in

pilot holes provided as shown.

Fixing

clip

Gallery

Head

Repeat step 1 so both drawer

sides are attached to drawer base.

Drawer

frontal

Drawer

frontal

View from

back

Metal

back

panel

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd

Page 2

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Assembly Guide

REQUIRED TOOLS

NOT to be used

with CAM DOWEL

& CAM LOCK

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd

Page 3

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Assembly Guide

BEFORE YOU START

INSTALLATION

SHOULD BE

PERFORMED BY A

COMPETENT

PERSON ONLY.

THIS PRODUCT COULD

BE DANGEROUS

IF INCORRECTLY

INSTALLED

(F) x24

Wooden

Dowel

(L) x24

15mm

Screw

(G) x20

Cam Dowel

(Expanding)

(H) x20

Cam lock

(M) x4

Cover Cap

(K) x16

30mm

Screw

(R) x30

19mm

Screw

(N) x2

Door Buer

(U) x2

Fixing Plate

(Z) x12

Shelf Peg

Plastic

LGE L BRACKET

SML L BRACKET

(FF) x4

HINGE MOUNTING PLATE

x2 Inc Screws

HINGE

x2 (Inc Screws)

Panel B

x2 End Panel

Panel A

x2 Back Panel

Panel E

x2 Rail

Appliance Shelf

Legs

Frontal

x1 (Packed separately)

Panel C

x24 End Panel

600+450 Appliance

Inc 1 Door + 1 Drawer

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd Page 4

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Assembly Guide 2070

Step 1.

Hinge Mounting Plate

Attach hinge plates onto end panels (B) in locations shown using 4x 15mm

screws (L).

Hinge side to be mounted in accordance to customer kitchen plan.

600+450 Appliance

Inc 1 Door + 1 Drawer

N.B. L Bracket

For appliance shelf, secure

to panel (B) using

4 x brackets (FF)

locate according to

customer appliance

requirements.

1826mm

1794mm

1826mm

1794mm

1592mm

1560mm

1592mm

1560mm

Fixed Shelf 1468mm Fixed Shelf 1468mm

Fixed Shelf 282mm Fixed Shelf 282mm

BTM BTM

TOP TOP

74mm 74mm

37mm

261mm

from base from base

from front

LEFT HAND RIGHT HAND

L L

Example

Locations

ONLY

Example

Locations

ONLY

FF FFFF FF

Drawer runner position

600+450 Appliance

Inc 1 Door + 1 Drawer

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.inddPage 5

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Assembly Guide

2250 Tall

Step 2.

Hinge Mounting Plate

Attach hinge plates onto end panels (B) in locations shown using

4x 15mm screws (L).

Hinge side to be mounted in accordance to customer kitchen plan.

N.B. L Bracket

For appliance shelf, secure

to panel (B) using

4 x brackets (FF)

locate according to

customer appliance

requirements.

2006mm

1974mm

2006mm

1974mm

1485mm

1453mm

1485mm

1453mm

Fixed Shelf 1367mm Fixed Shelf 1367mm

Fixed Shelf 282mm Fixed Shelf 282mm

BTM BTM

TOP TOP

74mm 74mm

37mm

261mm

from base from base

from front

LEFT HAND RIGHT HAND

L L

Example

Locations

ONLY

Example

Locations

ONLY

FF FFFF FF

Drawer runner position

Step 1.

To attach drawer runner screw into end panels (B) using

2 x 16mm screws (J) per drawer rail, into pilot holes provided,3rd hole from

front, as shown.

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd

Page 6

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Assembly Guide

N.B. L Bracket

For appliance shelf, secure

to panel (B) using

4 x brackets (FF)

locate according to

customer appliance

requirements.

Step 5.

Carcass Construction

Attach Panels (C) & (E) to panels (B),

using cam dowel (G) & cam lock (H) (in blue),

and also using dowels (F) (in orange)

in positions as shown.

Step 6.

Cam Lock (H)

Join panels (C) & (E) to (B).

Insert cam lock (H).

Do NOT tighten until Step 9.

NB. All Cam Locks (H) are to be positioned facing the

outside of the unit carcass, for ease of tightening.

Do not use power tools with

cam dowel (G) or cam lock (H)

Seat (G)

cam dowel

into hole

as shown

Step 3.

Seat dowel (F) into holes in

both end panels (B) as shown.

Step 4.

Seat cam dowel (G) into

holes in both end panels (B)

as shown.

View from underside View from underside

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd

Page 7

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Assembly Guide

9mm

Step 7.

Cut back panel (A)

to suit appliance

option, to leaving the

centre appliance aperture open.

A A

Step 8.

Slide back panel (A) into

groove of end panels (B).

Once back panel (A) is in position,

ensure the panel is ush & square with

bottom of end Panels (B).

Step 10.

Ensure carcass is square. Secure back

panel (A) with 12 x 30mm screws (K)

equally spaced at the top & bottom of

back panels (A) into base panels (C),

as shown.

Ensure you screw into the centre of base

panel (C) (9mm from the top or bottom

edge where applicable).

Step 9.

Hand tighten all cam locks (H), this will

expand cam dowels (G) and tighten

the unit together.

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd

Page 8

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Assembly Guide

9mm

Step 11.

Secure each of the legs into place with 2 x 15mm screws (L) per leg

Step 13.

Push leg rmly down into leg base.

Adjust legs to 155mm before turning carcass

upright. Once in situ level accordingly.

Step 12.

Lightly hit centre peg of leg base with hammer

until ush with the leg base.

Ensure legs are rotated as shown so that part

of it is supporting the end panels (B).

Front legs should have at edge to the front.

Front

Leg position diagram

For Internal Use: FI.WR.INS.043_WKIN00143_TOWER_600_2AppIncDr+Drw_Rev3.indd

Page 9

TOWER UNIT

600 Double Appliances

Inc Dr+Drw

Assembly Guide

Secure tower to the wall using L brackets.

Use 2 x 15mm screws (L) to secure each of the L

brackets to the cabinets at either side. Then screw

through into the wall as shown.

Screws for xing to walls are not provided as

these vary depending on your wall material and

construction. Ensure appropriate xings for

wall constructions are used.

Secure tower to the wall using screws through rail panel (E) into the

wall as shown.

Screws for xing to walls are not provided as these vary

depending on your wall material and construction. Ensure

appropriate xings for wall constructions are used.

Securing to Adjacent Units

Screw into any side units using

the 30mm screws (K) provided to secure to unit.

Screw just to the rear of the Hinge Mounting Plate,

at the top and bottom of both sides of the unit,

place a cover cap on the head to conceal it.

Andere Handbücher für TOWER UNIT

Inhaltsverzeichnis

Andere Wren Inneneinrichtung Handbücher

Wren

Wren PEBBLE FI.PK.BED.222.002 Montageanleitung

Wren

Wren 800 Bedienungsanleitung

Wren

Wren Feature Robe Bedienungsanleitung

Wren

Wren FI.PK.BED.222.001 Montageanleitung

Wren

Wren FRONTALS INFINITY Bedienungsanleitung

Wren

Wren TOWER UNIT 2070 Bedienungsanleitung

Wren

Wren 2070 Bedienungsanleitung

Wren

Wren UNDER ROBE 1 Montageanleitung

Wren

Wren 1000 Tall Bedienungsanleitung

Wren

Wren TOWER UNIT Bedienungsanleitung

Wren

Wren FI.PK.FIT.010 Montageanleitung

Wren

Wren INFINITY PLUS FI.PK.BED.111.010 Bedienungsanleitung

Wren

Wren 972 L Corner Bedienungsanleitung

Wren

Wren 1000 2 Drawer Bedienungsanleitung

Wren

Wren PEBBLE FI.PK.BED.222.005 Montageanleitung

Wren

Wren 600 Bedienungsanleitung

Wren

Wren ROBE UNIT Gebrauchsanweisung

Wren

Wren INFINITY Bedienungsanleitung

Wren

Wren Wall unit Bedienungsanleitung

Wren

Wren INFINITY PLUS Bedienungsanleitung

Wren

Wren WALL Series Bedienungsanleitung

Wren

Wren TOWER UNIT Bedienungsanleitung

Wren

Wren 800 2 Drawer Bedienungsanleitung

Wren

Wren FEATURE CHEST 1 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung